FENCE RULES – SMITHVILLE (CITY), MISSOURI

OVERVIEW

This guide covers residential property within the incorporated City of Smithville in Clay and Platte Counties, Missouri. County location matters for private wastewater approval; city fence rules apply on both sides of the county line. Updated November 2026.

Smithville allows substantial side- and rear-yard fencing, but street-facing designs receive closer limits. Residential and business district fences may reach 8 feet, while a required decorative front fence is limited to 4 feet and at least 50% openness, or a 3-foot stone or brick wall. A city fence permit is generally required, with an agricultural-district exception. The design also needs to respect street rights-of-way, sight triangles and easement access. Pool barriers have their own detailed construction standards. Repairing or replacing a substantial part of an existing fence can require bringing the entire fence into compliance.

Quick questionSmithville answer
Permit or approvalA city permit and property layout are required for erected fences, except in agricultural districts. The listed fence permit fee is $25.
Typical fence heightUp to 8 feet in residential and business districts. Required decorative front fencing: 4 feet and at least 50% open, or a stone/brick wall up to 3 feet.
Placement & property linesFences must remain at least 1 foot from street rights-of-way and preserve required sight clearance. Side/rear placement also depends on boundaries, easements and special uses.
Common fence materialsWood: recognized. Vinyl/PVC: vinyl is recognized. Chain-link: vinyl-coated chain-link may qualify as decorative; uncoated chain-link does not.
Important local conditionsFence rules may be further affected by multiple street frontages, agricultural zoning, pools, drainage and flood hazards, approved development plans, animal keeping and private restrictions.
Official local resourceSmithville permits and application forms

The table summarizes ordinary fence rules. The sections below explain their applicability, exceptions and site-specific requirements.

GOVERNANCE

• City authority: Smithville is a fourth-class Missouri city spanning Clay and Platte Counties. Its zoning and fence ordinance governs incorporated property. The city separately adopts the 2018 International Residential Code, International Building Code, International Property Maintenance Code and International Swimming Pool and Spa Code, with local amendments. These approval systems have different purposes; an exception in one does not remove a requirement in another.

• Separate responsibilities: The city’s Development Department administers building and fence applications. The City Administrator or designee administers the city’s floodplain program. Private sewage approval follows the health department for the county where the property lies. The June 2025 amendment to section 700.030 uses that county-specific rule, although older city provisions name Clay County alone. Both Clay and Platte operate under local onsite-wastewater ordinances.

• Overlapping requirements: When adopted codes conflict, section 500.010 applies the more restrictive provision; section 400.065 also preserves greater restrictions. A published application handout is useful for administration, but a difference between it and an enacted technical standard needs resolution for the proposed design.

PERMIT AND APPROVAL REQUIREMENTS

• Ordinary fence application: Every erected fence requires a city permit and a general property layout showing its location, except fences in agricultural districts. Smithville deleted the model residential-code exemption for fences not over 7 feet, so that model exemption does not excuse a city fence permit. The currently linked fiscal-year 2026 fee schedule lists a $25 fence permit. Its separate $100 grading fee is not an automatic charge for every fence.

• Plans and submissions: The incidental-construction application calls for a site plan showing buildings, property lines and dimensions, the contractor’s license or application, material-only project valuation and certification by the owner or authorized agent. The city’s separate formal site-plan process applies to new building permits or expanded uses in commercial, industrial and R-3 districts, and conditional uses in any district; façade review is discretionary. An ordinary fence layout is not automatically that professional site-plan submission.

• Who performs the work: Under the contractor ordinance effective October 20, 2026, contractors need the applicable business or occupation license. A homeowner personally occupying and working on the homeowner’s own single-family residence or accessory improvements is excluded from the contractor definition.

• Repair and replacement: Repair or replacement of 15% or more of any portion of an existing fence requires the entire fence to comply with section 400.350. The threshold is not expressed as 15% of total fence length. Smaller repairs still remain subject to applicable permit and maintenance requirements.

• Flood-hazard work: A floodplain permit is required before construction or other development in the city’s designated numbered or unnumbered A and AE flood-hazard areas, with a separate permit for each structure or development. Development includes filling, grading and excavation. The ordinance lists Clay County map panels and future revisions; a Platte-side address alone does not establish that flood requirements are inapplicable. The city’s floodplain administrator determines the applicable parcel and map coverage.

• Pool approval: A pool application must show the house, other buildings, pool, property dimensions and distances, plus barrier and bonding details. Bonding, structural and final inspections are required. Pool use cannot begin until required barriers, alarms, bonding, safety features and inspections are complete. The city pool application supplies these submission and inspection instructions; the design differences described below need separate attention.

• Private wastewater systems: For a private sewage system, the city requires a copy of the approval from the health department for the property’s county before construction. A new building must use an available public sewer or an approved private system. A private-system lot must contain at least 3 acres, unless it is a smaller lot platted before October 20, 1998 and the city finds public connection impractical. Public sewer is considered available within 100 feet of the property line.

• State onsite conditions: Missouri’s onsite exception has a single-family 3-acre branch or a 10-acre residential branch requiring no single-family-residence on-site sewage disposal system within 360 feet of any other on-site sewage disposal system and no more than one single-family residence per 10 acres in aggregate. The exception excludes lots adjacent to a lake operated by the U.S. Army Corps of Engineers or a public utility; all system points must be more than 10 feet from adjoining property lines, with no effluent trespass, contamination or scientifically determined nuisance. More stringent local ordinances remain applicable. State onsite application fees were suspended August 28, 2026 pending new standards; this does not waive Clay or Platte local fees or city and county approvals.

FENCE PLACEMENT RULES

• Boundaries and setbacks: The fence ordinance does not set a general side- or rear-yard setback. Smithville’s general definition of a structure excludes fences, so ordinary building setbacks are not automatically fence setbacks. A fence still must remain within the owner’s rights and comply with street clearances, easements, agricultural-electric setbacks and parcel-specific approvals. A fence or permit does not establish the surveyed boundary.

• Street-facing yards: A fence must be at least 1 foot from every street right-of-way; the right-of-way boundary is not necessarily the curb or pavement edge. A fence may not create a traffic hazard. The front-yard rule covers a yard containing, or abutting an adjacent lot containing, the primary entrance or driveway access or both. A multiple-frontage lot therefore may need decorative front-yard fencing along more than one frontage.

• Parallel double-frontage lots: A limited exception applies to double-frontage lots whose frontages are parallel: nondecorative fencing in an otherwise front-yard area is allowed only when the adjacent lot’s primary entrance is opposite the lot in question. The fence begins at the standard front-yard setback on the adjacent primary-entrance lot and runs straight to no closer than 1 foot from the opposite-side property line. The city’s layout review must resolve that specific geometry; it is not a general corner-lot privacy-fence allowance.

• Public access and easements: Buildings, fences and other obstructions are prohibited in streets, alleys, sidewalks, road rights-of-way and public easements unless an applicable exception authorizes them. A fence permit may allow an easement crossing, but the owner alone pays for repair or replacement when the fence is removed for easement access; the easement user is not responsible for removal damage. Authorized temporary safety fences and barricades for permitted public-way construction remain subject to their safety conditions.

• Drainage: Earth and rubbish must be prevented from washing off a lot onto adjoining streets, sidewalks, public places or waterways. Silt fencing or other erosion controls and otherwise-required permits may be needed. Obstruction of the stormwater system and discharge of pollutants into it are prohibited. Lot grading must prevent erosion and stagnant water; natural streams and waterways and approved retention areas or reservoirs have their stated exceptions. Stagnant water capable of breeding pests is prohibited on lots and in containers.

• Flood flow: Within a designated floodway, fill, construction and other encroachments require hydrologic and hydraulic analysis showing no increase in flood levels. Before a floodway is designated in numbered A or AE areas, cumulative development cannot raise the base-flood surface more than 1 foot. Applicable floodplain development must use flood-resistant materials, adequate anchorage and methods that minimize flood damage.

• Approved developments and overlays: An approved planned-development plan and its supporting documents remain binding. A substantial departure returns to the Planning Commission and Board. The EO 169 South overlay also has separate regulations on file with the city. Existing approved screening and parcel-specific conditions therefore matter when replacing or relocating a residential fence in these areas.

• Survey markers: Except for a registered land surveyor acting under chapter 327, no person may knowingly move, remove, deface or destroy a U.S. Public Land Survey System corner, property-boundary marker, benchmark or horizontal-control monument. Section 60.355 makes a violation a class B misdemeanor and imposes the cost of reestablishment by a registered surveyor. An affected real-estate owner may bring a civil action in the county of the violation; damages under subsection 3 are limited to reasonable surveying costs and reasonable attorneys’ fees.

• Shared boundary fences: Missouri’s partition-fence laws distinguish general and locally adopted systems, with different livestock, contribution, notice, removal and repair procedures. They do not automatically make a neighbor pay half of a chosen privacy fence. A county-specific claim requires the applicable county adoption history and the fence’s facts; the statewide reference explains the separate systems.

• Excavation notice: Before covered excavation, including fence post holes on private property, the excavator must give Missouri One Call notice at least 2 but no more than 10 working days before the expected start and obtain the required facility information. Working days exclude Saturdays, Sundays and legal state or federal holidays. The two-day period begins at midnight following receipt. Agricultural tillage no deeper than 16 inches and marking flags or stakes are limited exceptions, not a fence-post-hole exemption.

• Information for a locate: The notice must identify the excavator by name, address and telephone number and the filer’s name and telephone number if different. It must state the expected start, planned depth, type of excavation, trenchless work and any explosives; email and cell number, if any; and the person primarily responsible, including differing contact information. The notice must also give the detailed location through an accepted address, signed road or street relationship, latitude/longitude or state-plane coordinates; distance and direction from the nearest road or intersection if not already supplied; prominent landmarks; the location within the site by direction and distance from buildings or roads; and access directions when not near a posted road. All required information is needed to complete notice. Physical or electronic white lining can supplement an unclear location. Notice to participating owners goes through the center, subject to statutory clarification and emergency exceptions.

• Private facilities: Not every private service line is included in the statutory locate system. Listed gas, electric, telecommunications/broadband, cable, water, storm-drainage and sewer receiving-service facilities on private property and owned solely by that property’s owner or owners are excluded, except where they cross or lie within an easement or right-of-way dedicated to public use or owned by someone else. That exclusion does not cover vehicular traffic-control, street/highway-lighting or emergency-response-communication lines. Separately, owner-owned water and sanitary-sewer lines serving private property are excluded at any location, as are structures carrying only stormwater under a road, driveway or railway. These exclusions neither promise that private lines will be marked nor authorize damaging them.

• Ticket life and changing marks: A notice expires at 11:59 p.m. 21 consecutive calendar days from the excavator’s intended start date supplied in the notice. Work may continue in the notified area until expiration while marks remain visible. If work cannot begin within 10 working days as described in the request, a relocate request is required before starting. Unusable marks require a remark request in the same manner and time as the original notice. Marks must be preserved with reasonable care; negligent disturbance or repeated unnecessary requests can make the excavator liable for reasonable remarking costs. Only the facility owner or representative marks or relocates it. Discovery of an incorrectly marked or unmarked facility requires notice to the center; the owner must contact the responsible person or correctly locate within 2 hours and correct inaccurate records.

• Responses before digging: An owner or operator ordinarily locates facilities or gives a no-facilities response within 2 working days, unless the excavator agrees through the center to extend the start. Early digging is allowed only when all underground facilities have been confirmed located. Either party may request a marking-clarification meeting within 2 working days. Trenchless-work notice triggers available recorded-depth information. If the location cannot be determined, the excavator must clarify it with white flags or paint, plans or an onsite meeting. A no-facilities response may be given by phone, message, cell, email, clear/OK markings, in person or the locate-status system; when the supplied telephone numbers are the only means of contact, two call attempts suffice.

• No response and emergencies: After a compliant original notice receives no response, a second notice through the center is required before excavation. The owner then has 2 hours to mark or contact the excavator with a marking time. Notice by 2 p.m. requires marking that working day; later notice requires marking by 10 a.m. the next working day. Failure to mark or contact as required permits commencement, but prudent-care duties remain. Genuine emergency excavation may proceed with all reasonable precautions and substantially compliant notice as soon as practical. Notified owners have 2 hours to mark or provide available information and, if marking cannot then occur, say when it will. Excavation in a state highway or its right-of-way separately requires the commission’s permit under section 319.025(4), subject to its railroad-right-of-way exception.

• Care and damage reporting: The approximate facility location generally includes its width plus 2 feet on each side; unusual conditions may require wider markings. Before excavation, the excavator must determine suitable practices for confirming horizontal and vertical location considering geology, access and paving. Hand or soft digging is best practice when possible, and careful, prudent excavation remains mandatory. Damage, dislocation or disturbance must be reported to the center, including damage to trace wires, encasements, cathodic protection or permanent stakes. An immediate call to 911 is required when pipeline damage or contact releases hazardous liquid or gas. Concealing damage or attempting repairs without the owner’s authorization is prohibited, except notified emergency temporary sewer repairs needed to prevent further damage; that exception does not remove the reporting duty.

FENCE HEIGHT AND VISIBILITY RULES

• General height: In residential and business districts, fences may be no higher than 8 feet. This clause does not impose that same cap on agricultural districts. Hedges and shrubs have no height limit under this particular clause, but remain subject to visibility and other applicable restrictions.

• Front-yard height and openness: Where a decorative or ornamental front fence is required, wood, metal, vinyl, vinyl-coated chain-link or a combination may be up to 4 feet high and at least 50% open. A stone or brick wall may be up to 3 feet. Uncoated chain-link, wire, wire mesh, snow fencing and fences made partly from those materials do not qualify as decorative or ornamental.

• Intersection visibility: A material obstruction to vision is prohibited between 2.5 and 8 feet above bottom-of-curb grades within the sight triangle. Its legs are measured from the intersection of street centerlines: 90 feet along each centerline, or 120 feet for major or arterial intersections. Fence rules also protect alley/public-street intersections. The Police Chief or designee determines material obstruction or traffic hazard. One corner-lot provision excepts the central business district, while another applies in any district and the fence provision broadly requires sight clearance; a central-business-district fence therefore needs a specific visibility determination rather than an assumed blanket exception.

MATERIAL AND CONSTRUCTION LIMITS

• Materials and finished side: The Smithville fence ordinance expressly recognizes wood, metal, vinyl and vinyl-coated chain-link in qualifying decorative designs, plus stone and brick walls under the separate 3-foot limit. Uncoated chain-link and other wire products cannot satisfy the decorative-front-fence definition. The structural elements must face the building side, with the finished face toward the neighboring property. Shadow-box construction expressly satisfies that facing rule.

• Barbed wire and electric fences: Hazardous or dangerous designs, barbed wire and electrically charged fencing are prohibited except under the stated agricultural provisions. Barbed wire is permitted in agricultural districts. In Agricultural Zone 1, electric fencing may be installed without a permit, but must remain at least 75 feet from adjacent property in a district where electric fencing is not allowed and at least 5 feet from any other property line.

• Maintenance: Fences and walls must remain structurally sound and in good repair. Wood other than decay-resistant wood requires protective treatment. Peeling or flaking paint must be removed and surfaces repainted; rust or corrosion must be stabilized and coated except where designed oxidation is intended.

• Pool barrier height and openings: The adopted 2018 swimming-pool code requires a barrier top at least 48 inches above outside grade throughout the perimeter and for a 3-foot horizontal area extending outward. Bottom clearance is at most 2 inches over nonsolid ground or 4 inches over a solid surface. A barrier mounted on the pool structure may have no more than 4 inches between the pool-wall top and barrier bottom. Openings cannot pass a 4-inch sphere. Solid barriers cannot provide climbing handholds or footholds beyond normal construction tolerances and tooled masonry joints.

• Mesh pool fencing: Mesh pool fencing must follow the manufacturer’s instructions. Bottom clearance is at most 1 inch; lifting may not exceed 4 inches or permit passage of a 4-inch sphere. An attachment device must connect each mesh barrier section at a height not lower than 45 inches above grade. Where a hinged gate is used, it must meet the gate rules; patio sleeves must be nonconductive, and mesh barriers cannot be mounted on top of onground residential pools.

• Pool horizontal members: Section 305.2.5 requires horizontal members to face the pool when the tops of those members are less than 45 inches apart, with vertical spacing and decorative cutouts no greater than 1¾ inches. Smithville changes only section 305.2.6 to apply when horizontal-member tops are 32 inches or more apart, allowing vertical spacing up to 4 inches and decorative cutouts up to 1¾ inches. Both provisions therefore reach configurations from 32 to less than 45 inches. The city must resolve that overlap for the proposed design under its code-conflict provisions; the unchanged 45-inch clause still matters.

• Pool mesh and clear space: The adopted pool code limits chain-link openings to 1¾ inches unless slats fastened at the top and bottom reduce them to that size or less. Diagonal lattice openings are also limited to 1¾ inches, with diagonal members no more than 45 degrees from vertical. The city pool handout instead gives 1¼-inch opening limits for these two designs. The opening size accepted by Building Inspections needs to be resolved before selecting the fence. A 36-inch clear zone outside the barrier must remain free of climbable permanent structures or equipment, and the pool-water edge must be at least 20 inches inside the barrier.

• Pool gates: Pool gates must meet barrier requirements and accommodate locking. Pedestrian gates open away from the pool and self-close and self-latch; utility or service gates remain locked when not in use. With double gates, one leaf must be fixed in place and the adjacent leaf must self-latch, with no opening greater than ½ inch within 18 inches of the release. When a release is less than 54 inches above grade, it must be on the pool side at least 3 inches below the gate top, with no opening greater than ½ inch within 18 inches of it.

• House walls and safety covers: When a dwelling wall forms part of the barrier, doors and operable windows with sills below 48 inches that give direct pool access need a UL 2017 alarm, a safety cover listed and labeled to ASTM F1346, or an approved equivalent protective means. Alarm deactivation is at least 54 inches high, or 48–54 inches in accessible applications. Separately, section 305.1 excepts barriers under sections 305.2–305.7 for a lockable spa/hot-tub safety cover or a powered pool safety cover complying with ASTM F1346. The existing-pool maintenance rule below has a narrower cover exception.

• Pool walls and alternative barriers: An onground pool wall may serve as a barrier only if it is at least 48 inches high around the full circumference and the manufacturer authorizes that use. A top-mounted barrier must reach at least 48 inches above grade and follow installation instructions. Ladders or steps must be secured, locked or removable, or surrounded by a compliant barrier; resulting openings cannot pass a 4-inch sphere. A shoreline counts only where public access is not permitted, and the barrier must extend at least 18 inches beyond the water. Natural or topographic barriers require equivalent protection accepted by the governing body.

• Existing pool barriers: Under the adopted property-maintenance code, a private pool containing water more than 24 inches deep needs an enclosure at least 48 inches above outside ground. Gates self-close and self-latch from a 6-inch opening. A release less than 54 inches from the gate bottom must be on the pool side. Existing barrier effectiveness cannot be reduced. This rule excepts spas and hot tubs with an ASTM F1346 cover, rather than every covered swimming pool. Its gate-bottom measurement remains separate from the pool code’s grade-based latch measurement.

• Dog enclosures: Dogs may not run at large or be restrained so they can enter another person’s land without permission. On multifamily-type property, animals cannot be leashed, chained, fenced or otherwise restrained in shared common ground. The ordinance has exceptions for customary service-dog use and official government dogs. A dangerous, vicious or ferocious dog must be confined behind an escape-proof fence or enclosure, or on a chain limiting its movement to 10 feet inside the property lines. A Beware of Dog sign with letters at least 2 inches high is required at the confinement area.

• Poultry: Permitted household poultry and animals need secure enclosures and may not roam off the premises. Enclosures must remain in good repair, minimize disruption to neighbors, provide replaceable absorbent ground cover and adequate light and ventilation, and use feeding arrangements that avoid rodents. The residential poultry provision allows up to 10 birds and excludes a rooster, defined as a male chicken over 4 months old. It specifies housing 50 feet from the nearest occupied or habitable building on adjoining land, but includes the unclear parenthetical “no chickens”; the city’s animal-permit review must resolve its application to a chicken enclosure. The agricultural exception expressly concerns quantity, not a blanket setback waiver. The annual poultry permit is $30 and due by September 1.

• Other animals and livestock: Exotic or dangerous wild animals may not be kept in any enclosure unless the caretaker is registered with Missouri for temporary care of injured or sick animals and the land is properly zoned. Separately, owners or persons in charge of cattle, swine, horses, mules, asses, sheep or goats may not allow them outside their enclosure. Others may restrain them, and officers must do so. A known owner must receive written notice within 3 days; actual damages and reasonable taking-up, feeding and keeping costs apply. In a public-highway accident, the owner may establish the statutory no-fault or no-negligence defense.

• Lagoon fencing: Where Missouri’s onsite-lagoon construction standard applies, the lagoon fence must be at least 4 feet high and use welded, woven or chain-link wire no smaller than fourteen gauge. Specified cattle or hog panels with T-posts may be used. Posts are treated wood or galvanized or painted steel, driven, tamped or set in concrete. Line posts may be no more than 10 feet apart, corners require bracing, and the fence must be sound with no gaps or openings along the bottom. Recommended embedments are 18 inches for line posts and 24 inches for corner posts.

• Lagoon position and gate: The lagoon fence may be no closer to the water than the center of the berm at the 3-foot operating-water level. A setback of no more than 30 feet from the water is recommended. The gate must be at least 4 feet high, made of comparable material, hinged and latching; a width of 36–48 inches is recommended. The fence must be installed before occupancy. Local approval may impose more stringent requirements.

• Licensed family day care: At an actual licensed family day care home, the outdoor play area must be safely accessible and fenced when necessary to protect children from traffic, water or other hazards. For homes initially licensed after the rules’ effective date, or new fences at existing facilities, the fence must be at least 42 inches high. Fences must prevent children from crawling or falling through or becoming entrapped. Swimming and wading pools must be fenced against child access; for the initial-license cohort the fence must be at least 42 inches with a locked gate. An aboveground pool may have a 42-inch fence around its top with barricaded steps. These requirements operate alongside the city’s separate pool rules. Animals threatening children’s health or safety must be absent or securely penned away from children, with pens kept clean.

• Family burial grounds: Knowingly injuring or removing the fence around a protected abandoned family or private burial ground is a class A misdemeanor. The protected category is a site not deeded to the public with no interment for at least 25 years. A landlocked site without public ingress or egress carries reasonable-hours visitation access for ordinary cemetery purposes, enforced by the county sheriff or chief law-enforcement officer.

• State-park boundary projects: For a true common boundary with a state park or historic site needing livestock or commercial-game exclusion, written request and director approval precede state participation. Inspection considers need, resources, materials, cost and location; a required boundary survey is shared equally and a written decision is due within 60 days. The division supplies materials, while the owner constructs and maintains the fence. It must follow the verified boundary unless a written variance allows otherwise, without resource damage or grade changes draining wetlands or impounding water on park land.

• State-park boundary maintenance: Within that boundary program, brush, vine and regrowth maintenance may extend no more than 3 feet onto the park side. Vehicles, equipment and herbicides affecting park vegetation need facility-manager permission. Overhanging branches may be trimmed at the boundary up to 8 feet above ground. Removal requires written division consent except for temporary repairs. Participation is unavailable for poisonous crops, the specified saltpeter works or cotton gins, or costs another law or judgment already imposes on the owner.

PRIVATE RESTRICTIONS

• Recorded and agreed restrictions: City fence rules and private restrictions operate separately. Homeowners-association requirements, recorded covenants, private easements and boundary or maintenance agreements can limit a fence beyond government rules; the city ordinance does not annul them. Greater city restrictions still govern. Government approval does not determine ownership, establish an easement’s private scope or allocate a neighbor’s costs.

REVIEW AND ENFORCEMENT CONTEXT

Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:

• Permit and replacement work: A new fence layout, contractor licensing where applicable, and an existing-fence repair that triggers full compliance.

• Street and site conditions: Front-yard design, traffic visibility, public-easement access, drainage, floodplain effects and conditions of an approved development.

• Safety and maintenance: Pool barriers and gates, structurally unsound fencing, animal confinement and applicable household special uses.

• Private disputes: Covenant, ownership, easement and shared-cost questions follow the relevant private rights and legal procedures, separately from city approval.

USING THIS INFORMATION

This page provides general orientation on how residential fence rules are structured and applied within the incorporated City of Smithville, Missouri. Updated November 2026.

In addition to local fence rules, certain Missouri laws apply statewide. See Statewide Fence Laws in Missouri.

It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with the identified municipality, including its actual municipal or county class, charter, adopted program or special district, and each function’s verified territory, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Missouri law. Applicable requirements depend on the property’s actual facts and the respective authority of the identified offices. Private agreements and recorded rights remain separate from government approvals. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern.