FENCE RULES – ST. LOUIS (COUNTY), MISSOURI
OVERVIEW
This page covers residential fences and residential acreage in unincorporated St. Louis County, Missouri. Incorporated municipalities have their own zoning and adoption arrangements, even where County staff provide a contracted service.
St. Louis County separates building-permit exemptions from zoning placement rules. A new or replacement rear- or side-yard fence up to seven feet generally qualifies for the building-permit exemption, while the ordinary zoning exception allows boundary fences up to six feet within required structure setbacks. Pool enclosures and electrically charged or barbed fencing have separate treatment. Taller-fence rules depend in part on whether a single-family home occupies a platted lot. Corners, retaining walls, approved development plans, historic designation, drainage and floodplain conditions can change the project. Wood and vinyl are recognized decorative materials; chain-link has different screening and pool-barrier classifications. Rural homes also face applicable pasture, wastewater and excavation duties. Updated November 2026.
| Quick question | St. Louis County answer |
|---|---|
| Permit or approval | New or replacement fences no more than 7 feet high in rear or side yards are exempt from a building permit, except pool, spa and hot-tub enclosures and electrically charged, barbed-wire, razor-ribbon or similar fences. Separate zoning and site approvals still apply. |
| Typical fence height | Boundary fences 6 feet or less may occupy required structure setbacks in the districts described below. The 7-foot permit threshold is separate. A 10-foot cap applies under the landscaping section, which excludes single-family residential units on platted lots. |
| Placement & property lines | Property boundaries, roadway rights-of-way and easements are separate limits. Corner visibility, taller-fence setbacks, approved site conditions and pool-barrier clearances can restrict placement. |
| Common fence materials | Wood: recognized for decorative fencing. Vinyl/PVC: vinyl is recognized; PVC is not separately named. Chain-link: recognized in screening and pool provisions, but excluded from decorative and fully sight-proof classifications. |
| Important local conditions | Fence rules may be further affected by platted-lot status, zoning district, corners, pools, retaining walls, approved development plans, historic designation, roads and easements, drainage and floodplains, land disturbance, animal enclosures and wastewater systems. |
| Official local resource | St. Louis County ordinances and adopted-code amendments |
The table summarizes ordinary rules. The sections below explain their applicability, exceptions and the additional requirements for particular properties and fence designs.
GOVERNANCE
St. Louis County is a charter county. County zoning applies outside incorporated cities, towns and villages. The Department of Planning and Zoning Administrator administer zoning; Transportation and Public Works administers construction permits and the adopted construction codes. Municipal service contracts require corresponding municipal legislation and substantially identical construction-code provisions. A County service arrangement does not extend County zoning into a municipality.
The County adopts the 2015 International Residential Code, with Appendix K and local amendments, for qualifying detached one- and two-family dwellings, townhouses and accessory structures no more than three stories high. Its framework also includes the locally amended 2015 International Building Code, Appendices C and H, 2015 International Swimming Pool and Spa Code, and 2015 International Property Maintenance Code. References to these codes mean their County-adopted versions. The residential permit provisions are replaced by the County’s amended building-code permit provisions.
Floodplain, land-disturbance, road and sewage programs have their own coverage and approvals. County traffic rules also reach specified arterial roads within municipalities. Public Health and the County plumbing program have separate responsibilities for wastewater systems. Private title, easements and shared-fence obligations remain separate from these public functions.
PERMIT AND APPROVAL REQUIREMENTS
• New and replacement fences: A new or replacement fence no more than 7 feet high in a rear or side yard qualifies for the building-permit exemption if it does not enclose a pool, spa or hot tub. Electrically charged, barbed-wire, razor-ribbon and similar fences are outside this exemption at any height. Exempt work must still satisfy zoning, material, pool and other applicable requirements.
• Ordinary repairs: The repair exemption excludes repairs resulting from a disaster or lack of ongoing routine maintenance. Ordinary repair does not include cutting structural or load-bearing supports, changing required exits or egress, or the covered utility-system and other work affecting public health or general safety. A replacement is evaluated under the replacement-fence rule above.
• Retaining walls with fences: The retaining-wall exemption generally ends above 3 feet, measured from finished grade on the non-retained side to the top. A wall supporting a surcharge or impounding Class I, II or III-A liquids is limited to 2 feet for this exemption. A permit is required if the distance to the property line is no greater than the wall’s height, or if the wall plus guard or fence exceeds 6 feet from proposed finished grade on the non-retained side to the top.
• Plans and permit duration: Required construction documents generally consist of four sets, or approved electronic media, identifying the work, dimensions, location and code compliance. Exceptions from professional preparation include qualifying miscellaneous residential accessory structures and minor work approved by the official. Where private sewage is used, the site plan identifies the system. Work follows approved documents and applicable change review. Applications generally lapse after 180 days without good-faith pursuit or permit issuance; permits become invalid if work does not begin within 180 days or is suspended or abandoned for 180 days. Written, justified extensions follow the respective application and permit provisions.
• Permit fees: The codified residential miscellaneous-construction schedule uses project value, a $47 processing fee and applicable minimums. Construction values up to $1,000, $2,000, $3,000, $4,000 and $5,000 have base fees of $54, $63, $74, $87 and $105 respectively. The next $1,000 brackets through $10,000 have base fees of $118, $124, $141, $146 and $149. Processing is added. Minimum totals including processing are $94 for one inspection without plan review, $124 with plan review, $141 for two or more inspections without plan review, and $171 with plan review. Additional inspections cost $47, with $24 per additional half-hour or fraction beyond one hour including travel. Fees are generally paid in advance; valuation may use County unit rates or a bona fide contract or affidavit. The County may revise its schedule annually, so Transportation and Public Works determines the assessed fee for a required permit.
• Pools: The small-prefabricated-pool building-permit exemption requires all of these conditions: accessory to a qualifying dwelling, townhouse or Group R-3 occupancy; no more than 24 inches of water depth; no more than 5,000 gallons; and installation entirely above ground. Applicable barriers remain a separate requirement. A fence serving as a pool, spa or hot-tub enclosure does not qualify for the ordinary rear- or side-yard fence exemption.
• Site and historic approvals: Detached single-family dwellings and their associated accessory structures are exempt from general Site Development Plan review, but existing approved plans bind later owners and tenants and required landscaping and improvements must remain. Planned developments, conditional-use approvals and form-based overlays may carry property-specific conditions. In a Landmark and Preservation Area, the designation ordinance and Historic Building Commission review can govern height, setbacks, historic character, repairs, scale, color and materials. Demolition or moving a structure there requires the applicable permit and Commission approval, subject to the public-safety exception.
• Existing nonconforming fences: A lawful nonconformity may continue only under the applicable conditions; its owner bears the burden of establishing that status. For a nonconforming structure destroyed outside the owner’s control by less than 60 percent of replacement value, restoration without increased nonconformity must begin within six months and finish within two years. Destruction above 60 percent, or owner-controlled destruction, requires conformity subject to Board relief. An older fence’s presence does not by itself authorize rebuilding it in the same nonconforming form.
• Floodplain development: In mapped unincorporated A, AE, AO and AH flood-hazard areas, construction or other development requires a floodplain development permit. Development includes excavation, grading and other man-made changes. This approval is separate from a building-permit exemption.
• Land disturbance: County land-disturbance permits distinguish work below one acre from work disturbing at least one acre, including smaller work within a proposed development ultimately disturbing at least one acre. The acre/common-plan threshold also requires the applicable state permit. Conditional County exceptions cover residential additions and accessory structures, and property improvements moving less than 30 cubic yards while disturbing less than 2,000 square feet. They do not permit property-line cut or fill, permanent diversion between drainage areas, adjoining erosion or damage, blocked swales, unapproved floodplain work or channel work. Existing permitted or accessory agriculture, limited reseeding and home gardens have separate conditional exceptions; agricultural zoning alone does not exempt new pasture clearing.
FENCE PLACEMENT RULES
• Boundaries and setbacks: Boundary walls and fences 6 feet or less may stand within minimum structure setbacks in PS, NU, KP, R1, R1A, R2, R3, R4, R5, R6A, R6AA, R6, R7 and R8 districts, subject to the corner rules below. Setbacks run from the applicable lot line or roadway right-of-way, not simply the pavement edge. A recorded easement can restrict a fence even where zoning allows it near a boundary.
• Roads and access: Fences must respect road rights-of-way and recorded access rights. County rules prohibit structures or obstructions leaving less than 10 feet of available traffic width on a roadway or alley without a striped double-yellow centerline, or less than 10 feet in either direction of travel where that centerline exists. This traffic-clearance rule does not authorize occupying public right-of-way. Other County provisions regulate roadway hazards, materials and personal property; utility special-use permits and formal right-of-way vacation are separate processes.
• Drainage and floodways: Keep the applicable swales, channels and recorded drainage rights functional. In a regulatory floodway, encroachment requires hydrologic and hydraulic analysis demonstrating no increase in base-flood levels. Where no floodway is designated in the specified A or AE area, the cumulative increase limit is one foot. Approved site and floodplain conditions can therefore determine whether a fence is acceptable in a drainage path.
• Streams and protected trees: For land development requiring Planning-approved site plans and subject to Section 1003.162, stream buffers are 50 feet from the top of bank along waterways with a 100-year floodplain and 25 feet along other waterways, plus a separate 25-foot building setback. Agriculture, farming and regional trails have the stated exception, and single-family residential units on platted lots are excluded from that section. Where an approved development requires tree preservation, protective fencing is at least four feet high, using plastic mesh, chain-link or similar material, before grading. The protected radius is one foot per inch of trunk diameter at breast height, with a five-foot minimum and ten-foot maximum. These development conditions do not create the same setback or temporary-fence requirement for every home.
• Shared-fence removal: Ownership and statutory fence duties can affect removal even when the replacement meets County rules. Under Missouri’s general division-fence law, removal requires all owners’ consent except to open a public road or highway. Local-option adoption suspends those general provisions in a county where that system applies. Separately, voluntarily throwing down, opening or removing a partition fence adjoining cultivated fields carries a six-month written-notice requirement under Section 537.350. Notice does not substitute for required consent. Section 537.360 limits the covered recovery to single damages plus costs when probable cause supports the belief that the affected land or property was the defendant’s own.
• Utility notice before digging: Covered post-hole digging and other excavation require notice through Missouri One Call and facility-location information before work. Notice is given at least two and no more than ten working days before the expected start; working days exclude Saturdays, Sundays and legally declared state or federal holidays. The two-day clock begins at midnight following receipt. A ticket expires at 11:59 p.m. twenty-one consecutive calendar days from the work start date. The agricultural-tilling exemption is limited to sixteen inches; a marking-stake exception does not exempt structural fence posts. Utility marks do not establish property boundaries or permission to use land.
• Marks and unanswered notices: Marks must remain visible. Work not begun within ten working days requires relocation before starting; unusable marks require a remarking request with the original notice timing. Reasonable care and appropriate horizontal and vertical confirmation remain necessary, using hand or soft digging when possible. Incorrect or unmarked facilities are reported to the center, with a two-hour owner response to contact or correctly locate. After no response to a compliant original notice, a second center notice is required before work. The owner then has two hours to mark or contact the excavator with a marking time: a notice by 2 p.m. requires marking that working day, and a later notice by 10 a.m. the next working day. Failure to mark or contact permits commencement under that provision, while careful and prudent excavation duties continue.
• Excavation damage and emergencies: Excavation-related damage, dislocation or disturbance of a facility is reported to the notification center, including damage to trace wires, encasements, cathodic protection and permanent above-ground stakes. A hazardous-liquid or gas release from pipeline contact or damage requires an immediate 911 call. Damage cannot be concealed or repaired without facility-owner authorization. After notice, temporary emergency sewer repairs may prevent further damage without prior authorization. Genuine emergency excavation may proceed with reasonable precautions and notice as soon as practical; the facility owner has the statutory two-hour marking or contact duty. State-highway or right-of-way excavation also requires the transportation commission permit, subject to the railroad-right-of-way exception.
• Temporary excavation protection: Where needed to protect the public, a fence, railing, barrier or watchman guards dangerous excavation until the work or danger ends. The specified obstructions require lights at night.
FENCE HEIGHT AND VISIBILITY RULES
• Ordinary yards: The 6-foot boundary-fence rule in the listed districts allows fences within minimum structure setbacks. The building-permit exemption reaches 7 feet in qualifying rear and side yards. These provisions answer different questions: a fence can be exempt from a building permit yet still require a different location under zoning.
• Taller fences and platted homes: Where the landscaping and screening section applies, fences may not exceed 10 feet, and those over 6 feet must meet the underlying district setbacks. Single-family residential units on platted lots are excluded from that entire section. For those homes, the ten-foot provision does not supply a general maximum; the district, other applicable code requirements and approved property conditions determine the taller-fence design. Planned or conditional-use approvals may impose additional requirements.
• Corner visibility: The zoning sight triangle is bounded by the intersecting property lines and a line joining points 30 feet from their intersection, measured along those property lines. In the listed districts, structures and plants within that triangle may not exceed 3 feet above street pavement. The adopted building code’s separate fence provision prohibits fences within its corner site-distance triangle where that provision governs. Before placing a corner fence in the triangle, Transportation and Public Works must resolve the construction-code application to the property alongside the zoning rule.
• Guards at drops: For residential open-sided walking surfaces, the guard trigger is a drop more than 30 inches, measured vertically at the walking-surface edge to the floor or grade below. The local exceptions include retaining walls no more than four feet high, and taller retaining walls where the walk, path, parking area or driveway is at least two feet from the wall’s front face. A required guard serves a different purpose from a boundary fence.
• Residential pool barriers: The locally amended pool code generally requires a 72-inch barrier, with a 48-inch exception for residential swimming pools. Height is measured from grade on the side away from the pool or spa and must be maintained around the entire perimeter and for three feet horizontally outside it. The residential-swimming-pool exception is not stated as an exception for every residential spa. Bottom clearance, measured on the side away from the pool or spa, is at most two inches above grass, gravel or other nonsolid surfaces and four inches above solid surfaces. A barrier mounted on a pool or spa may have no more than four inches between the pool or spa top and the barrier bottom.
• Pool-side space and aboveground walls: The water-side barrier distance is generally 60 inches, reduced to 20 inches from the water edge for residential swimming pools. An onground residential pool wall can serve as its barrier only with the bottom on grade, top at least 48 inches above grade around the whole perimeter, compliance with the barrier requirements and manufacturer authorization. A barrier mounted on that wall must also reach at least 48 inches above grade around the whole perimeter and follow manufacturer instructions. Access ladders and steps must be surrounded by the required barrier.
• Livestock fences: Private horse pastures in the applicable NU, KP, R1, R1A and R2 district provisions must be fenced. Stable buildings have a 100-foot property-line setback, with an additional 100-foot sinkhole-edge setback in KP; those are stable-building distances, not pasture-fence offsets. Under the general Missouri fence-law system, a lawful livestock fence uses firmly set posts with wire or boards at least four feet high, mutually agreed by adjoining owners or determined by the associate circuit court. Posts are no more than twelve feet apart, with securely fastened members spaced to resist horses, cattle and similar livestock. System-specific duties remain separate from County zoning and dangerous-material restrictions.
MATERIAL AND CONSTRUCTION LIMITS
• Wood, vinyl, metal and masonry: The County’s decorative-fence definition recognizes wood, metal, vinyl, masonry and combinations. PVC is not separately named. Decorative fences may be open; chain-link, wire and wire mesh are excluded from that classification. A material’s recognition still leaves the applicable location, height and site conditions in place.
• Screening and chain-link: Where semi-sight-proof screening is required, it provides at least 70 percent but less than 100 percent screening; slatted or lattice-equipped chain-link can qualify. Fully sight-proof screening is 100 percent, and chain-link with slats or lattice does not qualify. Pool barriers have their own chain-link opening limits below.
• Electric, barbed and razor-like fencing: The adopted building code’s fence provision prohibits electrically charged fencing and new barbed-wire, razor-ribbon or similar installations where that provision governs. Its livestock-containing agricultural barbed-wire exception does not create unrestricted residential permission. Separate industrial, correctional and qualifying zoo exceptions do not authorize an ordinary home installation. Section 1003.162 also prohibits barbed wire in PS, NU, KP and residential districts within that section’s scope, which excludes single-family residential units on platted lots. Before choosing any of these materials, Transportation and Public Works must resolve the property-specific construction-code application and applicable zoning restrictions.
• Driveway barriers: Where the building-code fence provision applies, a driveway or parking barrier with less than three inches of vertical depth is considered hazardous. Its alternatives include permanent reflectors one inch horizontally by twelve inches vertically beneath the barrier at no more than 36-inch centers along its full length, or a No Trespassing sign in the middle of the entrance outside the right-of-way. Transportation and Public Works requirements also apply.
• Condition and protective finishes: Fences and walls must remain structurally sound and in good repair. Exterior wood other than decay-resistant wood needs paint, another protective covering or treatment. Peeling, flaking or chipped paint is removed and the surface repainted. Corrodible metal needs protection, with corrosion stabilized and coated; surfaces designed to stabilize by oxidation are excepted.
• Pool openings and climb resistance: Barrier openings may not pass a four-inch sphere. Solid barriers cannot form handholds or footholds through projections or indentations, apart from normal construction tolerances and tooled masonry joints. When the tops of horizontal members are less than 45 inches apart, those members belong on the pool side and vertical gaps and decorative cutouts are limited to 1¾ inches. With horizontal-member tops at least 45 inches apart, vertical gaps may reach four inches, while decorative cutouts remain limited to 1¾ inches. Chain-link openings are limited to 1¾ inches; reducing slats must be secured at top and bottom. Diagonal-member openings have the same 1¾-inch limit and a maximum 45-degree angle from vertical. Keep at least 36 inches between the exterior barrier and permanent structures or equipment that could aid climbing.
• Mesh pool barriers: Non-chain-link mesh follows manufacturer instructions. Its bottom is no more than one inch above the deck, installed surface or grade. It cannot be lifted more than four inches from grade or decking, allow a four-inch sphere beneath a panel, or leave more than four inches of bottom clearance from the solid surface, measured from grade or decking. Attachments are at least 45 inches above grade, patio sleeves are nonconductive and hinged gates meet the gate requirements. Mesh barriers cannot be mounted on an onground pool.
• Pool gates: Access gates accommodate a locking device. Pedestrian gates open away from the pool or spa and are self-closing and self-latching. Utility and service gates remain locked when unused. Double or multiple gates have one secured leaf and a self-latching adjacent leaf, with openings no larger than ½ inch within 18 inches of the release. A release below 54 inches above grade must be on the pool side at least three inches below the gate top, with the same ½-inch opening and 18-inch protection.
• House walls and safety covers: Where a dwelling or structure wall provides direct pool access, the specified options include UL 2017 alarms on doors and operable windows whose sills are less than 48 inches above the indoor finished floor; an ASTM F 1346 safety cover; or an approved equivalent such as self-closing, self-latching doors. Alarm controls are at least 54 inches above the finished floor in ordinary units and 48–54 inches in the specified accessible units. The construction-code barrier exceptions separately recognize lockable ASTM F 1346 covers for spas and hot tubs and powered ASTM F 1346 covers for pools. Existing-pool maintenance duties still apply independently.
• Natural edges: The natural-water-edge barrier exception requires that public shoreline access not be permitted and that barriers extend at least eighteen inches beyond the water edge. A natural-topography barrier requires governing-body approval and equivalent protection.
• Existing pools and spas: Private pools, spas and hot tubs with water more than 24 inches deep require a maintenance-code enclosure at least 48 inches above finished ground measured outside, with self-closing and self-latching gates or doors. A gate must positively close and latch when released six inches from its post. Existing enclosures cannot be changed or replaced to reduce effectiveness. The maintenance exception is for a spa or hot tub with the specified ASTM F 1346 cover. Pools must remain clean, sanitary and in good repair.
• Animals and pasture containment: A dangerous animal needs a securely locked enclosure strong and high enough to prevent escape over, through or under it; an electric-shock system does not qualify. Warning notice, identification-chip, neutering and controlled-leash conditions also apply. A dog or cat on its responsible person’s property is not automatically at large, but an animal in heat must be in an inaccessible residence or leashed and supervised on the premises rather than simply fenced outside.
• Loose livestock: Missouri law prohibits permitting horses, mules, asses, cattle, swine, sheep or goats to run at large outside their enclosure. A person restraining loose stock gives a known owner written notice within three days stating feeding and keeping compensation and claimed damages. The owner owes reasonable taking-up, keeping and feeding costs and actual damages, with the public-road-accident exception where escape occurred without the owner’s fault or negligence. Unknown ownership, or nonpayment of the taking-up, feeding and keeping compensation after notice, invokes the stray-law process; unpaid damages alone is not that trigger.
• Managed natural landscapes: The County program covers nonvacant recorded-subdivision property and property within 100 feet of the subdivision boundary in unincorporated territory. Covered landscaping stays at least five feet from an adjacent owner’s boundary unless a sight-proof solid fence is provided, and cannot obstruct vehicular, bicycle or pedestrian sight distance.
• Home wastewater lagoons: County plumbing approval and sanitary requirements remain applicable to private wastewater systems. Where the state onsite-sewage pond rule applies, the lagoon must be fenced before dwelling occupancy with a fence at least four feet high. Welded, woven or chain-link material is no smaller than 14-gauge wire; cattle or hog panels may substitute with a tee line post. Pressure-treated wood or galvanized or painted steel posts are driven, tamped or set in concrete, no more than ten feet apart, with braced corners. The fence must remain sound without bottom gaps. A properly hinged four-foot-high gate of comparable material needs an effective latch. The rule recommends 18-inch line-post and 24-inch corner-post depths and a gate width of 36–48 inches.
• Lagoon placement and state-program scope: The lagoon fence must be no closer to the water edge at the three-foot-deep operating level than the center of the berm. The recommended maximum thirty-foot distance from that water edge is advisory. The state program’s conditional exclusion covers an owner’s single-family residence lot of at least three acres, or an owner’s residential lot of at least ten acres with no single-family-residence onsite system within 360 feet of any other onsite system and no more than one single-family residence per ten acres in the aggregate. Lots adjacent to lakes operated by the Corps of Engineers or a public utility are excepted. All system points must be more than ten feet from adjoining lines, without effluent trespass, contamination or a scientifically determined nuisance. This state-program exclusion does not remove County plumbing requirements.
PRIVATE RESTRICTIONS
Recorded subdivision indentures, deed restrictions, private easements, homeowners’ association architectural rules and agreements about a boundary or shared fence can impose additional obligations. Existing approved public development conditions and statutory neighbor-fence duties remain separate. A government permit does not determine ownership, establish a surveyed boundary, allocate a neighbor’s share of costs or cancel recorded access and drainage rights. The floodplain ordinance preserves easements, covenants and deed restrictions while its greater public restrictions govern within their scope.
REVIEW AND ENFORCEMENT CONTEXT
Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:
• Permits and zoning: Whether a fence qualifies for the rear- or side-yard exemption, fits its district and platted-lot rules, preserves corner visibility and complies with an approved site plan.
• Special construction and site conditions: Pool barriers, gates, retaining walls, hazardous materials, historic-area work, floodplain encroachments, drainage, protected trees and land disturbance.
• Condition and residential uses: Unsound or deteriorated fences, required animal containment, applicable pasture fencing and state-regulated lagoon barriers.
• Private disputes: Ownership, recorded rights and shared-fence disagreements are distinct from County zoning and construction enforcement. Public stop orders and violations do not resolve private civil claims.
USING THIS INFORMATION
This page provides general orientation on how residential fence rules are structured and applied within unincorporated St. Louis County, Missouri. Updated November 2026.
In addition to local fence rules, certain Missouri laws apply statewide. See Statewide Fence Laws in Missouri.
It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with the identified municipality, including its actual municipal or county class, charter, adopted program or special district, and each function’s verified territory, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Missouri law. Applicable requirements depend on the property’s actual facts and the respective authority of the identified offices. Private agreements and recorded rights remain separate from government approvals. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern.