FENCE RULES – EXCELSIOR SPRINGS (CITY), MISSOURI
OVERVIEW
This guide covers residential property within the incorporated City of Excelsior Springs in Clay and Ray Counties, Missouri. A mailing address or county location alone does not establish that a property is inside the city. Updated November 2026.
Excelsior Springs distinguishes the front, side and rear yard: the residential fence limits are 4, 6 and 8 feet respectively, with front fencing at least 50% open. Wood and chain-link are listed materials, while vinyl needs a specific approval determination and is prohibited by the historic design guidance. Two practical issues deserve early attention: the city brochure differs from the adopted code on permits for fences between 6 and 7 feet, and it lists a lower rear-yard height than the zoning ordinance. Historic properties, corner visibility, stream buffers and pools add requirements beyond the ordinary yard rules.
| Quick question | Excelsior Springs answer |
|---|---|
| Permit or approval | The city guidance requires a permit above 6 feet; the adopted residential code exempts fences not over 7 feet. Community Development must resolve the permit decision for a 6–7-foot proposal. |
| Typical fence height | Residential front: 4 feet and at least 50% open. Side: 6 feet. Rear: 8 feet under the ordinance; city guidance requires engineering above 6 feet and lists a conflicting rear limit. |
| Placement & property lines | Yard classification, sight triangles, public rights-of-way, utility easements and stream buffers control placement. The fence clauses do not give a universal property-line setback. |
| Common fence materials | Wood: listed, subject to design limits. Vinyl/PVC: not in the ordinary fence list; specific approval needed. Chain-link: listed. Historic guidance prohibits vinyl and chain-link. |
| Important local conditions | Fence rules may be further affected by historic designation, corner or through-lot geometry, pools, stream buffers, flood hazards, animal enclosures, onsite systems and private restrictions. |
| Official local resource | Excelsior Springs fence application guide |
The table summarizes ordinary fence rules. The sections below explain their applicability, exceptions and site-specific requirements.
GOVERNANCE
• City and county scope: Excelsior Springs is a third-class city with council-manager government, occupying parts of Clay and Ray Counties. Its fence and zoning administration covers incorporated territory in both. Community Development administers the local building and land-use approval route, with the Building Official responsible for applicable code decisions and the Community Development Director administering floodplain requirements.
• Construction-code framework: The city adopts the 2018 International Residential and Building Codes, the 2018 International Swimming Pool and Spa Code through section 545.050, and the 2018 International Property Maintenance Code through section 510.010. Local provisions and amendments remain applicable, with the more restrictive provisions controlling conflicts. Historic review, road permissions and wastewater approvals remain separate from an ordinary fence permit.
PERMIT AND APPROVAL REQUIREMENTS
• Fence permit threshold: The city’s current fence guide and inspection information say a building permit is required for a fence taller than 6 feet. The adopted 2018 residential code, section R105.2(2), exempts fences not over 7 feet, without a listed local amendment changing that item. A proposal between 6 and 7 feet therefore needs Community Development’s permit determination before work. The exemption does not waive zoning, historic or other applicable requirements.
• Application and start of work: A required building-code permit must be obtained before work. The local commencement provision for new buildings and structures uses the pouring of footings; starting without the required permit doubles the permit fee. The fence application needs a scale plot plan showing property lines, existing and proposed structures, dimensions, setbacks, utility easements and rights-of-way. Accurate hand drawings are accepted. Staff may request further information, and the guide says to allow up to two weeks.
• Fees, inspection and taller designs: Fees and applicable plan or third-party review charges follow Title I, Appendix A rather than a single published flat fence charge. Inspections require 24 hours’ notice, and the permit must remain posted until final approval. The fence guide requires engineering for a fence exceeding 6 feet; it also lists 6 feet for rear fencing, while the ordinance allows 8 feet. Community Development’s review must resolve the proposed rear-yard design, engineering and permit requirements together.
• Existing fences: Lawfully existing nonconforming structures may continue under section 400.050. The Building Official determines what constitutes ordinary repair; alterations to a structure nonconforming only as to height or yard must meet current standards. Casualty damage not exceeding 50% of true current value may be restored within 12 months, excluding litigation time; greater damage requires conformity. Lawful height- or yard-only structures are excepted from the unused-building provision’s 180-day discontinuance rule. These protections do not legalize a fence that was unlawful when built.
• Historic approval: A designated landmark or property in a historic district needs a Certificate of Appropriateness before exterior-affecting construction, alteration, removal or work on significant exterior features. The certificate precedes any building permit and can be required even when a building permit is not. The city provides for issuance or denial within 45 days and a city-determined emergency waiver. Ordinary maintenance without a material change is distinguished from alteration; replacing a fence is not automatically ordinary maintenance.
• Historic project changes: The city Certificate of Appropriateness process provides current filing deadlines and reviewer assignment. A certificate is valid for 12 months and only for the reviewed project. Changes must be brought back for review or notice before work, and an appeal must be filed within 30 days.
• Public-way approval: Excavation in, through or under a street, sidewalk, alley or other public place requires a right-of-way permit. So does a fixed structure, material or object in, under, on, through or above the right-of-way. Construction that obstructs free passage or surface-water flow cannot receive that permit. A yard-fence permit alone does not authorize public-right-of-way use.
• Land disturbance: Minor construction disturbing no more than one acre is exempt from the city stormwater process only if the Director determines it neither substantially changes the lay of the land nor increases impervious surface by more than 10%. Exclusive agriculture or silviculture, stated emergency work and limited linear projects have separate conditional exemptions. Nonexempt work below one acre needs a sketch plan; work of one acre or more needs a stormwater management plan.
• Floodplain permits: Each construction or development project in the designated flood areas needs a separate floodplain permit. The Community Development Director determines the applicable parcel coverage. The ordinance’s map-panel list names Clay County panels and future revisions; a Ray County location does not itself exempt property from known flood-hazard requirements.
• Pool projects: Constructing, altering, repairing, removing or demolishing a pool requires a building permit. A qualified licensed journeyman performs the plumbing work. Applications include plans and specifications, filter, piping, pump and waste information, and a plot plan; the official may waive plans for minor work. The project must be completed within one year, with reasonable extensions no longer than 90 days each. Excavations must be protected during rain and work stoppages.
• Private wastewater approval: Private sewage construction requires the city building permit and the onsite permit through the health department for the county where the system lies before work begins. Clay County Public Health Center operates under local ordinance authority. For incorporated Ray County, the Ray County Health Department is the contract authority; Ray Planning and Zoning’s ordinance program serves unincorporated areas. City inspection occurs before covering the work, within 48 hours of notice. Applicable city, county and state requirements remain.
• Wastewater lot and connection rules: A subsurface-soil-absorption system cannot serve a new building permit on a lot under 20,000 square feet. The general sewer-connection provision uses availability within 300 feet of the property line, measured along a street, alley or easement to the sewer-easement edge, and a 180-day notice period. The existing-private-system provision separately uses 90 days when sewer becomes available. Septic or cesspool discharge to a natural outlet is prohibited.
• Existing-system connection exception: An existing system may avoid mandatory connection only when it creates no nuisance or hazard, has no surfacing or discharge failure, meets county and state requirements, receives a licensed inspection and report upon sale or transfer, and pays the monthly city sewer base charge. Additional county requirements remain applicable.
• State onsite conditions: Missouri’s onsite exception has a single-family 3-acre branch or a 10-acre residential branch requiring no single-family-residence on-site sewage disposal system within 360 feet of any other on-site sewage disposal system and no more than one single-family residence per 10 acres in aggregate. The exception excludes lots adjacent to a lake operated by the U.S. Army Corps of Engineers or a public utility; all system points must be more than 10 feet from adjoining property lines, with no effluent trespass, contamination or scientifically determined nuisance. More stringent local ordinances remain applicable. State onsite application fees were suspended August 28, 2026 pending new standards; this does not waive Clay or Ray local fees or city and county approvals.
• Other approval paths: Single- and two-family dwellings are excluded from the formal site-plan process in section 400.225 and landscape-plan rule in section 400.290, while their actual special-use or planned-development conditions remain binding. The city may grant modifications of 10% or less to listed standards only with the required findings and written record. This is discretionary approval, not an automatic fence-height bonus. A disability-related reasonable-accommodation application under section 404.015 proceeds through recommendation and Council decision; submissions may become public records.
FENCE PLACEMENT RULES
• Which yard faces the street: The front yard extends across the lot from the front lot line to the main building’s front; the rear yard lies across the lot behind the principal building, and side yards lie between those yards. A corner lot fronts the street of least dimension unless the Building Official specifies otherwise. A through lot ending at a limited-access highway with no lot access fronts the street that provides access. These classifications determine which fence rule applies.
• Property lines: The fence provisions allow fencing in front, side and rear yards under their stated limits and do not establish a separate universal property-line setback. Garage and accessory-building setbacks are not automatically fence setbacks. Boundaries, easements, sight clearance, stream buffers, rights-of-way, historic review and permit conditions still govern the location. A permit gives no right to enter or alter someone else’s property.
• Utility access: Permanent subdivision utility easements must remain open for maintenance and cannot be obstructed by fences, structures or landscaping. Where alleys are absent, the rule provides at least 10 feet on each side of rear lines and necessary alternating side lines, creating a continuous 20-foot corridor. The recorded plat determines its location; these widths are not automatic setbacks from every property line. Added overburden that changes utility depth needs Public Works approval.
• Roadside work and drainage: Permitted public-way excavation requires minimal surface injury and inconvenience, maintained gutter flow, notice to Public Works at least 8 hours before refilling, surface restoration, debris removal, and barricades and lighting for hazards. Excavating machines may not operate in a street or dedicated right-of-way on Sundays or holidays except for an authorized emergency. Damming, stopping, damaging or interfering with city-established sewer pipes, drains, gutters, culverts or natural drainage serving streets, alleys and other public grounds is prohibited. Adjacent sidewalks and rights-of-way must remain free of litter and construction debris.
• Stream buffers: Streams with tributary areas greater than 40 acres require buffers under the Kansas City area American Public Works Association section 5600 standards. The buffer begins at the ordinary high-water mark; adjoining wetlands are added, with a 15-foot buffer around wetland edges outside the stream buffer. Public Works may adjust widths for local conditions. The actual buffer is delineated on surveys, plats or development plans. The additional 10-foot building setback is separate from fence placement.
• Fences within buffers: Within a regulated stream buffer, walls, solid fences, chain-link and woven- or welded-wire fences are prohibited unless incidental to an allowed use. Clearing, grading, filling and drainage changes are also restricted. Allowed uses include approved flood or stormwater facilities, utility crossings, permeable paths, road crossings, necessary utilities and approved restoration. City review applies to maintenance or restoration; an open design is not by itself permission to build in the buffer.
• Flood flow and construction: Floodway encroachments need a registered engineer’s or architect’s certification of no increase in flood levels. Before a floodway is designated, cumulative development cannot increase the 100-year flood elevation more than one foot at the specified average cross-section. Applicable work must be anchored and designed against flotation, collapse and lateral movement, with flood-resistant materials and required drainage and utility safeguards.
• Survey markers: Except for a registered land surveyor acting under chapter 327, no person may knowingly move, remove, deface or destroy a U.S. Public Land Survey System corner, property-boundary marker, benchmark or horizontal-control monument. Section 60.355 makes a violation a class B misdemeanor and imposes the cost of reestablishment by a registered surveyor. An affected real-estate owner may bring a civil action in the county of the violation; damages under subsection 3 are limited to reasonable surveying costs and reasonable attorneys’ fees.
• Shared boundary fences: Missouri’s partition-fence laws distinguish general and locally adopted systems, with different livestock, contribution, notice, removal and repair procedures. They do not automatically make a neighbor pay half of a chosen privacy fence. A county-specific claim requires the applicable county adoption history and the fence’s facts; the statewide reference explains the separate systems.
• Excavation notice: Before covered excavation, including fence post holes on private property, the excavator must give Missouri One Call notice at least 2 but no more than 10 working days before the expected start and obtain the required facility information. Working days exclude Saturdays, Sundays and legal state or federal holidays. The two-day period begins at midnight following receipt. Agricultural tillage no deeper than 16 inches and marking flags or stakes are limited exceptions, not a fence-post-hole exemption.
• Information for a locate: The notice must identify the excavator by name, address and telephone number and the filer’s name and telephone number if different. It must state the expected start, planned depth, type of excavation, trenchless work and any explosives; email and cell number, if any; and the person primarily responsible, including differing contact information. The notice must also give the detailed location through an accepted address, signed road or street relationship, latitude/longitude or state-plane coordinates; distance and direction from the nearest road or intersection if not already supplied; prominent landmarks; the location within the site by direction and distance from buildings or roads; and access directions when not near a posted road. All required information is needed to complete notice. Physical or electronic white lining can supplement an unclear location. Notice to participating owners goes through the center, subject to statutory clarification and emergency exceptions.
• Private facilities: Not every private service line is included in the statutory locate system. Listed gas, electric, telecommunications/broadband, cable, water, storm-drainage and sewer receiving-service facilities on private property and owned solely by that property’s owner or owners are excluded, except where they cross or lie within an easement or right-of-way dedicated to public use or owned by someone else. That exclusion does not cover vehicular traffic-control, street/highway-lighting or emergency-response-communication lines. Separately, owner-owned water and sanitary-sewer lines serving private property are excluded at any location, as are structures carrying only stormwater under a road, driveway or railway. These exclusions neither promise that private lines will be marked nor authorize damaging them.
• Ticket life and changing marks: A notice expires at 11:59 p.m. 21 consecutive calendar days from the excavator’s intended start date supplied in the notice. Work may continue in the notified area until expiration while marks remain visible. If work cannot begin within 10 working days as described in the request, a relocate request is required before starting. Unusable marks require a remark request in the same manner and time as the original notice. Marks must be preserved with reasonable care; negligent disturbance or repeated unnecessary requests can make the excavator liable for reasonable remarking costs. Only the facility owner or representative marks or relocates it. Discovery of an incorrectly marked or unmarked facility requires notice to the center; the owner must contact the responsible person or correctly locate within 2 hours and correct inaccurate records.
• Responses before digging: An owner or operator ordinarily locates facilities or gives a no-facilities response within 2 working days, unless the excavator agrees through the center to extend the start. Early digging is allowed only when all underground facilities have been confirmed located. Either party may request a marking-clarification meeting within 2 working days. Trenchless-work notice triggers available recorded-depth information. If the location cannot be determined, the excavator must clarify it with white flags or paint, plans or an onsite meeting. A no-facilities response may be given by phone, message, cell, email, clear/OK markings, in person or the locate-status system; when the supplied telephone numbers are the only means of contact, two call attempts suffice.
• No response and emergencies: After a compliant original notice receives no response, a second notice through the center is required before excavation. The owner then has 2 hours to mark or contact the excavator with a marking time. Notice by 2 p.m. requires marking that working day; later notice requires marking by 10 a.m. the next working day. Failure to mark or contact as required permits commencement, but prudent-care duties remain. Genuine emergency excavation may proceed with all reasonable precautions and substantially compliant notice as soon as practical. Notified owners have 2 hours to mark or provide available information and, if marking cannot then occur, say when it will. Excavation in a state highway or its right-of-way separately requires the commission’s permit under section 319.025(4), subject to its railroad-right-of-way exception.
• Care and damage reporting: The approximate facility location generally includes its width plus 2 feet on each side; unusual conditions may require wider markings. Before excavation, the excavator must determine suitable practices for confirming horizontal and vertical location considering geology, access and paving. Hand or soft digging is best practice when possible, and careful, prudent excavation remains mandatory. Damage, dislocation or disturbance must be reported to the center, including damage to trace wires, encasements, cathodic protection or permanent stakes. An immediate call to 911 is required when pipeline damage or contact releases hazardous liquid or gas. Concealing damage or attempting repairs without the owner’s authorization is prohibited, except notified emergency temporary sewer repairs needed to prevent further damage; that exception does not remove the reporting duty.
FENCE HEIGHT AND VISIBILITY RULES
• Residential yard heights: Residential front-yard fences may be no higher than 4 feet and must be at least 50% open or perforated over the entire surface. Side-yard fences may be up to 6 feet. Rear-yard fences may be solid or perforated and up to 8 feet under the zoning ordinance, subject to the taller-design review described above. The provisions sit within the A, R-1, R-1A and R-2 accessory rules and apply to single- and two-family dwellings in R-3, R-4 and R-5 through section 400.240(D).
• Height measurement: A structure other than a building is measured vertically from average ground level at its base to its highest part. The roadway measurement used for sight clearance and the outside-grade measurements used for pool barriers remain separate.
• Corner visibility: On corner lots, sight triangles extend in each vehicle-approach direction, using a short leg of 20 feet and a long leg of 140 feet along the curb line or pavement edge. No shrubbery, fence or other vision obstruction over 2 feet above the roadway may occupy that area. R-1A lots at a four-way-stop intersection have a stated exception. The operative geometry is in section 400.270(C)(7), despite the fence clause’s internal reference to section 400.240.
• Restricted-area vegetation: A separate provision limits plants, hedges, shrubs and other growth except trees in a “restricted area” to 2 feet measured from the street gutter flow line. The city must identify the restricted area applicable to the property; this wording does not impose a two-foot cap on every yard or replace the zoning sight triangle.
MATERIAL AND CONSTRUCTION LIMITS
• Ordinary materials: The residential fence provisions list wood, chain-link, iron or split-rail types for front yards; side and rear lists specify wood, chain-link, wrought iron or split rail. Front-yard openness and the respective yard heights remain mandatory. Vinyl/PVC is not on the ordinary list, so a proposed vinyl design needs a specific city approval determination. Historic and stream-buffer restrictions can further limit a listed material.
• Safety and maintenance: A fence wholly or partly made of barbed wire on the line of or adjacent to a street, alley, sidewalk or other public place is a nuisance. This location-specific provision is separate from agricultural interior fencing. Fences, retaining walls and other accessory structures must remain structurally sound and in good repair.
• Historic fence character: On historic properties, original or significant fences, walls, sidewalks and trees are to be preserved, and new elements must be compatible with adjacent façades and the historic period. The city’s historic design guidance prohibits tall fences that block front views, recommends ornamental fencing no higher than 2½ feet, and may allow rear privacy screening of objectionable views. The 2½-foot wording is a recommendation within historic review, not the general citywide maximum.
• Historic materials: New historic-district wood fencing should complement the building and have paint or opaque stain. Modern patterns including basketweave, “stockage,” split rail and board-on-board are not allowed by the guidance. Metal chain-link and vinyl are prohibited. Wood-like composite or synthetic material may be considered case by case; a simple metal pattern is recommended where historical precedent is unavailable. Ornamental-shrub fences must be neatly pruned.
• Historic retaining walls: Historic stone retaining walls should be maintained and repointed, or checked for stability and restacked. New retaining walls should follow the historic line, setback, style, materials and detail; the guidance discourages wood planks, chain-link metal, split-face pavers and concrete masonry units.
• Local pool enclosure: Chapter 545 defines a swimming pool as at least 24 inches deep or more than 200 square feet in surface area. Its wading-container provision separately addresses containers not over 24 inches deep with volume exceeding 675 cubic feet. The local barrier rule independently applies when water is 24 inches or more at any point. Enclosure and gates must be at least 4 feet above underlying ground and prevent access by small children. Gates must self-latch, with the latch at least 4 feet above ground or inaccessible to a small child from outside. The Building Official may approve a natural barrier, hedge, cover or other device only if it provides at least equivalent protection.
• Pool placement: A pool or auxiliary building must be at least 10 feet from side and rear lot lines; on a corner lot it must be at least 15 feet from the side street and 20 feet from an adjoining principal building. No pool may extend forward of the front building line. A side-yard pool must be at least 60 feet from the front line and 15 feet from the side line. These are pool-location requirements rather than ordinary fence setbacks.
• Overlapping pool standards: The independently adopted 2018 swimming-pool code adds the following barrier standards. The local pool enclosure rule and the more-restrictive conflict provision remain applicable; a model-code cover option does not automatically waive the local requirement.
• Pool barrier height and openings: The adopted 2018 swimming-pool code requires a barrier top at least 48 inches above outside grade throughout the perimeter and for a 3-foot horizontal area extending outward. Bottom clearance is at most 2 inches over nonsolid ground or 4 inches over a solid surface. A barrier mounted on the pool structure may have no more than 4 inches between the pool-wall top and barrier bottom. Openings cannot pass a 4-inch sphere. Solid barriers cannot provide climbing handholds or footholds beyond normal construction tolerances and tooled masonry joints.
• Mesh pool fencing: Mesh pool fencing must follow the manufacturer’s instructions. Bottom clearance is at most 1 inch; lifting may not exceed 4 inches or permit passage of a 4-inch sphere. An attachment device must connect each mesh barrier section at a height not lower than 45 inches above grade. Where a hinged gate is used, it must meet the gate rules; patio sleeves must be nonconductive, and mesh barriers cannot be mounted on top of onground residential pools.
• Pool horizontal members: When the tops of horizontal members are less than 45 inches apart, those members must face the pool, and vertical spacing and decorative cutouts may be no greater than 1¾ inches. When the tops are 45 inches or more apart, vertical spacing may be up to 4 inches, with decorative cutouts still limited to 1¾ inches.
• Pool mesh and clear space: Chain-link openings may be no larger than 1¾ inches unless slats fastened at the top and bottom reduce them to that size or less. Diagonal lattice openings are limited to 1¾ inches, and diagonal members may be no more than 45 degrees from vertical. A 36-inch exterior clear zone must remain free of climbable permanent structures and equipment. The pool-water edge must be at least 20 inches inside the barrier.
• Pool gates: Pool gates must meet barrier requirements and accommodate locking. Pedestrian gates open away from the pool and self-close and self-latch; utility or service gates remain locked when not in use. With double gates, one leaf must be fixed in place and the adjacent leaf must self-latch, with no opening greater than ½ inch within 18 inches of the release. When a release is less than 54 inches above grade, it must be on the pool side at least 3 inches below the gate top, with no opening greater than ½ inch within 18 inches of it.
• House walls and safety covers: When a dwelling wall forms part of the barrier, doors and operable windows with sills below 48 inches that give direct pool access need a UL 2017 alarm, a safety cover listed and labeled to ASTM F1346, or an approved equivalent protective means. Alarm deactivation is at least 54 inches high, or 48–54 inches in accessible applications. Separately, section 305.1 excepts barriers under sections 305.2–305.7 for a lockable spa/hot-tub safety cover or a powered pool safety cover complying with ASTM F1346. The existing-pool maintenance rule below has a narrower cover exception.
• Pool walls and alternative barriers: An onground pool wall may serve as a barrier only if it is at least 48 inches high around the full circumference and the manufacturer authorizes that use. A top-mounted barrier must reach at least 48 inches above grade and follow installation instructions. Ladders or steps must be secured, locked or removable, or surrounded by a compliant barrier; resulting openings cannot pass a 4-inch sphere. A shoreline counts only where public access is not permitted, and the barrier must extend at least 18 inches beyond the water. Natural or topographic barriers require equivalent protection accepted by the governing body.
• Existing pool barriers: Under the adopted property-maintenance code, a private pool containing water more than 24 inches deep needs an enclosure at least 48 inches above outside ground. Gates self-close and self-latch from a 6-inch opening. A release less than 54 inches from the gate bottom must be on the pool side. Existing barrier effectiveness cannot be reduced. This rule excepts spas and hot tubs with an ASTM F1346 cover, rather than every covered swimming pool. Its gate-bottom measurement remains separate from the pool code’s grade-based latch measurement.
• Dog confinement: Dogs and miniature pigs may not run at large; a suitable escape-preventing fence can provide physical restraint. Customary seeing-eye use and official government-dog use are excepted. A declared dangerous dog must be secured inside the residence or in a locked enclosure preventing both escape and child entry and providing shelter, exercise, light and ventilation. The construction provision calls for secure sides and a top, or sides at least 6 feet high, with the bottom attached or the sides embedded at least 1 foot. The separate enclosure definition also requires at least 6 feet, so a shorter roofed pen is not an established exception.
• Dangerous-dog conditions: Outside the enclosure, a declared dangerous dog is allowed only under the prescribed veterinary or exercise circumstances, muzzled and on a leash no longer than 4 feet held by a capable adult over 18. A prominent Beware of Dog sign is required; an unsecured porch or patio is not adequate confinement. Escape or a bite requires immediate notice. Dangerous-dog permits, licensing and possible minimum $100,000 liability coverage are additional conditions. Vicious dogs are prohibited, and separate rules restrict dangerous nondog animals and specified wild animals in residential areas.
• Livestock enclosures: Lawful livestock must be restrained against escape, with gates closed by chain and padlock. Ordinary livestock keeping is normally limited to two animals and located 150 feet from the nearest human-used building other than the keeper’s dwelling. The agricultural branch allows at most two animals at the property line, keeps their concentration 150 feet away and limits density to one animal per 2 acres. Pigs and hogs other than domestic miniature pigs are prohibited. Stables, coops and pens must also satisfy zoning.
• Backyard chicken permits and numbers: Backyard hens require an annual Police Chief permit, inspection and use at the keeper’s principal residence; a renter needs written owner permission. The detached-house property must have at least 8,712 square feet. The printed tiers allow three hens on 8,712–21,344 square feet, six on 21,780–43,124 square feet, twelve on 1–2.99 acres and twelve on more than 3 acres. For a lot in a gap between those ranges, including exactly 3 acres, the permit decision must establish the allowed number. Agricultural use follows the separate rule below. Roosters and other fowl are excluded from this backyard-hen permission, keeping is noncommercial, and live slaughter is prohibited.
• Chicken location and restraint: The coop or pen belongs only in a fenced rear yard, at least 10 feet from rear-yard property lines. The separate 150-foot separation runs from the nearest human-occupied building other than the keeper’s dwelling to the nearest point of the property where chickens are kept, not merely to the coop. During daylight, hens may leave the pen only within a securely fenced rear yard under an adult’s visual supervision; otherwise they must stay secured in the coop or pen.
• Chicken enclosure construction: A chicken coop must be enclosed on all sides with a roof and doors lockable at night. Vents and windows need predator- and bird-proof wire with openings smaller than one inch. The pen uses sturdy wire with a wire, aviary-netting or solid roof. Materials must be uniform and moisture-resistant; scrap or waste boards, sheet metal and similar materials are prohibited. The finish must be maintained, and the enclosure must remain dry, sanitary, predator- and rodent-proof. Floor area must be at least 10 and no more than 20 square feet per chicken; interior roosting height is at least 2 feet and exterior coop height, including risers or pedestals, is at most 10 feet. Enclosed manure storage is limited to 3 cubic feet, with required cleanup, odor and feed controls.
• Agricultural small-animal enclosures: For the agricultural small-animal rule, the livestock or poultry area must be within an ownership of at least 5 acres principally used for row crops or grazing. Section 210.130 requires an all-sided enclosure and prohibits running or flying at large except for homing pigeons. Its location sentence includes a 150-foot human-building separation and a 25-foot property-line/commercial qualification whose application needs a city determination; it is not a general yard-fence setback. Enclosures must remain dry and sanitary, and manure must be kept in covered watertight, flytight receptacles. Removed manure must be buried under at least 6 inches of earth, thoroughly spaded into soil as fertilizer or removed from the premises. Earthen fowl runs must be spaded and limed every 3 months from April through December. No crowing rooster may be within 300 feet of another residence.
• Separate small-animal quantity limits: Section 210.130 also has a nonagricultural quantity clause tied to 150 feet: twelve fowl aged 4 months or more or thirty under 4 months, and ten small animals over 4 months or twenty under 4 months, with stated trade, laboratory and agricultural exceptions. It does not authorize an otherwise prohibited use or displace the separate nonagricultural backyard-chicken permit rules.
• Compost enclosures: Home compost must be enclosed in the rear yard, at least 10 feet from buildings and 5 feet from lot lines. Maximum size is 125 cubic feet and 5 feet high; one pile is allowed on premises up to one acre and two above one acre. Woven wire, wood, cement block, brick or a commercial bin may be used. Animal fats are prohibited, and the pile must be aerated and managed against odors. Community Development may approve reasonable alternatives.
• Vehicle screening: The open-storage rule for inoperable or unlicensed vehicles has an exception for a vehicle completely inside a locked building or a locked fenced area and invisible from adjacent public and private property. Other zoning rules remain applicable; screening alone is not general authorization for vehicle or junk storage.
• Livestock restraint: Owners or persons in charge may not allow cattle, swine, horses, mules, asses, sheep or goats outside their enclosure. Others may restrain them and officers must do so. A known owner receives written notice within 3 days. Actual damages and reasonable taking-up, feeding and keeping costs apply. For a public-highway accident, the owner may establish the statutory no-fault or no-negligence defense.
• Lagoon fencing: Where Missouri’s onsite-lagoon construction standard applies, the lagoon fence must be at least 4 feet high and use welded, woven or chain-link wire no smaller than fourteen gauge. Specified cattle or hog panels with T-posts may be used. Posts are treated wood or galvanized or painted steel, driven, tamped or set in concrete. Line posts may be no more than 10 feet apart, corners require bracing, and the fence must be sound with no gaps or openings along the bottom. Recommended embedments are 18 inches for line posts and 24 inches for corner posts.
• Lagoon position and gate: The lagoon fence may be no closer to the water than the center of the berm at the 3-foot operating-water level. A setback of no more than 30 feet from the water is recommended. The gate must be at least 4 feet high, made of comparable material, hinged and latching; a width of 36–48 inches is recommended. The fence must be installed before occupancy. Local approval may impose more stringent requirements.
• Licensed family day care: At a licensed family day care home, the outdoor play area must be safely accessible and fenced when necessary to protect children from traffic, water or other hazards. For homes initially licensed after the rules’ effective date, or new fences at existing facilities, the fence must be at least 42 inches high. Fences must prevent children from crawling or falling through or becoming entrapped. Swimming and wading pools must be fenced against child access; for the initial-license cohort the fence must be at least 42 inches with a locked gate. An aboveground pool may have a 42-inch fence around its top with barricaded steps. These requirements operate alongside the city’s separate pool rules. Animals threatening children’s health or safety must be absent or securely penned away from children, with pens kept clean.
• Family burial grounds: Knowingly injuring or removing the fence around a protected abandoned family or private burial ground is a class A misdemeanor. The protected category is a site not deeded to the public with no interment for at least 25 years. A landlocked site without public ingress or egress carries reasonable-hours visitation access for ordinary cemetery purposes, enforced by the county sheriff or chief law-enforcement officer.
• State-park boundary projects: For a true common boundary with a state park or historic site needing livestock or commercial-game exclusion, written request and director approval precede state participation. Inspection considers need, resources, materials, cost and location; a required boundary survey is shared equally and a written decision is due within 60 days. The division supplies materials, while the owner constructs and maintains the fence. It must follow the verified boundary unless a written variance allows otherwise, without resource damage or grade changes draining wetlands or impounding water on park land.
• State-park boundary maintenance: Within that boundary program, brush, vine and regrowth maintenance may extend no more than 3 feet onto the park side. Vehicles, equipment and herbicides affecting park vegetation need facility-manager permission. Overhanging branches may be trimmed at the boundary up to 8 feet above ground. Removal requires written division consent except for temporary repairs. Participation is unavailable for poisonous crops, the specified saltpeter works or cotton gins, or costs another law or judgment already imposes on the owner.
• Captive-animal scope: The following captive-animal provisions apply only to a use otherwise lawful on the property. Section 210.090 prohibits dangerous nondog animals and specified wild animals in residential areas; a state permit or compliant enclosure does not override those city restrictions.
• Captive-cervid enclosures: For lawful, permitted captive-cervid holding, fence and posts must be at least 8 feet high throughout. Materials may be woven or high-tensile woven wire not smaller than 12.5 gauge, welded wire not smaller than 6 gauge, chain-link not smaller than 9 gauge, or wood planks. Vertical wire or plank spacing is at most 6½ inches. Stacked fences must overlap at least 6 inches and attach at intervals no greater than 3 feet, or combine and attach at intervals no greater than 12 inches. Ground clearance is at most 3 inches. These are captive-animal standards, not the rule for a garden fence intended to exclude wild deer.
• Captive-cervid perimeter: On land controlled by the permit holder, woody vegetation under 6 inches in diameter at breast height must be cleared at least 6 feet inside and outside the cervid fence. Enclosures or additions built after June 30, 2019 separately require all woody vegetation cleared for 6 feet on both sides. Dead trees taller than their distance to the fence must be felled. Gates must be locked and latched and meet the fence standard. Stream crossings, terrain and maintenance must prevent ingress and egress, with supplemental measures where needed.
• Large carnivores: Defined nonnative large cats and bears are subject to a separate Missouri Department of Agriculture permit for each animal and applicable U.S. Department of Agriculture standards. Circus, specified veterinary-school and qualifying zoological-park exclusions are separate. A yard-fence permit does not authorize possession or establish compliance with animal-enclosure requirements, and the animal use must also be lawful locally.
PRIVATE RESTRICTIONS
• Recorded and agreed restrictions: City zoning does not abrogate private easements, covenants or agreements. More restrictive zoning or higher public standards still govern. Recorded plats, homeowners-association conditions and private agreements about boundaries, access, maintenance or cost remain separate from government approval. A permit does not extinguish private rights or decide who owns a disputed strip of land.
REVIEW AND ENFORCEMENT CONTEXT
Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:
• Applications and existing fences: Permit and engineering decisions, yard classification, lawful nonconforming status and repair or replacement work.
• Historic and site conditions: Historic compatibility, utility access, right-of-way use, stream buffers, flood effects and visibility.
• Safety and maintenance: Pool barriers, sound fences and retaining walls, permitted animal enclosures and applicable household special uses.
• Private disputes: Boundary, easement, covenant and shared-cost issues follow the applicable private rights and legal procedures, separately from city approval.
USING THIS INFORMATION
This page provides general orientation on how residential fence rules are structured and applied within the incorporated City of Excelsior Springs, Missouri. Updated November 2026.
In addition to local fence rules, certain Missouri laws apply statewide. See Statewide Fence Laws in Missouri.
It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with the identified municipality, including its actual municipal or county class, charter, adopted program or special district, and each function’s verified territory, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Missouri law. Applicable requirements depend on the property’s actual facts and the respective authority of the identified offices. Private agreements and recorded rights remain separate from government approvals. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern.