FENCE RULES – SPEEDWAY (TOWN), INDIANA
OVERVIEW
This page covers single-family residential fence work within the Town of Speedway’s corporate boundaries in Marion County, Indiana. Speedway has its own municipal ordinances and construction administration, while the Indianapolis–Marion County metropolitan zoning and subdivision ordinance governs land use within the Town. The applicable zoning district, recorded plat and any approved development plan determine which additional conditions affect a particular lot.
Speedway’s fence rules combine express permit exclusions with detailed zoning standards. The Town building-code chapter excludes fences, and the metropolitan ordinance exempts fences and structural barriers from an Improvement Location Permit. In Dwelling districts, ordinary limits are 3.5 feet in front and six feet at the sides and rear, with a four-foot front-yard option for sufficiently open fencing. Town and metropolitan visibility rules use different sight-area measurements. Chain-link treatment varies by district, and SZ-1 prohibits it. Pools have overlapping Town, metropolitan and state enclosure provisions that require particular care.
| Quick question | Speedway answer |
|---|---|
| Permit or approval | Fences are excluded from the Town building-code chapter and exempt from the metropolitan Improvement Location Permit requirement. Zoning, special-district plans, floodplain development, pool work and other site-specific approvals remain separate. Retaining walls have separate treatment. |
| Typical fence height | Dwelling districts: 3.5 ft front; four ft front at 30% opacity or less; six ft side/rear. Corner/through lots, topography, posts, adjoining districts and game courts have additional rules. Visibility restrictions can prohibit a fence in a sight area. |
| Placement & property lines | Compliant fences/walls may reach a lot line. Public rights-of-way, Town and metropolitan sight triangles, recorded easements, drainage plans, stream corridors, pool separation and approved development plans can restrict that location. State enclosure, joining and removal duties can also apply. |
| Common fence materials | Wood: expressly recognized. Vinyl/PVC: not named as a freestanding material; simulated-material and building-compatibility clauses apply. Chain-link: recognized with district-specific yard/coating/slat limits; prohibited in SZ-1. |
| Important local conditions | Fence rules may be further affected by corner and through lots, Compact Context mapping, SZ-1 or planned-development conditions, pool-enclosure requirements, floodplain or stream-corridor location, drainage and utility easements, automatic access gates, chicken enclosures, boundary live fences, qualifying agricultural partition fences and private restrictions. |
| Official local resource | Town of Speedway zoning and variance information |
The table is for quick reference. The sections below explain the detailed rules and their exceptions. Before purchasing materials or beginning construction, read the sections that apply to the property, review the linked official sources, and confirm site-specific questions with the Speedway Building Commissioner, Indianapolis Department of Metropolitan Development or the office responsible for the particular approval.
GOVERNANCE
Speedway is an incorporated town. Its municipal rules operate alongside the Indianapolis–Marion County Consolidated Zoning and Subdivision Ordinance, effective August 19, 2026. That ordinance applies throughout Marion County, including Speedway. The Department of Metropolitan Development administers the metropolitan land-use framework. Speedway’s Board of Zoning Appeals has variance jurisdiction within the Town’s corporate boundaries, rather than the Metropolitan Board of Zoning Appeals.
The Speedway Municipal Code supplies the Town’s building-code scope, intersection visibility, pool fencing, dwelling maintenance and fire-access gate provisions. The Speedway Building Commissioner and Inspection Department administer local construction requirements; the Clerk-Treasurer issues Town construction permits. A fence’s exclusion from the building chapter is distinct from the zoning standards that govern its height, materials and location.
The metropolitan Department of Business and Neighborhood Services administers the ordinance’s floodplain-development permit provisions. Speedway administers its municipal stormwater program, subject to current Indiana law and Indiana Department of Environmental Management requirements. The Town fire chief or designee administers the published fire-access gate provisions. Approved development plans and recorded commitments can supply additional property-specific conditions, particularly in D-P planned developments and the Speedway special districts.
PERMIT AND APPROVAL REQUIREMENTS
• Ordinary fences — Town building code: Section 15.04.040 expressly excludes fences from the Town building-code chapter. Section 15.04.160 repeats the exclusion. Ordinary fences are outside this chapter’s permit requirements. Retaining walls and other construction require their own applicable classification.
• Improvement Location Permit: Metropolitan Section 740-801.A.3.e exempts the creation or alteration of fences and structural barriers from an Improvement Location Permit (ILP). The ordinance expressly retains the applicable zoning standards for exempt work.
• Indiana residential-code framework: The 2020 Indiana Residential Code adopts the 2018 International Residential Code with Indiana amendments and operates statewide within its scope. Speedway administers its local construction permits and inspections. The express Town and metropolitan fence exclusions described above govern ordinary fence permit treatment.
• Speedway special districts and planned developments: In SZ-1 and SZ-2, the metropolitan ordinance provides site-and-development-plan review and an Administrator-review route for specified smaller improvements. Fencing materials and design are expressly among the design considerations. On D-P property, approved development plans, perimeter treatments and recorded commitments govern the approved development. These requirements concern the applicable district and approval; the ILP exemption does not resolve whether a proposal changes an approved plan.
• Pools and hot tubs: Metropolitan Section 743-306.JJ requires an ILP before installation of a pool or hot tub with more than 200 square feet of water surface. The Town’s structural application separately identifies pool work. Pool enclosure requirements are described under Material and Construction Limits because the Town, metropolitan and state provisions differ.
• Flood-hazard property: The metropolitan flood-control regulations expressly include walls and fences within development. The applicable Floodplain Development Permit is required before regulated development in a special flood-hazard area. For floodway work, the local process also requires the applicable Indiana Department of Natural Resources approval or determination that state approval is not required. A fence’s ordinary ILP exemption does not remove that separate floodplain process.
• Construction stormwater: The Construction Stormwater General Permit generally covers disturbances of one acre or more and smaller disturbances within a qualifying larger common plan of development or sale. Covered projects require the applicable stormwater pollution-prevention planning and permit coverage; individual residential lots may operate under the larger development’s coverage and lot-registration requirements. Under IC 36-1-3-14, local construction-stormwater requirements generally cannot exceed IDEM’s permit requirements. The statutory limits also govern local treatment of standalone projects below one acre. Construction-stormwater coverage is separate from recorded drainage obligations, access rights and stormwater-facility maintenance. See IDEM’s current construction-stormwater requirements and local-program limits.
FENCE PLACEMENT RULES
• Lot lines and required yards: Table 744-204-1 permits fences and walls meeting Section 744-510 to be located up to a lot line. The published fence allowance is separate from general building setbacks.
• Sidewalks and public rights-of-way: In Dwelling and Mixed-Use districts, Table 744-204-1 permits fences “within 1 ft.” of a sidewalk in the public right-of-way along local and collector streets, provided that location does not encroach into the right-of-way. The legal right-of-way boundary can differ from the curb or pavement edge.
• Boundary identification: A legal property line, zoning yard, public right-of-way and recorded easement are different boundaries. A tax map, GIS line, existing fence, hedge, mowing line or curb is not a substitute for the property’s legal boundary and the relevant recorded documents.
• Enclosing previously unenclosed property — existing fence payment: Under IC 32-26-2-15, when enclosing previously unenclosed property makes an existing fence a partition fence, the person enclosing the property must pay the existing fence’s owner 50% of its value, as estimated by that owner. Section 16 allows a civil action to recover unpaid compensation. If the enclosing person makes a pretrial offer covering at least the eventual damages and costs accrued through the offer date, and the fence owner rejects it, that owner bears the action’s costs and receives only the assessed damages. This chapter’s enclosure provisions are separate from the agricultural-land conditions of IC 32-26-9.
• Joining another owner’s fence when enclosing property: IC 32-26-2-17 requires the existing fence owner’s consent before a person enclosing previously unenclosed property joins a new fence to that fence. If consent is withheld, each owner must provide property equivalent to 50% of a lane’s width, or a reasonable distance, for erection of the second fence.
• Removing a partition fence when opening an enclosure: IC 32-26-2-18 applies when a person ceases using the property or opens the person’s enclosures. Before removing a portion of that person’s fence that partitions the property from another person’s enclosure, the person must give interested persons six months’ notice of the intended removal.
• Fence mistakenly erected on another person’s land: Under IC 32-26-2-19, the person who mistakenly erected the fence may enter the other person’s land to remove it within six months after determination of the legal property line, after paying or offering reasonable damages for injury caused by crossing the land. Section 20 protects an enclosed field containing a crop: removal cannot expose it until the crop has been gathered and removed, secured against injury, or could have been gathered and secured with reasonable diligence. Once that crop condition is met, the fence and materials may be removed immediately even if the six-month period has passed.
• Agricultural partition fences — land and municipal-boundary scope: IC 32-26-9 applies only where at least one adjoining parcel is agricultural land: land zoned or otherwise designated agricultural, used for growing crops or raising livestock, or reserved for conservation. Section 2’s construction duty concerns property outside, abutting or adjacent to a city or town’s corporate boundary. For a Speedway property, the municipal-boundary condition must be met as well as the agricultural-parcel condition. Ordinary interior residential parcels without a qualifying agricultural neighbor are outside this chapter. Within the chapter’s agricultural-land scope, Section 1 separately requires existing fences used by adjoining owners as partition fences to be repaired, maintained and paid for under the chapter unless the owners agree otherwise.
• Qualifying agricultural partition fences — location and allocation: For property subject to IC 32-26-9-2, the partition fence is built on the dividing property line. If the owners have not already divided responsibility and no other chapter provision controls, a north–south line assigns the north half to the east owner and south half to the west owner; an east–west line assigns the west half to the north owner and east half to the south owner. An owner who built another half and maintained it for at least five years may continue maintaining that portion. Construction, rebuilding and repair costs are proportionate to the rods or portion of fence each owner owns along the line, whether the owner holds a fee simple or life estate.
• Qualifying agricultural partition fences — notice and trustee process: Under IC 32-26-9-3, the interested owner who has built, rebuilt or repaired that owner’s own portion gives the defaulting owner, agent or tenant 20 days’ notice to do the defaulting owner’s portion. Continued default is reported to the township trustee. The trustee estimates the work’s cost and, within a reasonable time, sends the defaulting owner a statement and notice of probable cost. If the work remains undone 20 days after receipt of that notice, the trustee builds or repairs the fence, using only fence materials most commonly used by the community’s farmers. On a township line, the complaining owner’s township trustee has jurisdiction unless disqualified; a trustee who is related to an interested owner or is an interested owner is replaced under the chapter’s nearest-trustee provisions. The trustee’s certified actual costs pass through the county claim process and are assessed against the affected property and collected as taxes.
• Qualifying agricultural partition fences — ditches and creeks: If a ditch or creek crosses the division line and creates extra maintenance expense that the owners cannot apportion, IC 32-26-9-3 requires the trustee to appoint three disinterested citizens to apportion the fence to be built by each owner. If a ditch or creek instead forms or covers the dividing line and makes a boundary-line fence impracticable, each owner builds and maintains a separate fence on that owner’s property as near the boundary as practical, at that owner’s cost. Where a stationary stream-crossing fence is impracticable, the chapter requires floodgates or similar structures that restrain domestic animals, swing upward during high water and connect continuously with the partition fences. If extra expense produces a disagreement about the structure or cost shares, written notice to the trustee triggers appointment of three disinterested township citizens. Their majority decision is final and binding; each arbitrator receives $2, allocated in the same proportions as the structure’s expense. If an owner fails to construct or pay the assigned share within 30 days after that decision, the trustee constructs the structure and collects costs, including arbitrator compensation, through the partition-fence process. Repairs, rebuilding and replacement follow the determination. Floodway, drainage and other applicable approvals remain separate.
• Intersection and driveway sight areas: Both the Town’s 30-foot curb-line triangle and the metropolitan sight-area provisions can affect a street-edge or driveway fence. Their different measurements and the separate plat-covenant requirements appear under Fence Height and Visibility Rules.
• Recorded utility and drainage easements: Subdivision plats must identify easement dimensions and purposes. Metropolitan Section 741-307 generally requires utility easements totaling at least 10 feet, unless an applicable utility or city agency requires another size. Drainage easements must accommodate maintenance access. The actual recorded easement establishes the affected area on an existing lot; these subdivision dimensions are not a universal fence setback.
• Sanitary-sewer easements and drainage plans: The required subdivision covenants prohibit a building, structure, tree or other obstruction within a sanitary-sewer easement without express written permission that is recorded and runs with the property. The drainage covenant requires continuing compliance with the approved plat drainage plan and drainage permits. Fence posts, panels and gates must preserve the access and drainage obligations that affect their proposed location.
• Stream-protection corridors: Section 744-205 establishes corridors along mapped natural, non-intermittent streams, measured parallel to the top of bank. Category One streams use 60 feet in Compact Context and 100 feet in Metro Context; other mapped streams use 25 feet and 50 feet, respectively. A wetland extending beyond the required corridor expands it to include the wetland. The ordinance lists permitted corridor activities and requires replacement of removed trees or vegetation with native species at one shade tree and four large shrubs per 1,000 square feet disturbed. Fence-related clearing or construction within a corridor requires confirmation of its applicable treatment with the Department of Metropolitan Development.
• Floodways and floodway fringe: Nonbuilding structures in these areas must withstand the specified flood forces, protect against flood-related hazards and minimize obstruction of floodwater. The ordinance specifically identifies flow-through rather than solid fencing as an obstruction-reduction measure. State floodway requirements and any qualifying statutory exemption remain separate from local floodplain approval.
• Drainage facilities and access: Approved drainage plans, public drainage easements and required stormwater-facility maintenance access continue to govern the affected property. Stormwater-facility operation and maintenance obligations are distinct from the construction-stormwater acreage threshold. Where a regulated-drain right-of-way legally applies, its established boundaries and the responsible drainage authority’s requirements also need to be respected.
• Pool enclosures: Town Chapter 15.29 requires its enclosure to remain at least four feet from the pool perimeter. The pool’s own setbacks and the different enclosure provisions are separate from ordinary property-line fence placement.
• Indiana 811 before covered digging: Before covered fence-post excavation, submit a locate notice through Indiana 811 at least two full working days and no more than 10 calendar days before work. Working days run from 7 a.m. to 6 p.m., Indianapolis time, excluding weekends and state/national holidays. The normal lawful start is no earlier than 7 a.m. on the next working day after the two full working days have elapsed. Check all affected utilities’ responses and markings, and make the required affirmative acknowledgment to Indiana 811 before starting. Earlier work requires the statutory all-operator electronic-positive-response conditions. A notice expires at 11:59 p.m. Indianapolis time, 20 days after its receipt date; unfinished covered work requires a new notice and new operator markings before continuing. The narrow exception requires solely hand tools, property owned or controlled by the person digging, and depth no greater than 12 inches. Follow the IURC’s underground-facility protection guidance along with the current ticket instructions.
FENCE HEIGHT AND VISIBILITY RULES
• Dwelling-district baseline: Section 744-510 sets a 3.5-foot front-yard maximum, increased to four feet when opacity is 30% or less. Side- and rear-yard fences and walls may be six feet. The open-fence option concerns opacity, not a four-foot maximum for every front-yard design.
• Other zoning districts and adjoining boundaries: Table 744-510-2 provides these front/side-and-rear limits: C-1 and C-3: 3.5/6 feet; C-4: 3.5/10 feet; C-5: 5/10 feet; C-7: 6/10 feet; MU-1 through MU-4: 3.5/6 feet; other districts: 3.5/6 feet. Industrial districts permit 3.5 feet in required front yards in I-1/I-2, six feet in I-3/I-4, and 10 feet in side/rear yards. Industrial front transitional yards use 3.5 feet; other transitional yards use 10 feet. These branches matter where a residential use is lawfully subject to another district’s standards or the adjoining-district exception below applies.
• Dwelling lot adjoining a non-Dwelling district: Along a shared lot line between a Dwelling-district lot and a lot not zoned to a Dwelling district, the maximum fence/wall height is the greater of the two districts’ height limits. This exception applies along that lot line.
• Compact Context corner lots: For single-family attached or detached dwellings, two-family dwellings, triplexes and fourplexes on corner lots in the mapped Compact Context Area, a fence/wall may reach six feet in a yard that neither serves a dwelling’s primary entrance nor faces a dwelling’s primary entrance across the street. A portion above 42 inches cannot extend beyond the building line containing the primary entrance.
• Through lots: A fence/wall may reach six feet in a front yard that does not serve a dwelling’s primary entrance and does not abut a dwelling lot with a front yard on that street. A portion above 42 inches cannot extend beyond the building line established by the abutting lots.
• Measurement and posts: Measure from grade to the top of the fence/wall, excluding fence posts. Grade changes over two feet count in the height calculation, as does mounding that raises the fence above the surrounding ground level. Posts may extend one foot above the applicable fence maximum.
• Topographic drops: Along the portion of a fence/wall where the ground drops, its maximum may increase by the accompanying topographic drop, up to two additional feet. The increase is limited to that location.
• Residential game courts: A fence forming part of a regulation game court may reach 10 feet. This is a game-court exception, rather than an ordinary yard-fence maximum.
• Multifamily frontage exception: For a multifamily project in a Dwelling district with at least 500 linear feet of road frontage, a front-yard fence/wall may reach six feet. Within 15 feet of pedestrian or vehicular access, it must be reduced to 3.5 feet or have 25% opacity or less. This project-specific rule is separate from single-family fence limits.
• Town roadway/access-point triangle: Town Section 10.48.030 prohibits fences within a triangle extending 30 feet along the boundary of each intersecting roadway, measured from the intersection of curb lines, at roadway or vehicular-access intersections, except where traffic-engineering standards indicate otherwise. The same provision addresses plant material with a projected mature height over 30 inches; it does not provide a 30-inch fence allowance.
• Metropolitan driveway triangles — nonindustrial districts: Section 740-304 forms the triangle using the driveway and right-of-way centerlines and a line connecting their endpoints. The driveway-centerline leg extends 20 feet from the street pavement edge extended across the driveway. The right-of-way-centerline leg is 200 feet for arterials/highways/state roads; 150 feet for collectors; 100 feet for local streets; 30 feet for alleys; 75 feet for railroads; and 20 feet for greenways. Direct expressway access is prohibited.
• Metropolitan driveway triangles — industrial districts and active mining: For Industrial districts and active GSB mining operations, the driveway-centerline leg is 65 feet from the pavement edge. The right-of-way-centerline legs are 400 feet arterial/highway/state road, 300 feet collector and 250 feet local. These are separate from the nonindustrial driveway measurements.
• Metropolitan intersections of rights-of-way: The triangle is formed from intersecting right-of-way centerlines and a line connecting their extended endpoints. Distances along the respective centerlines are 120 feet arterial/highway/state road; 95 feet collector; 75 feet local; 40 feet alley; 75 feet railroad; and 20 feet greenway. Direct expressway access is prohibited. Section 744-503.H prohibits obstructions materially impeding visibility between 2.5 and eight feet above adjoining-right-of-way grade in the applicable clear-sight area.
• Recorded subdivision sight covenant: The metropolitan subdivision regulations require a covenant prohibiting fences, walls, hedges or shrubs that obstruct sight lines between 2.5 and nine feet above the street within a corner triangle measured 25 feet along the street right-of-way lines from their intersection or extended intersection at a rounded corner. The same sight-line limitation applies within 10 feet of the intersection of a street right-of-way line with driveway pavement or an alley line. This recorded-plat condition has a different origin and geometry from the Town and general metropolitan triangles.
• Boundary hedges and live fences: IC 32-26-5 applies to hedges or other live fences grown along lines dividing property owned by different persons. They must be cut and trimmed at least once each calendar year to no more than five feet high and three feet wide. These dimensions concern boundary live fences.
• Boundary live-fence complaints: An adjoining landowner’s signed written complaint alleging failure to trim a hedge/live fence covered by IC 32-26-5 triggers the township trustee’s examination within five days. If untrimmed, the owner receives written notice to cut and trim it and remove the brush to the owner’s property within 30 days after receiving notice. Notice is read to the owner or left at the usual residence; for an owner outside the township, it is mailed to the last known postal address. If the owner, agent or tenant does not comply, the trustee must arrange the trimming and brush removal immediately after the 30-day period and recover expenses by suit against the fence-property owner in the county’s circuit or superior court. The prosecuting attorney brings the suit in the state’s name on the trustee’s relation; the statute adds a $10 prosecuting-attorney fee to suit costs.
• Malicious nuisance fences: IC 32-26-10 treats a fence-like structure unnecessarily over six feet and maliciously erected or maintained to annoy an adjoining owner or occupant as a nuisance. An adjoining owner or occupant injured in comfort or enjoyment may seek damages, abatement and other nuisance remedies. These are conditions concerning the structure’s necessity, purpose and effects.
MATERIAL AND CONSTRUCTION LIMITS
• Ordinary fence materials: Section 744-510 recognizes wood, stone, brick, decorative concrete block, wrought iron, products resembling those materials, vegetated cellular confinement systems, other materials compatible with the primary building, and combinations. Fence/wall combinations use this material framework.
• Vinyl/PVC and composite products: Vinyl/PVC and composite fencing are not expressly named as freestanding material categories in the general fence section. Products created to resemble listed materials and materials compatible with the primary building are recognized categories. A vinyl coating is expressly specified for certain chain-link applications, as described below.
• Chain-link/wire — lower-density dwelling contexts: Table 744-510-1 permits chain-link or wire fencing in all yards in D-A, D-S, D-1, D-2, D-3, D-4, D-5, D-5II and D-8 for single-/two-family dwellings. The same table branch includes PK-I, SU-8, SU-43 and SU-46. Yard heights and sight restrictions still apply.
• Chain-link/wire — other dwelling and listed districts: In D-6, D-6II, D-7, other D-8 contexts, D-9, D-10 and D-11, and the table’s hospital, university, PK-II, commercial, Mixed-Use, central-business and listed Special Use districts, chain-link/wire is permitted in side or rear yards with black, brown or dark-green vinyl/equivalent coating and no slats. The listed Special Use districts in this branch are SU-1, SU-2, SU-3, SU-5, SU-6, SU-7, SU-9, SU-34, SU-35, SU-37, SU-38, SU-41, SU-42, SU-44 and SU-45.
• Chain-link/wire — industrial and specified Special Use contexts: Industrial districts permit it in side, rear and front yards. SU-10, SU-13, SU-16, SU-18, SU-23, SU-28 and SU-39 permit side/rear placement and allow front-yard placement with black, brown or dark-green vinyl/equivalent coating. In this table branch, slats are prohibited in a front yard or any transitional yard.
• Speedway Main Street District SZ-1: Fencing materials must complement the primary building’s design. Chain-link, barbed wire and razor wire are prohibited. Applicable site-and-development-plan conditions remain part of the district’s design controls.
• Barbed wire and razor wire: The general metropolitan rule prohibits these materials except for enclosing livestock where the primary property use is agricultural, or for public-safety/security purposes at a public facility or correctional/penal institution. Those exceptions do not describe an ordinary residential privacy fence.
• Electrified livestock fencing: The published exceptions require nonlethal voltage, current below 100 mA (0.1 amp), a conspicuous warning sign and at least five feet from a lot line. The qualifying uses are livestock enclosure on a primarily agricultural site, specified public-facility/correctional security, or personal livestock in a Dwelling district. The general rule otherwise prohibits electrified fencing.
• Scrap and waste materials: Fences, walls and retaining walls cannot use scrap or waste materials unless those materials have been recycled or reprocessed into building materials offered for sale to the public.
• Qualifying agricultural partition-fence construction: For a partition fence within IC 32-26-9’s agricultural-land scope, IC 32-26-9-3 recognizes a lawful partition fence sufficiently tight and strong to hold cattle, hogs, horses, mules and sheep: a four-foot straight board-and-wire, straight wire, straight board or picket fence; a 4.5-foot straight rail fence; or a five-foot worm rail fence. These are the chapter’s livestock-containment specifications. Applicable zoning limits and the chapter’s special watercourse provisions also require review.
• Retaining-wall materials: Retaining walls must be constructed of or faced with natural stone, brick or similar earth-colored materials, decorative concrete block, vegetated cellular confinement systems, textured/colored mechanically stabilized earth blocks, or other material compatible with the primary building. Dwelling-district garden walls 30 inches or lower are exempt from this material standard. Retaining walls made of railroad ties, timber or gabion-type materials are prohibited.
• Retaining-wall terracing: Walls above six feet must be terraced, with no more than three tiers. A terrace at least four feet wide, with a maximum 3:1 slope, is required between tiers. The Administrator may approve reduced terrace depth where site constraints limit space. Terraces require permanent landscaping unless a licensed engineer determines that geologic hazards make the soil unsuitable.
• Town pool enclosure: Chapter 15.29 applies to private household/guest pools of a permanent nature, above or below ground. A nonpermanent pool also qualifies if it is not disassembled or removed for storage during nonuse. The Town requires a child-restraining enclosure at least five feet high, at least four feet from the pool perimeter. Gates/doors must be at least five feet high, equipped with a latch or lock, and close and latch without manual assistance.
• Metropolitan pool/hot-tub provision: Section 743-306.JJ separately specifies either its referenced safety-pool cover or a child-protective fence/structural barrier with a self-closing, self-latching gate. The barrier is at least five feet at grade or 36 inches on a raised deck or the top of an aboveground pool/hot-tub wall; combined pool/barrier height cannot exceed 10 feet. Its perimeter-fence exception removes a separate pool-security fence where the existing fence prevents public entry, unless it is more than 50 feet from the pool/hot tub. The cover cross-reference names the former residential swimming-pool rule.
• Indiana residential-pool access control: Indiana R326 applies to outdoor residential pools capable of a depth greater than 42 inches and all pools inside a residence regardless of depth, when intended for noncommercial use by no more than two owner families and their guests. Artificial lakes are excluded. One method uses walls/fencing at least four feet high, completely surrounding the pool and deck, with self-closing, self-latching, lockable gates/doors. Another uses other means at least four feet high deemed impenetrable by the enforcing authority when constructed; a combination of these methods is also available, with the stated gate/door conditions. The separate power-safety-cover method requires continuous deck connection preventing access when closed, keyed/key-and-switch/personal-code mechanical operation, manufacturer-compliant accessories, and an identification tag showing ASTM F 1346-91 (2018) compliance.
The published Town, metropolitan and state pool provisions are not fully aligned, particularly for safety covers, raised-deck barriers and existing yard fences. Confirm the applicable enclosure design with the Speedway Building Commissioner and Indianapolis Department of Metropolitan Development before relying on one of those alternatives.
• Automatic property-access gates: For property accessed through a gate or crossarm operated by a key or swipe card, Town Section 15.28.060.02.09 requires a Knox key switch keyed to the Town fire department, at a location determined by the fire chief or designee. The provision covers Class 2 access and expressly includes Class 1 structures.
• Chicken coops and runs: If visible to neighboring occupants, the coop and run require a sight fence or shrub screening at least four feet high. Chickens must remain securely enclosed. The combined coop/run area must provide 12 square feet per chicken, be at least 12 feet from a neighboring property line and 20 feet from another owner’s building used or capable of use for human habitation, and meet the published animal-protection and accessory-structure conditions.
• Hazardous residential excavations: Where children regularly play in a residential area, an excavation at least four feet deep maintained more than 30 days must be securely covered or protected by fencing or a similar barricade designed to control children’s entry.
• Maintenance: The Town requires fences and walls associated with dwellings to remain structurally sound, coated where needed to prevent deterioration, and free of electrical/fire hazards and harmful infestation. Metropolitan standards require outdoor fencing to remain safe, serviceable and rust-free; damaged barriers and failing finishes require repair, replacement or refinishing.
PRIVATE RESTRICTIONS
HOA covenants, private subdivision and deed restrictions, architectural-review covenants, private boundary agreements, recorded partition-fence agreements and conservation easements operate independently of public approvals and may be more restrictive. Recorded private easements can also limit fence posts, panels, gates or access. Public subdivision regulations, approved development commitments and public utility/drainage easements have their own legal roles; a public permit exclusion does not release a private restriction or change an easement’s terms.
Under IC 32-26-3-1, adjoining owners who choose a different arrangement from Article 26 for erecting, repairing, maintaining or paying for a fence separating their land must use a written agreement signed by the adjoining owners and recorded with the recorder in the county or counties where the properties lie. A private alternative agreement concerns those owners’ fence responsibilities; applicable public zoning, visibility and safety requirements continue to govern the work.
REVIEW AND ENFORCEMENT CONTEXT
Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:
• Height, materials and placement: Metropolitan zoning standards, yard classifications, corner/through-lot exceptions, SZ-1 restrictions and approved development-plan conditions.
• Town sight-distance complaints: Town departments forward complaints to Police Code Enforcement for inspection under Chapter 10.48. Curb-line triangles, access-point visibility and the metropolitan sight requirements can each affect a fence location.
• Pool enclosure design: The separate Town, metropolitan and state provisions, including gate operation, heights, separation and the unresolved relationship among their alternatives.
• Drainage, easements and flood-hazard development: Recorded access rights, approved plat drainage plans, stormwater-facility maintenance, mapped stream corridors and the applicable floodplain/floodway approvals.
• Property and access maintenance: Structurally unsound or deteriorated fences/walls, qualifying hazardous excavations, chicken-enclosure screening and key-operated property-access gates.
• Adjoining-owner fence duties: Previously unenclosed-property enclosure, joining an existing fence, qualified partition-fence removal and mistaken-boundary removal have their own statutory conditions. Qualifying agricultural partition fences and boundary live-fence complaints have the separate trustee procedures described above.
• Covered excavation: Indiana 811 notice, lawful-start conditions, utility responses, acknowledgment, ticket renewal and protection of marked facilities remain separate from local fence permit exclusions.
USING THIS INFORMATION
This page provides general orientation on how residential fence rules are structured and applied within the Town of Speedway, Indiana. Updated November 2026.
In addition to local fence rules, certain Indiana laws apply statewide. See Statewide Fence Laws in Indiana.
It is not legal advice and does not replace official ordinances, permits, certificates, improvement-location approvals, development approvals, applicable building-code requirements, surveys, or professional guidance. Rules and interpretations may change, and application may vary based on zoning district, plan-commission jurisdiction, county zoning coverage, site conditions, subdivision/land-development status, easements, rights-of-way, floodplain or floodway status, stream conditions, stormwater or drainage requirements, regulated-drain conditions, road or highway conditions, INDOT jurisdiction, historic/design/special-district status, rural or agricultural context, livestock, lawful-fence or agricultural partition-fence context, live-fence or spite-fence conditions, local permit administration, pool-barrier use, Indiana 811 utility-excavation requirements, and private restrictions such as HOA covenants, deed restrictions, private agreements, recorded partition-fence agreements, or conservation easements. Before purchasing materials or beginning construction, confirm current requirements and site-specific limitations with the Speedway Building Commissioner and Indianapolis Department of Metropolitan Development and any applicable private agreements. If this page conflicts with official ordinances, published guidance, adopted district guidelines, or direction from those responsible offices, the official sources control. For legal advice or legal interpretation, consult a licensed attorney.