FENCE RULES – CHILLICOTHE (CITY), MISSOURI

OVERVIEW

This page covers residential fences inside the incorporated City of Chillicothe, Missouri, in Livingston County. It does not cover Chillicothe Township or property outside the city limits merely because it has a Chillicothe mailing address.

Chillicothe requires a permit and scaled site plan for new fences, with a published $25 fence fee. Its height rules distinguish residential corner visibility from tall fences along a lot division line; six feet is not a simple citywide maximum. Outdoor private pools and other pools of water deeper than eighteen inches require a permanent sixty-inch fence under the zoning and nuisance provisions, alongside separate gate and construction requirements. Electric and barbed fencing are restricted, while ordinary wood, vinyl/PVC and chain-link materials are not individually classified in the general yard-fence provisions. Historic review, drainage, floodplain conditions, outdoor storage and backyard chicken enclosures can add requirements. Updated November 2026.

Quick question Chillicothe answer
Permit or approval A permit and scaled site plan are required for new fence construction. The published fence fee is $25. Other approvals depend on the property and work.
Typical fence height Fences over 6 feet along a division line have specific residence- and street-separation conditions. Residential corner triangles have a 3-foot limit. Pool and outdoor-storage barriers have separate minimums.
Placement & property lines No separate general side- or rear-property-line fence setback is specified. Tall-fence, street-line, corner, pool, public-way, drainage and recorded-rights conditions remain applicable.
Common fence materials Wood: not specifically classified for ordinary yard fences. Vinyl/PVC: not specifically classified. Chain-link: not specifically classified for ordinary yard fences; pool-barrier construction has separate requirements.
Important local conditions Fence rules may be further affected by private pools, corner visibility, tall division-line fencing, outdoor storage, historic designation, floodplain and drainage conditions, public ways, easements and chicken enclosures.
Official local resource Chillicothe Codes and Zoning Department

The table summarizes the ordinary framework. The sections below preserve the conditions, exceptions and site-specific rules that determine how each requirement applies.

GOVERNANCE

Chillicothe is a special-charter city. The City Council adopts municipal zoning and construction requirements for property within the city. The Codes and Zoning Department administers building and zoning matters, and the locally adopted residential code identifies the Zoning Administrator as the building official. The city adopts the 2021 International Residential Code with local amendments, alongside the 2021 International Building Code and locally amended 2015 International Property Maintenance Code. These are separate from the city’s zoning and nuisance provisions.

The City Engineer administers the grading and storm-drainage provisions. The Zoning Administrator is the floodplain administrator. The Historic Preservation Commission performs the defined review of designated historic properties, and the City Council has the stated public-way encroachment approval role. The Board of Adjustment handles the applicable appeals. A building permit does not replace these separate approvals or establish private ownership, easement rights or responsibility for a shared fence.

PERMIT AND APPROVAL REQUIREMENTS

• New fence permit and fee: Section 405.2070’s permit and fee provisions expressly include fences among new construction requiring a scaled site-plan drawing. The drawing shows a north arrow, proposed construction dimensions, distances to property lines and adjacent streets. The published fence permit fee is $25. Required fees are paid before issuance. Starting work before obtaining a required permit triggers an additional investigation fee equal to the permit fee.

• Plans and approval: The required plans identify existing and proposed work and relevant easements, drainage, grades and site conditions. The city’s building permit application also identifies corner-lot, historic, erosion-control and flood-elevation information where applicable. A permit is issued for work that complies with the applicable requirements; approved plans remain at the site. The local residential-code amendment states that permits become void after 180 days. Section 405.2070 separately provides for expiration 180 days from issuance unless the Building Official notes a different period on the permit. The Building Official may grant written extensions of no more than 180 days each upon a written request demonstrating justifiable cause. An expired permit requires a new permit; the reissuance fee is one-half the amount required for a new permit, excluding the plan-review fee, only if the original plans and specifications have not changed and will not change.

• Repairs and replacement: Section 500.030 deletes the adopted residential code’s fence item from the work-exempt-from-permit list. The local amendments do not establish a separate blanket exemption for replacing an existing fence. The adopted code distinguishes construction and alterations from ordinary repairs; the extent of proposed work determines that classification. An existing fence’s presence does not itself exempt a replacement or authorize an increase in nonconformity. A specific ordinary-repair exemption for a proposed fence repair is a determination for Codes and Zoning.

• Contractors and owner-performed work: City contractor licensing is separate from the fence permit. The contractor definition excludes an owner personally performing work on an owned and personally occupied single-family residence or its accessories, subject to the stated repeat-work limits. The exclusion does not apply when the owner constructs a new personal residence more than once within five years or performs the specified work on more than one owned residence or its accessories within five years. Owner-performed work still must satisfy applicable permits and construction requirements.

• Designated historic properties: Work requiring a building permit and affecting the exterior architectural significance of a designated landmark or a structure in a designated historic district enters the certificate-of-review process in Sections 405.945–405.949. The code office forwards the completed application within seven days without an additional owner paperwork requirement under that provision. The commission reviews it and issues its certificate and recommendations under the stated seven-day-after-review and thirty-day-from-receipt provisions. The recommendations are expressly voluntary. Ordinary maintenance within the ordinance’s limits is excluded. This is not a mandatory historic design-approval process for every city fence.

• Mapped floodplain development: Construction or other covered development in the mapped flood-hazard areas requires a development permit from the Floodplain Administrator. The city provisions use the December 20, 2019 flood insurance rate map, as amended. The application identifies the work, location, use, value and relevant floodway, flood-fringe and elevation information, with the required plans. Floodplain approval is separate from the ordinary fence permit.

• Grading and storm drainage: Chapter 510 requires a permit before construction, alteration or reconstruction of a storm-drainage facility. Clearing, grading, borrowing or filling requires a permit from the City Engineer. For such work on a tract greater than five acres, the grading permit must be issued in conjunction with a building permit under Chapter 500; a grading permit issued without a building permit expires within one year. For low-density residential lots with no more than two dwellings, the City Engineer handles drainage conditions and may waive a drainage plan when the work does not materially change or increase water flow. A plan waiver does not establish a general permit exemption.

• Larger earth disturbance: Under Section 405.1280’s special-requirement process, an erosion and sedimentation plan is required with the building application when excavation or fill exceeds 500 cubic yards, fill exceeds 3 feet above natural ground, excavation or fill covers more than 5,000 square feet, or plant/tree cover is removed from more than 5,000 square feet. The plan describes the disturbance and protective measures; the Planning and Zoning Commission may require additional reasonable measures. Separately, Missouri’s construction land-disturbance permit applies at one acre or more, including smaller work that is part of a common development or sale plan cumulatively disturbing at least one acre. That program requires a site-specific stormwater pollution prevention plan.

• Pools and other separate permissions: The city’s fee schedule separately lists a $25 pool permit and $10 annual pool inspection. Public-way encroachment permission, the applicable grading or floodplain approvals, and any special screening requirements remain distinct. A listed grading, digging or right-of-way charge is not automatically an added fee on every fence project.

FENCE PLACEMENT RULES

• Private property lines: The zoning ordinance does not specify a separate general side- or rear-property-line setback for ordinary fences. The tall division-line fence rule, corner visibility rule and street-line wording described below still apply. Ordinary building-yard dimensions are not a separate fence-setback schedule. The city’s permit application does not require a boundary survey, but expressly states that permit issuance does not determine ownership or property boundaries. A fence location must respect the actual boundary and recorded rights.

• Public ways: Section 505.200 prohibits an obstruction or encroachment in a public street, alley, sidewalk or other public way without City Council permission, unless expressly allowed by ordinance. This is separate from a private property-line setback. A permit for work on the owner’s lot does not grant permission to occupy public land.

• Easements and drainage: Recorded utility, access and drainage easements may restrict placement and require access to remain available. The subdivision code’s utility-easement width is not a universal fence setback. The applicable easement or plat controls its actual location and rights. Storm-drainage facilities and access easements remain subject to their maintenance requirements, including control of erosion, silt, debris and vegetation. Fence work does not authorize obstruction of those facilities or alteration of approved drainage.

• Floodways and flood-prone sites: In a designated regulatory floodway, encroachment requires the specified hydrologic and hydraulic demonstration that it will not increase base-flood levels. Before a floodway is designated, development in a numbered A zone or AE zone must demonstrate that the proposed work, combined with all other existing and anticipated development, will not raise the base-flood water-surface elevation more than one foot anywhere in the community. Applicable development must use design or adequate anchorage to prevent flotation, collapse or lateral movement from water pressure, flowing-water loads and buoyancy, use flood-resistant materials and follow methods that minimize flood damage. These conditions are tied to the mapped site and work, not every fence in the city.

• Pool setbacks: Section 405.1200 applies to an outdoor pool, pond, lake or open tank containing or normally capable of containing water deeper than one and one-half feet. The pool, including adjacent walks, paved areas and accessory structures, must be at least 5 feet from property lines. This pool rule does not establish a five-foot setback for every yard fence.

• Survey markers: Missouri Section 60.355 protects the listed public-land-survey corners, boundary markers, benchmarks and horizontal-control monuments from knowing removal, movement, defacement or destruction, with an exception for a registered land surveyor. The statute provides a class B misdemeanor classification, restoration-cost liability and the affected owner’s stated surveying-cost and attorney-fee remedy. A fence permit does not authorize moving a protected marker.

• Excavation notice: Fence-post excavation, including covered hand digging, augering or driving, is subject to Missouri’s underground-facility law. Section 319.026 requires notice to the notification center at least 2 working days, but not more than 10 working days, before the expected start. The statutory period begins at midnight following receipt; Saturdays, Sundays and legal holidays are not working days. Notice identifies the excavator, responsible person, location, expected start, depth and type of excavation, and the other required site/contact information. The notice service is Missouri 811. Utility locating does not establish property boundaries or grant permission to enter another property.

• Responses and an unanswered notice: Under Section 319.030, participating operators ordinarily respond within two working days unless an extension is agreed. Early excavation requires the law’s confirmation that all facilities have been located. If an operator has not responded after a proper original notice, the excavator must give the prescribed second notice before beginning. The operator then has two hours to mark or contact the excavator; a second notice received by 2 p.m. requires marking that working day, and a later notice requires marking by 10 a.m. the next working day. Only the statute’s failure-to-mark-or-contact conditions allow excavation after that process. An unanswered first notice is not immediate permission to dig, and careful work remains required.

• Ticket life and markings: The notice has an operational life ending at 11:59 p.m. 21 consecutive calendar days from the start date of work. Work may continue within the described area while the notice remains valid and markings remain visible. If work cannot begin within ten working days as described in the request, a relocate request is required before starting. Unusable marks require a remark request with the original notice timing. Excavators must reasonably preserve markings; unnecessary repeat marking caused by a failure of care can create cost liability.

• Care near facilities: The statutory approximate-location strip is ordinarily no wider than the facility width plus two feet on each side. When reinforced concrete, multiple adjacent facilities or other specified unusual conditions interfere with locating, the operator designates a wider approximate area to the best of its ability. Before excavation, the excavator determines best practices for confirming horizontal and vertical location in the actual site conditions; hand or soft digging is used when possible. An incorrectly located or unmarked facility must be reported through the notification center, and the operator must respond within two hours by contact or correct locating. The limited exclusions for specified tillage or temporary markers are not a general exemption for structural fence-post holes.

• Damage and emergency work: Damage, dislocation or disturbance of a facility or its protective items, including trace wires, encasements and protective stakes, must be reported to the notification center. Pipeline contact or damage causing a hazardous-liquid or gas release requires an immediate 911 call. The excavator must not conceal damage or attempt repairs without the facility owner’s authorization. Emergency temporary sewer repairs after notification are narrowly allowed to prevent further damage; they do not remove the reporting duty. A genuine excavation emergency permits necessary work with all reasonable precautions to protect facilities and notice as soon as practical. Within two hours of receiving the emergency notice, the operator must mark or contact the excavator with available information and, if unable to mark within that time, state when marking will occur. Separate Missouri Department of Transportation permission applies to excavation in a state highway or its right-of-way under Section 319.025, subject to its railroad-right-of-way exception.

• Division fences and neighboring land: Missouri’s statutory partition-fence systems address their own livestock and shared-fence circumstances. They are not a city rule requiring every neighbor to pay half of an ordinary yard fence. The applicable system, use and agreement determine any contribution, repair-entry or removal rights; municipal permit approval determines none of those private rights.

FENCE HEIGHT AND VISIBILITY RULES

• Residential corner lots: Section 405.1230 prohibits a fence, plant or other obstruction more than 3 feet above the plane of the established street grades within the specified front- or side-yard corner triangle in Residence Districts. The triangle is bounded by the intersecting street lines and a line joining points 20 feet from their intersection, measured along each street line. Foliage also may not materially obstruct an approaching driver’s view in the Zoning Inspector’s judgment.

• Tall division-line fences: Section 405.1230(B) regulates a fence more than 6 feet above the plane of the finished grade of the lots at their division line. Such a fence cannot be erected along that line unless no part is within 20 feet of a residence building on the same or an abutting lot. The sentence also states that in no instance shall a fence be nearer than twenty feet to a street line. It does not separately explain whether that final street-line clause extends beyond the tall division-line fences addressed in the sentence. Codes and Zoning determines that street-frontage application; the ordinance does not supply an unqualified permission to place shorter fences at the street line.

• Ordinary yard heights: The zoning provisions do not provide a separate front-, side- and rear-yard maximum schedule beyond the applicable conditions above. Six feet is therefore not an unconditional citywide maximum or a promise that a six-foot fence fits every location. Special pool, outdoor-storage, screening and enclosure rules remain separate.

• Private pools: Under Section 405.1200’s private-pool requirements, the pool or entire property must be walled or fenced to prevent uncontrolled access by children from streets or adjacent property. The pool also requires screening by a masonry wall, fence or compact hedge at least 5 feet high and kept in good condition. A pool or other pool of water more than 18 inches deep must be enclosed by a permanent fence at least 60 inches high with a lockable gate. Leaving the gate unlocked while the pool is not in use is a public nuisance. Hedge screening alone does not replace that permanent fence.

• Outdoor-storage enclosures: Section 215.040’s nuisance provisions require at least a 72-inch fence with a lockable gate around the specified outside storage of tools, equipment, machinery, nonworking vehicles or parts, household appliances and broken furniture. An unlocked gate while the backyard is unoccupied constitutes a nuisance. This enclosure does not override the separate requirement that the specified unlicensed vehicles be kept in an accessory building or garage out of view.

• Specially required screening: Under Section 405.1280, the Planning and Zoning Commission may impose screening on the stated principal, accessory or special uses within 50 feet of a residential district. The specified arrangement is a 30-foot open-space buffer with a fence or vegetative screen at least 90 percent opaque and at least 6 feet above the residential district’s property level at its boundary. The commission may allow lesser wall, fence or planting screens upon the ordinance’s equivalent-protection or light-and-air findings. This is a conditional screening provision, not an automatic requirement on every residential lot line.

MATERIAL AND CONSTRUCTION LIMITS

• Wood: The general residential yard-fence provisions do not separately classify wood as an expressly approved or prohibited material. Maintenance, dangerous-feature, screening, pool and special-use conditions still apply.

• Vinyl/PVC: The general yard-fence provisions do not separately classify vinyl or PVC. Their absence from a material list does not waive the applicable height, placement or construction conditions.

• Chain-link: The general yard-fence provisions do not separately classify chain-link. Pool barriers have a separate technical construction framework, so an ordinary yard-fence material choice does not establish that a proposed pool enclosure complies.

• Electric, barbed and dangerous fencing: Section 215.040(B)(19) prohibits electric fences and fences built wholly or partly of barbed wire, except in areas zoned agricultural. Acreage or agricultural activity alone does not establish that zoning exception. Section 505.040 separately prohibits dangerous spikes, sharp-pointed cresting, barbed wire and similarly injurious features beside streets or sidewalks. The agricultural exception does not erase the separate public-way safety provision.

• Maintenance and retaining walls: The locally amended property-maintenance code requires fences, walls and retaining walls to remain structurally sound and in good repair. The general yard-fence provisions do not prescribe a universal finished-side orientation, opacity percentage or a separate approval list for composite, bamboo, salvaged material or individual metals. A retaining wall is subject to its applicable construction and site requirements; the fence provisions do not establish a blanket retaining-wall permit exemption.

• Local pool-barrier construction: Section 500.030’s residential-code amendments specify a barrier at least 48 inches above finished ground on the side facing away from the pool, no more than 2 inches between the ground and barrier on that side, and no more than 4 inches between the top of an aboveground pool and a barrier mounted there. Gates open away from the pool and are self-closing and self-latching. These construction provisions do not reduce the separate sixty-inch permanent-fence requirement for pools covered by Section 405.1200.

• Existing pools, hot tubs and spas: The locally amended property-maintenance provision separately addresses private pools, hot tubs and spas capable of holding eighteen inches of water, with a forty-eight-inch barrier measured from outside finished ground. Gates and doors in the barrier must be self-closing and self-latching, with the self-latching device’s release mechanism on the pool side of the gate. The gate must positively close and latch when released from an open position six inches from the gatepost. Existing enclosures may not be removed, replaced or changed in a way that reduces their effectiveness as safety barriers. That provision has an ASTM F1346 safety-cover exception for hot tubs and spas; it is not a stated repeal of the separate zoning fence rule.

• Detailed pool specifications and exceptions: The local amendment’s remaining barrier items refer to items 2 through 10 in the International Residential Code without identifying a corresponding section. The adopted model framework also refers to the International Swimming Pool and Spa Code. The published local wording does not resolve that cross-reference or every interaction among cover, pool-wall and other barrier alternatives. Chillicothe Codes and Zoning is the responsible office for the applicable opening, latch, climbability, alternative-barrier and exception details. The city’s independent zoning provision does not state an express safety-cover or pool-wall exception to its permanent-fence requirement.

• Historic and special screening design: Historic review considers such features as height, scale, material, texture, relationships to surrounding features and landscaping, with the voluntary recommendations described above. Special screening required under Section 405.1280 must be architecturally harmonious with the principal structures and maintained so it does not become unsightly, hazardous or less opaque. Where the commission imposes the associated landscaping requirements, disturbed open areas must be contoured for drainage and landscaped under the approved plan, apart from the stated parking, drive and storage areas; the owner maintains that landscaping.

• Backyard chicken enclosures: Section 205.180 allows licensed, noncommercial chicken-hen keeping on detached single-family lots, not multifamily or duplex properties; roosters are prohibited. Coops and pens are limited to the rear yard and must meet the accessory-building size, setback and height requirements. The coop must contain at least 16 square feet. If it provides less than sixteen square feet per hen, a fenced exercise yard with at least 10 square feet per hen is required. Wire netting or another escape-preventing enclosure must be kept in good repair and free of peeling paint, untreated or rotted wood, and rust. A coop over 120 square feet requires a building permit. These are chicken-enclosure requirements, not ordinary yard-fence dimensions.

PRIVATE RESTRICTIONS

Recorded covenants, subdivision restrictions, homeowners-association architectural rules, private easements and enforceable boundary or maintenance agreements may add obligations beyond the public fence rules. Section 405.1160 recognizes that more restrictive applicable provisions can operate alongside the zoning ordinance. The actual instrument and applicable Missouri law determine a private restriction’s scope; there is no universal private height or material rule for every Chillicothe lot.

A city permit does not decide the property boundary, confer ownership of a shared fence, settle a cost allocation or authorize interference with another person’s access rights. Public statutory partition-fence obligations are separate from a private agreement. The age or position of an existing fence alone does not resolve a title dispute, and a fence across an easement does not automatically become permissible merely because it has a gate.

REVIEW AND ENFORCEMENT CONTEXT

Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:

• Permit and site review: New fence plans, proposed repair or replacement classification, applicable historic review, and separate grading or floodplain approval.

• Placement and visibility: Corner obstructions, tall division-line fences, street frontage, public-way encroachments and interference with drainage or recorded access.

• Construction and maintenance: Pool gates and barriers, dangerous or restricted fencing, deteriorated fences and walls, and the specified storage or animal enclosures.

• Separate private matters: Covenant enforcement, ownership, boundary, easement and shared-cost disputes remain distinct from municipal permit and code enforcement.

USING THIS INFORMATION

This page provides general orientation on how residential fence rules are structured and applied within the City of Chillicothe, Missouri. Updated November 2026.

In addition to local fence rules, certain Missouri laws apply statewide. See Statewide Fence Laws in Missouri.

It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with the identified municipality, including its actual municipal or county class, charter, adopted program or special district, and each function’s verified territory, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Missouri law. Applicable requirements depend on the property’s actual facts and the respective authority of the identified offices. Private agreements and recorded rights remain separate from government approvals. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern.