FENCE RULES – JEFFERSON (COUNTY), MISSOURI

OVERVIEW

This page covers residential fences in unincorporated Jefferson County, Missouri, including homes with agricultural acreage. Incorporated cities administer their own applicable requirements. County-maintained roads, state highways and private roads also have different approval and access rules.

Jefferson County exempts ordinary fences no more than eight feet high from a building permit, while zoning limits many residential front-setback fences to four feet. Rural/Agricultural and Large Lot Residential districts allow a taller front fence only with the required open upper portion. Side and rear fences can generally follow the property line, subject to landscape areas, corner visibility and recorded rights. Pools, sewage lagoons, designated landmarks, floodplain work and substantial grading have their own requirements. The county does not separately classify wood, vinyl/PVC and chain-link for ordinary yard fencing, but special-purpose enclosures have detailed construction standards. Updated November 2026.

Quick questionJefferson County answer
Permit or approvalOrdinary fences not over 8 feet are exempt from a building permit. Taller fences require one. Pool, historic, floodplain, driveway and grading approvals apply separately when their conditions are met.
Typical fence height4 feet in the front-setback area of R-40, R-20, R-10 and R-7. RA-5/LR-2 front fences may reach 8 feet with the required open upper portion. Residential side/rear fences may reach 8 feet, subject to corner and landscape restrictions.
Placement & property linesResidential side/rear property-line placement is allowed under the conditions below. Front-setback areas, road visibility, required landscaping, easements and drainage remain important.
Common fence materialsWood: not separately classified for ordinary yard fences. Vinyl/PVC: not separately classified. Chain-link: not separately classified for ordinary yard fences; expressly addressed for pool and lagoon enclosures.
Important local conditionsFence rules may be further affected by corner and driveway visibility, pool barriers, sewage lagoons, floodplain and grading work, designated landmarks, landscape easements, animal containment and private restrictions.
Official local resourceJefferson County Code Enforcement

The table summarizes ordinary rules. The sections below explain their conditions, exceptions and requirements for particular properties and uses.

GOVERNANCE

Jefferson County is a charter county, with a County Council that enacts county ordinances and a County Executive. Its Unified Development Order, building program and onsite wastewater ordinance apply in unincorporated territory. Hillsboro is the county seat. A mailing address or location within the county does not establish that a property is outside an incorporated city.

The Jefferson County Code combines zoning with separately adopted construction requirements. The county adopts the 2015 International Building, Residential, Fire, Fuel Gas, Mechanical, Energy Conservation, Plumbing, and Swimming Pool and Spa Codes, with local amendments, and the 2014 National Electrical Code with the 2017 county electrical code. The zoning fence limits and the building-permit exemptions operate independently.

Code Enforcement administers building permits and the local onsite wastewater program. The Planning Division maintains the landmark register and applicable historic guidelines. The Director of County Services and Code Enforcement is the floodplain administrator. Public Works administers the county grading and county-maintained-road driveway programs. State highway and private-road rights remain separate from those county functions.

Code Enforcement is at 725 Maple Street, Hillsboro, telephone 636-797-5310. Its official page provides the county’s online permit and inspection portal. Building-code appeals, zoning appeals and historic review use the distinct procedures described below.

PERMIT AND APPROVAL REQUIREMENTS

• Ordinary fences: A fence not over 8 feet high is exempt from the county building-permit requirement under the local building and residential codes. A taller fence requires a building permit under the general construction provisions. Every fence must still satisfy zoning height, placement and any applicable special-purpose requirements.

• Repairs and replacement: Ordinary repairs are exempt under Residential Code Section R105.2.2. Work affecting structural supports, required exits, specified building systems, public health or general safety falls outside that ordinary-repair treatment. New and replacement fencing remains subject to the applicable height, location and enclosure rules.

• Required plans: A required building-permit application uses the Code Enforcement form. For a lot of 4.99 acres or less, when the proposed structure is within 100 feet of any property line, the site plan shows property lines, front/side/rear building lines, proposed structures, floodplain, floodway and stream buffers. Section 400.430 generally requires surveyor staking and a site plan signed and sealed by a licensed surveyor or engineer, but exempts attached decks and structures under 200 square feet from those sealing and staking requirements. The work’s classification determines which requirements apply.

• Construction documents and completion: Required construction documents must be to scale and sufficiently clear. The local residential-code wording recommends preparation by a registered design professional. An approved set is retained by the official, with the other set onsite or available at inspection. A building permit must be completed by passing final inspection within one year. For reasonable cause, the Code Official may allow an extension of no more than one additional year. A demolition permit has a separate completion period of 180 days or a shorter period set by the official.

• Building fees and appeals: Section 500.250 sets construction fees by the applicable project category and valuation rather than one flat ordinary-fence price. Starting covered work without its required permit adds 100 percent of the normal permit fee, except for earthwork, stakeouts and necessary planning procedures. Building-code interpretation appeals go to the Board of Appeals; administrative and licensing issues go to the Code Commission. The Code Official’s appeal form must identify an incorrect interpretation, an inapplicable provision or proposed construction that is equally good or better.

• Lawful nonconforming fences: A lawful pre-existing nonconformity may continue when the owner establishes that status and the county recognizes it. Minor repairs and routine maintenance are allowed. Major renovation costing more than 50 percent of structural value is not allowed under Section 400.4930. A nonconforming structure destroyed beyond 50 percent of its structural value must be rebuilt in conformity. Permitted reconstruction must begin within 180 days, unless the Director grants an extension for extenuating circumstances. The separate accident-related dwelling exception applies to the specified dwellings, not automatically to a freestanding fence.

• Zoning relief: Zoning appeals follow Board rules and must be filed within no more than three months. The appeal fee is $250; a written nonconformity determination is $100, and a deviation is $75 each. The Board hears alleged enforcement errors and the authorized variance categories. Relief requires a hardship peculiar to the property, not self-created, and must protect public welfare and zoning intent. Authority to vary specified building or accessory-use setbacks does not amount to a general power to waive every fence-height limit.

• Zoning appeal hearings: Newspaper notice is required 5–15 days before the hearing, with notice to adjoining and fronting owners. A continuation for the decision may not exceed 90 days after the hearing. A Circuit Court appeal must be filed within 30 days of the Board’s final decision.

• Pools and spas: The adopted pool code covers permanent and temporary pools and spas designed and manufactured for connection to a circulation system and intended for swimming, bathing or wading. Permits cover construction, alteration, repair, moving, demolition and regulated systems. The local building and residential codes exempt prefabricated pools less than 24 inches deep from their permit requirement. Barrier requirements and other approvals remain separate. Additions, alterations and repairs must comply as new work without automatically bringing every untouched existing system up to new-construction standards. Minor work may retain an approved existing arrangement only when it is not hazardous; work may not make a system unsafe, unsanitary or overloaded.

• Retaining-wall permits: A retaining wall no more than 6 feet high, measured from finished grade to the top excluding the cap, is exempt from a building permit unless it supports a surcharge. Engineering, walking-surface guards, drainage and site requirements can still apply, as described under construction limits.

• Designated landmarks: The county historic-preservation provisions include fences as structures. Local designation follows the county process and requires the stated owner consent. The designation ordinance identifies the protected features, work subject to review and applicable guidelines. For a designated landmark, a determination of appropriateness is required for covered permit work, changes to specified significant features or appearance, and earth disturbance adversely affecting archaeological resources, including some work that does not require a building permit. Applications include plans and specifications; the Historic Preservation Commission’s form for non-building-permit work is available through Planning.

• Historic review timing: The Historic Preservation Commission decides within 45 days after receipt and provides written notice within 7 days. Approval becomes void if construction does not begin within 6 months. Determinations run for 18 months and are renewable. A denial includes findings and recommended changes, with an appeal to Circuit Court within 30 days.

• Historic nominations and safety work: Interim controls can withhold building permits from the presentation of a landmark nomination until County Council disposition. The related referral procedure calls for a commission response within 14 days, with an extension of up to 30 additional days, after which the Director’s permit authority resumes. County Council may order a permit issued when necessary for public health, welfare or safety. Work declared necessary by the responsible county department to correct an unsafe or dangerous condition is limited to what is reasonably needed to correct that condition.

• Floodplain development: A separate floodplain-development permit is required before covered construction, improvement, excavation or fill in mapped A, AE, AO or AH flood-hazard areas under county jurisdiction. Chapter 405 uses the October 2, 2025 flood maps, as amended. Development includes structures, grading, fill, excavation, drilling, storage and other man-made changes to land. The application describes the work’s location, nature, dimensions and elevations, provides relevant flood information, and requires the stated professional-engineer or land-surveyor signature. A building-permit exemption does not remove this floodplain approval.

• Land disturbance: Section 505.010 describes the county program as covering disturbance of 5,000 square feet or more inside the urban-area boundary, including common plans, and more than 15 acres outside it. The boundary follows the latest East-West Gateway functional-classification map. Section 505.190 states its 5,000-square-foot permit threshold more broadly. Public Works determines how those provisions apply to a proposed outside-urban project. The permit application is in the current owner’s name and is reviewed with its stormwater pollution prevention plan.

• Smaller, agricultural and emergency disturbance: Disturbance under 5,000 square feet is exempt from the county land-disturbance permit when it is not part of a larger common plan or sale. Erosion, runoff and siltation protection still apply, and the exemption can be revoked if erosion controls are missing. Farming, plowing, tilling and crop harvesting have a separate exemption, subject to aquatic-life and water-quality limits. An owner who clears or disturbs land for an exempt purpose, or an entity the owner controls, may not develop that site for two years afterward. Work immediately necessary to protect life, property, public health, safety or natural resources also has a separate exception.

• Land-disturbance fees: The county schedule effective January 1, 2026 charges $300 for 5,000 square feet to under one acre; $1,000 plus $50 per acre for 1–3 acres; $2,000 plus $50 per acre for over 3–10 acres; $3,000 plus $25 for each acre over 10 for over 10–25 acres; and $3,750 plus $10 for each acre over 25 above 25 acres. The fee includes 6 inspection hours below one acre, 20 hours for 1–3 acres and 40 hours above 3 acres. These fees apply to the covered land disturbance, not automatically to fence installation.

• County-road entrances: New, widened, relocated, replaced or improved driveway entrances onto county-maintained roads in unincorporated territory require the separate Public Works driveway permit and sight-distance review. A gate project that changes the entrance is subject to that road approval even when the fence itself is building-permit exempt.

• Onsite wastewater: Chapter 705 requires approval before constructing an onsite sewage system in unincorporated Jefferson County, including a single-family lagoon. Existing owners remain responsible for maintenance and safeguards; additions, repairs and replacements undergo the ordinance’s applicable checks. A lagoon is a rural alternative where soil is unsuitable for absorption, serves only one single-family residence, and requires the applicable registered, licensed designer’s design and stamp.

• State acreage provisions and county sewage rules: Section 701.031 excludes from the specified state onsite program the owner of a single-family residence lot of at least 3 acres, or the owner of a residential lot of at least 10 acres with no single-family-residence onsite system within 360 feet of any other onsite system and no more than one single-family residence per 10 acres in the aggregate. Lots next to lakes operated by the Corps of Engineers or a public utility are excepted. Every point of the system must be more than 10 feet from any adjoining property line, with no effluent entering adjoining property, contaminating surface water or groundwater, or causing a nuisance determined by a readily available scientific method. The state exclusion covers construction, operation, major modification and major repair. Jefferson County’s separate Chapter 705 requirements still apply. Section 701.047 preserves stricter local standards. The state’s suspension of its $90 application fee, effective August 28, 2026, does not waive county fees.

FENCE PLACEMENT RULES

• Residential side and rear lines: Under Section 400.2860’s fence and masonry-wall rules, a residential side-yard fence or wall up to 8 feet may be on the side property line. A rear-yard fence or wall up to 8 feet may be on the rear line when it abuts another lot or a designated thoroughfare. A required landscape area needs county approval for rear fencing and approved-development-plan authorization for side fencing. Corner-lot height and visibility limits apply independently.

• Homes in commercial or industrial districts: A fence or wall may occupy a side or rear property line, but cannot be in the required front yard or closer to a public or private street than the building setback unless an approved development plan allows it. This rule applies when the home is lawfully in one of those districts.

• The front-setback area: The required front yard is the area inside the front building-setback line. It differs from the general front yard between the main building and the lot front. Section 400.1670 measures the setback from the street right-of-way/property line or access-easement edge, whichever is more restrictive. Those distances locate the area where the front-fence rules apply; ordinary residential side/rear fences have their own property-line permissions.

• Residential front-setback distances: For RA-5 and LR-2, the distances are 100 feet on major streets, 65 feet on county-maintained streets and 25 feet on other streets, with the alternative in each category of the distance established by existing homes on the same side of the street. For R-40, the corresponding distances are 70, 50 and 25 feet, with the same existing-home alternative. For R-20, R-10 and R-7, they are 50, 35 and 25 feet. Major streets include interstates, major/minor arterials and collectors, and proposed four-lane streets.

• Other districts and corner lots: Front-setback distances in major/county-maintained/other-street order are 35/35/25 feet in PR-1, 35/35/15 feet in PR-2, and 20/20/15 feet in PC. NC-1, CC-2, PB, NPI and PI use 20 feet; PM uses the approved zoning plan. A corner lot has two front and two side setbacks. The front setback may be reduced by 5 feet when garage access is from an alley.

• Roads and access: The visibility provisions do not authorize objects in a street right-of-way. A fence or gate must respect the applicable road right-of-way and existing access rights. County-maintained-road driveway approval, state highway authority and private easements are separate. The county-road obstruction procedure in Missouri Section 229.150 excludes charter counties; Jefferson’s own road standards govern the county-road matters described here.

• Floodways and drainage: A floodway encroachment requires the specified engineering demonstration that it will not increase flood levels. In applicable A/AE areas without a designated floodway, the separate cumulative-rise limit is one foot. Excluding fences, pool enclosures or landscaping from certain substantial-improvement cost calculations does not remove the floodplain-development permit. Fill, sediment and runoff may not damage neighboring property, streets, drainage systems or waterways. Required drainage controls and easements must remain effective. On a hazardous disturbed site, the Director may require protective walls, fences or guardrails.

• Lagoon location: County treatment-system setbacks are measured from the nearest point of the lagoon system. They include 100 feet to property lines, building foundations or basements, private wells, springs and suction lines; 300 feet to public wells; 50 feet to classified waters and swimming pools; 25 feet to cisterns, streams/open ditches and downslope drains; 10 feet to pressure lines and upslope drains; 20 feet to embankment cuts at least two feet high and other absorption systems; and 500 feet to surface sinkholes. The lagoon must also be at least 200 feet from the nearest existing adjoining residence. These are treatment-system separations; the enclosure’s water-edge setback is described under construction limits.

• Lagoon setback qualifications: An unplugged abandoned well or a well with less than 80 feet of casing requires at least 150 feet of separation. Tank or absorption components may not occupy a sinkhole drainage area. Installing a septic tank or aerobic treatment unit before the lagoon does not reduce the required lagoon setbacks.

• Survey markers: Missouri Section 60.355 prohibits knowing removal, movement, defacement or destruction of its protected survey corners, boundary markers, benchmarks and horizontal-control monuments, subject to the registered-surveyor exception. It provides a class B misdemeanor classification, restoration-cost liability and the affected owner’s stated surveying-cost and attorney-fee remedy. Utility markings identify facilities rather than ownership boundaries.

• Notice before post excavation: Covered excavation includes hand digging, augering, drilling and driving fence posts, including on private property. Notice through Missouri 811 is required at least 2 working days, but no more than 10 working days, before the expected start. The period begins at midnight after receipt, excluding Saturdays, Sundays and state or federal legal holidays. The notice supplies the required location, contact, expected-start and work information. The agricultural tillage exclusion is limited to work no deeper than 16 inches; the temporary marking-flag/stake exclusion does not exempt structural fence posts. Private service lines are not all covered by the notification system.

• Utility responses and second notice: Notified facility owners ordinarily respond within 2 working days, unless the excavator agrees to extend the scheduled start through the notification center’s procedures. Excavation cannot begin before the scheduled date unless the excavator confirms that all underground facilities have been located. An unanswered original notice requires the prescribed second notice before excavation. The owner then has two hours to mark or contact the excavator. A second notice received by 2 p.m. requires marking that working day; later notice requires marking by 10 a.m. the next working day. Excavation may proceed only under the statute’s failure-to-mark-or-contact conditions, with prudent care still required.

• Ticket duration and care around utilities: The notice expires at 11:59 p.m., 21 consecutive calendar days from the work start date. Failure to begin within 10 working days requires relocation before starting; unusable markings require a remark request through the original notice process. Markings must be reasonably preserved. The approximate-location strip is the facility width plus 2 feet on each side, with a wider designation to the operator’s best ability for specified unusual locating conditions. Excavators determine suitable practices to establish horizontal and vertical location and use hand or soft digging when possible.

• Unmarked facilities and damage: An incorrectly located or unmarked facility requires notice to the notification center, followed by the owner’s two-hour response by contact or correct locating. Damage, dislocation or disturbance to a facility or its protective items, including trace wires, encasements, cathodic protection and permanent protective stakes, must also be reported to the notification center. Pipeline contact or damage that releases hazardous liquid or gas requires an immediate 911 call. The excavator may not conceal the damage or repair the facility without the owner’s authorization. After notification, emergency temporary sewer repairs may be made without that authorization to prevent further damage, while the reporting duty remains.

• Excavation emergencies and highway land: A genuine emergency permits necessary excavation with all reasonable precautions and notice as soon as practical. Within two hours of the emergency notice, the operator must mark or contact the excavator with available information; if marking cannot be completed in that period, the operator states when it will occur. Excavation within a state highway or its right-of-way separately requires Highways and Transportation Commission permission under Section 319.025, subject to the statutory railroad-right-of-way exception.

• Division-fence ownership and repair: Missouri has a general partition-fence system and a county-adopted local-option system. The applicable system, ownership and use determine statutory responsibilities; an ordinary privacy fence does not automatically make the neighbor responsible for half its cost. Under the general system, an owner must keep the owner’s division-fence portion in good repair and may enter adjacent land for that purpose. Under the local-option system, each owner maintains the assigned portion, and an adjoining owner may repair a defaulting owner’s portion at that owner’s cost.

• Removing a division fence: Under Section 272.120’s general system, removal requires all fence owners’ consent, except to open a public road or highway. Section 272.320’s local-option rule also excepts removal to make repairs. The repair exception and access rules depend on the applicable system and do not grant a general right to build across another owner’s land.

• Cultivated fields, open gates and damage: Section 537.350 separately addresses voluntarily opening or throwing down another enclosure’s doors, bars, gates or fences and leaving them open or down. Its partition-fence provision requires six months’ written notice to the owner of adjoining cultivated fields before the specified throwing down, opening or removal. The statute provides $5 plus double actual damages and costs, subject to its exceptions. That notice does not replace Chapter 272’s separate all-owner consent requirement. Under Section 537.360, probable cause to believe the land or thing taken, injured or destroyed was the defendant’s own limits the covered recovery to single damages and costs.

• Log-floating watercourses: Section 537.350 excepts fences across a watercourse carrying enough water to move lumbering logs at least 10 inches in diameter, railroad crossties or piling from its double-damage rule. The persons driving or placing them for floating remain liable for actual damage to bordering landowners. The statute excludes a stream fence enclosing no farm or plantation, or one apparently erected merely to hinder passage or extort money.

• Private family burial sites: Section 214.131 protects the fences, railings, tombs and structures of an abandoned family or private burial site that has not been deeded to the public and has had no interment for at least 25 years. Knowing destruction, injury, defacement or removal is a class A misdemeanor. If such a site is completely surrounded by private land without public access, reasonable ingress and egress for usual cemetery visits during reasonable hours must remain available. The sheriff or chief county law-enforcement officer enforces that access; court authority over disinterment and removal is preserved.

FENCE HEIGHT AND VISIBILITY RULES

• Residential front fences: Within the front-yard setback, fences and masonry walls in R-40, R-20, R-10 and R-7 may not exceed 4 feet. In RA-5 Rural/Agricultural and LR-2 Large Lot Residential, a front fence may reach 8 feet if each square foot of the portion above four feet has a ratio of two-thirds open space to one-third closed space. The ratio applies to that upper portion; picket and split-rail designs must meet it.

• Side, rear and corner fences: Residential side and rear fences or masonry walls may reach 8 feet under the placement conditions above. On a corner lot, a side-yard fence or wall over 4 feet cannot be in front of the front setback line. The same provision allows a side-line fence or wall to match one allowed by or located under the front-yard subsection, including its RA-5/LR-2 branch. Required landscape areas and sight clearances remain separate limits.

• Grade changes and retaining walls: The fence section does not provide a separate fence-grade averaging method or a combined retaining-wall-and-fence measurement formula. Code Enforcement determines the height treatment of a proposed unusual grade or stacked-wall design. Building-roof height definitions do not supply that fence measurement.

• Intersection and driveway corners: Section 400.2600 requires clear sight at intersections and driveways. Its corner triangle has 35-foot legs along the intersecting pavement edges, rather than the property lines. Obstructions are prohibited in the band 3–10 feet above adjoining pavement, except essential approved directional, traffic or utility devices.

• Roundabouts, posts and decorative fences: At a roundabout, clear vision includes points 25 feet from the pavement-edge lines of the outside curves. Vegetation, poles and posts in a sight triangle must leave the 3–10-foot band above ground level clear, be no more than 15 inches in diameter, and be at least 35 feet from the intersecting pavement edge. Decorative fences must preserve visibility throughout the clearance area and remain at least 35 feet from the pavement-edge intersection corners, including rounded corners.

• Longer intersection sight lines: The longer sight-distance test is separate from the small corner triangle. Section 400.2600’s target is 4.25 feet above pavement, at a point 12 feet back and approximately 3 feet right of the adjacent left-lane line; the observation height is 3.5 feet. Its introductory standard separately describes the approaching-lane line 3 feet above pavement. A crest requires one foot of clearance below the direct sight line, or a design cross-section where field measurement is impractical. Public Works applies the prescribed geometry to the entrance and road.

• County-road driveway sight distance: For entrances regulated by Chapter 515, the driver’s eye is located 12 feet from the outside lane edge. The county driveway sight-distance tables require 115, 155, 200, 250, 305, 360 and 425 feet on level roads at design speeds of 20, 25, 30, 35, 40, 45 and 50 mph, respectively. Table 2 supplies the level-range values; Table 3 adjusts for grade.

• Downhill grade adjustments: Using that same 20/25/30/35/40/45/50 mph speed order, the required distances in feet are 126/173/227/287/354/427/507 at −9 percent; 120/165/215/271/333/400/474 at −6 percent; and 116/158/205/257/315/378/446 at −3 percent. The level-range row directs use of Table 2.

• Uphill grade adjustments: In the same speed order, the distances in feet are 109/147/200/237/289/344/405 at +3 percent; 107/143/184/229/278/331/388 at +6 percent; and 104/140/179/222/269/320/375 at +9 percent. These are driveway sight-distance standards for the covered county roads, rather than fence setbacks from every road.

• Pool-barrier height: The adopted pool code generally requires outdoor pools and spas, and indoor pools, to have a barrier at least 48 inches above grade on the side away from the water. That height must continue around the entire perimeter and for 3 feet horizontally outside the barrier. Bottom clearance is no more than 2 inches over nonsolid ground, such as grass or gravel, or 4 inches over a solid surface, measured on the outside. Where a barrier is mounted on top of a pool or spa, the gap between the pool top and barrier may not exceed 4 inches. The construction and permitted alternatives follow below.

• Agricultural division-fence standards: Where Missouri’s general statutory fence system applies to the animal field or enclosure, the lawful fence consists of agreed or court-determined wire or boards at least 4 feet high, firmly set posts no more than 12 feet apart, secure fastening and spacing sufficient to resist the relevant livestock. Under an adopted local-option system, the specification is at least four boards per four feet of height, gaps no greater than twice board width, substantial posts no more than 12 feet apart with one stay; or four barbed wires with posts no more than 15 feet apart with a stay, or 12 feet without one; or an equivalent fence. These conditional animal-fence standards do not replace the county’s residential zoning limits.

MATERIAL AND CONSTRUCTION LIMITS

• Wood: The ordinary yard-fence provisions do not separately classify wood as an approved or prohibited material. Wood is expressly included in certain required structural-screen options, subject to their opacity, height and landscape conditions.

• Vinyl/PVC: The ordinary yard-fence provisions do not separately classify vinyl or PVC. Opaque vinyl is expressly recognized for specified structural screens, including the high-impact screen option described below.

• Chain-link: The ordinary yard-fence provisions do not separately classify chain-link. The pool code expressly regulates its openings, and the county lagoon ordinance expressly recognizes it subject to the lagoon’s separate wire, post, rail and gate standards.

• Other materials and orientation: Section 400.2860 regulates masonry walls alongside fences. The ordinary residential-fence provisions state no general ban on barbed wire, razor wire or electric fencing, and no general finished-side-out requirement. Visibility, required screening, designated-landmark standards, animal containment and nuisance provisions continue to govern their respective situations. Discarded fencing is included in demolition debris addressed by the county’s public-nuisance provisions.

• Required landscape buffers: Single-parcel residential structures in RA-5, LR-2, R-40, R-20, R-10 and R-7 are exempt from Table 14-1’s development screening/buffering requirements. An existing approved buffer or landscape easement still restricts fence placement. For covered development, side/rear buffers are generally at least 20 feet, or as Planning Commission approves. A nonresidential-to-nonresidential buffer can reduce to 10 feet; an 8-foot opaque landscaped screen instead of 6 feet can support a reduction to 10 feet. Buffers are recorded easements and are reserved for the permitted screens, berms and specified approved utilities or access.

• Development screens affecting a residential boundary: A new single-family subdivision with average minimum lots at least 2.5 times smaller than the adjoining previously approved or built subdivision requires a low-impact perimeter buffer. Where structural screening is required, it must meet its height when installed; plantings must attain required opacity within two growing seasons. The options include 6-foot masonry walls or 6-foot opaque vinyl/wood fences, berms and plantings as allowed for the impact class. Natural screens include suitable evergreen shrubs and trees providing an opaque screen through all seasons. Structural screens require surrounding vegetation, berm slopes no steeper than 3:1, at least one tree per 30 feet or fraction unless a lower density is approved, new trees at least 3 inches in caliper, and the finished/decorative face toward adjoining property. Berms cannot occupy the drip line of existing trees that remain. A screen set back from the property line needs decorative vegetation between the fence or wall and that line.

• Screening classes: High-impact screening requires a 6-foot masonry wall or opaque vinyl fence, exterior low-impact planting and 100 percent opacity. Medium-impact screening targets 70 percent opacity and allows the prescribed landscaping or fencing. Low-impact screening remains open. The required development or landscape plan determines the applicable class.

• Pool cover exceptions: The pool-barrier requirements except a spa or hot tub with a lockable safety cover complying with ASTM F1346, and a swimming pool with a powered safety cover complying with ASTM F1346. An ordinary tarp or manual swimming-pool cover does not meet those named exceptions.

• Pool openings and solid walls: General barrier openings may not pass a 4-inch-diameter sphere. A solid barrier may not provide handholds or footholds other than normal construction tolerances and tooled masonry joints.

• Mesh pool barriers: Mesh fences must follow the manufacturer’s installation instructions. The bottom must be no more than 1 inch above the deck, installed surface or grade. The fence cannot lift more than 4 inches above grade or decking, the maximum vertical clearance between the bottom and a solid surface is 4 inches from grade or decking, and no four-inch sphere may pass under a panel. Each section must attach at least 45 inches above grade with security at least equivalent to a hook-and-eye latch incorporating a spring-actuated retaining lever. Hinged gates must meet the pool-gate rules. Deck sleeves or post receptacles must be nonconductive. Mesh fences cannot be installed on top of an onground residential pool.

• Horizontal and vertical pool-fence members: When the distance between horizontal-member tops is less than 45 inches, those members must be on the pool side and vertical-member gaps and decorative cutouts may be no wider than 1¾ inches. At a distance of 45 inches or more, vertical-member gaps may be no wider than 4 inches; decorative cutouts remain limited to 1¾ inches.

• Chain-link and diagonal pool barriers: Chain-link openings may be no larger than 1¾ inches. Slats fastened at both top and bottom may reduce larger openings to that limit. Diagonal-member openings also may be no larger than 1¾ inches, and the members may be no more than 45 degrees from vertical.

• Pool clearances: Keep at least 36 inches between the outside of the barrier and permanent structures or equipment that could assist climbing. The inside face of the barrier must be at least 20 inches from the water’s edge.

• Pool gates: Access gates must be equipped to accommodate a locking device. Pedestrian gates open away from the pool and must be self-closing and self-latching. Utility and service gates must remain locked when not in use. With double or multiple leaves, at least one leaf must be secured in place and the adjacent leaf must self-latch; pedestrian gates also retain the self-closing requirement. No opening larger than ½ inch is allowed within 18 inches of the latch-release mechanism in that multiple-gate arrangement.

• Low pool-gate latches: If a self-latching release is less than 54 inches above grade, it must be on the pool side at least 3 inches below the gate top. The gate and barrier may have no opening larger than ½ inch within 18 inches of the release.

• A building wall forming the pool barrier: Doors and operable windows providing direct access through the barrier wall require the specified protection. The alarm option covers doors and windows with sills less than 48 inches above the indoor finished floor, with audible warnings when the opening or its screen is opened, listed and labeled to UL 2017. Operable parts of alarm-deactivation switches must be at least 54 inches above the finished floor in units not required to be Accessible, Type A or Type B. In units required to be those types, the operable parts must be 48–54 inches above the finished floor. Alternatives are a listed/labeled ASTM F1346 safety cover or an approved means, such as self-closing/self-latching doors, providing equivalent protection.

• An onground pool wall forming the barrier: When the manufacturer permits the pool wall to serve as the barrier, its bottom must be on grade and its top at least 48 inches above grade around the entire perimeter, meeting the barrier design requirements. For a barrier mounted on top of the pool wall, the top of the barrier must be at least 48 inches above grade around the entire pool perimeter, and both the pool wall and mounted barrier must meet Section 305.2. Access ladders or steps must be capable of being secured, locked or removed to prevent access, unless surrounded by a compliant barrier. Any opening created by securing, locking or removal may not pass a 4-inch sphere. A top-mounted barrier must follow the pool manufacturer’s instructions.

• Natural pool boundaries: Where the pool area abuts a lake or other natural body of water, the shoreline alternative requires no permitted public access along the shore and barriers extending to and at least 18 inches beyond the water’s edge. Natural topography or other natural barriers need official approval as providing protection equivalent to the specified barrier standards.

• Retaining-wall engineering: Residential Code R404.4 requires accepted engineering design for a retaining wall not laterally supported at the top that retains more than 48 inches of unbalanced fill, or a wall over 24 inches that resists lateral loads in addition to soil. The design addresses overturning, sliding, excessive foundation pressure and uplift, with a 1.5 safety factor against sliding and overturning. Building-supporting foundation walls have their separate code requirements.

• Guards at walking surfaces: The county requires guards along open-sided walking surfaces, stairs, ramps and landings more than 30 inches vertically above the floor or grade, measured at the edge. Guards are ordinarily at least 36 inches above the adjacent walking surface or tread line. Open stair-side guards may be at least 34 inches; a guard also serving as a stair handrail is 34–38 inches. Openings generally must prevent passage of a 4-inch sphere, with a 6-inch limit at the triangular stair openings and 4⅜ inches at other open stair-side guards. Insect screening is not a guard. A retaining wall without an associated walking surface is a different condition.

• Designated historic features: Historic review favors repairing distinctive features when feasible. Necessary replacement should match design, color, texture and visual qualities, and materials where possible. New work must be compatible and avoid destroying historic character; conjectural features, destructive treatments and damage to archaeological resources are restricted. The property’s designation and guidelines govern height, scale, landscaping, details, materials and maintenance.

• County lagoon enclosures: Section 705.420’s lagoon standards require a fence at least 5 feet high, made of chain-link or welded material no smaller than 14-gauge wire, with galvanized and/or painted steel posts and a metal top rail. The opening specification reads “two horizontal by four vertical” without stating a unit. Code Enforcement determines that opening-size detail for the design.

• Lagoon posts and openings: Posts must be driven, tamped or set in concrete. Line posts must be at least 18 inches deep and no more than 10 feet apart. Corner posts must be at least 24 inches deep and properly braced. The fence must remain sound with no bottom gaps or openings.

• Lagoon water-edge setback and gates: The fence must be no closer to the water’s edge than the center of the berm at the 3-foot operating water level, with a maximum 30-foot setback from the water edge. The ordinance separately specifies a properly hinged 4-foot-high gate of comparable material, at least 48 inches wide, with an effective latch. The fence must be complete before occupancy, with KEEP OUT signs on four opposing sides.

• Detention and retention basins: A covered detention or retention facility needs a 10-foot common-ground maintenance strip. A basin with side slopes steeper than 3:1 and a depth of at least 4 feet requires an approved perimeter fence at least 4 feet high. Post-and-rail or tall privacy fencing that obstructs maintenance observation should not be used.

• Animal restraint: County physical restraint can consist of a fence, structure or barrier that confines the animal. Voice commands, shock and other electronic restraint do not qualify as physical restraint. A declared dangerous animal must be indoors or in a locked enclosure that prevents escape and entry by young children, with secure high sides, an attached secure top, an attached solid non-diggable floor, a key or combination lock, and weather protection. The enclosure must meet zoning/building requirements, with warning notices at every premises entrance and each side of the enclosure.

• Livestock at large: Section 270.010 prohibits an owner from permitting a horse, mule, ass, cattle, swine, sheep or goat to run at large outside the owner’s enclosure. Any person may restrain the animals; the sheriff or other police officer must do so promptly on seeing them or receiving notice. Within 3 days, the person taking them up must give a known owner written notice stating feed/keep compensation and claimed damage. The owner owes reasonable taking-up, keeping and feeding costs and actual damages to injured persons. In a public-road/highway accident, the owner has a defense by establishing that the animals were outside the enclosure through no fault or negligence of the owner.

• The livestock stray-law procedure: The statutory stray-law process applies when the owner is unknown, or when a notified owner fails to pay compensation for taking up, feeding and keeping the animals. An unpaid damage demand alone is not that second trigger. Failure or refusal by an officer to perform the section’s duties can support the stated official-bond action by a damaged person.

• Licensed family childcare outdoor areas: At a licensed family childcare home, the play area must be on or adjoining the premises, convenient and accessible without hazards. Fencing is required when needed to protect children from traffic, water or other hazards. The fence must be at least 42 inches high for homes initially licensed after the rule’s effective date, or for new fences installed at existing facilities. All covered fences must prevent children from crawling or falling through or becoming entrapped, whether or not the 42-inch height requirement applies.

• Licensed family childcare pools and animals: Swimming and wading pools must be fenced to prevent children’s access. For homes initially licensed after the rule’s effective date, the pool fence must be at least 42 inches with a locked gate. An aboveground pool may use a 42-inch fence around its top with barricaded steps to the deck. The county’s applicable pool-code requirements also apply. Animals that may threaten children’s health or safety must be absent or securely penned where children cannot enter. Pens must be clean, and child-use areas free of animal excrement.

• Livestock boundaries beside state parks or historic sites: The state’s fence-participation program addresses preventing livestock or commercial game from entering adjoining park or historic-site land. A written Fencing Request Form and director/designee approval are required before participation. Inspection considers need, resource effects, materials, cost and the boundary. A required boundary survey is shared equally. Written approval or denial is due within 60 days after receipt. On approval, the division supplies construction materials as its statutory share; the landowner builds, and the owner and successors maintain the fence.

• Work at an approved park boundary: Construction must protect trees, structures, soil, wetlands, habitats and geological/historic resources. Elevations cannot be changed to drain wetlands or impound water on department land. The fence follows the identified boundary unless a written variance is approved. Maintenance includes brush, vines, woody regrowth or resprouting of approved cut trees no more than 3 feet inside park land. Brushhogs, tractors, heavy equipment, all-terrain vehicles, motorcycles or other vehicles require the facility manager’s permission, as do herbicides on or drifting onto park vegetation. Overhanging branches may be trimmed at the boundary up to 8 feet above ground. Removal needs written division consent except temporary removal for repair.

• Limits on state-park participation: The division does not participate in fencing saltpeter works, cotton gins or land planted with poisonous crops, or pay costs where another law or judgment already requires the landowner to fence. Participation depends on the qualifying boundary and livestock/game purpose.

• Permitted captive cervids: An enclosure for cervids held under the state permit regime must have fencing at least 8 feet high along its entire length, using woven or high-tensile woven wire no smaller than 12½ gauge, welded wire no smaller than 6 gauge, chain-link no smaller than 9 gauge, or wood planks. Vertical-wire or plank gaps may not exceed 6½ inches. Stacked fences must either overlap at least 6 inches and attach at intervals no greater than 3 feet, or be combined and firmly attached at intervals no greater than 12 inches. Ground clearance may not exceed 3 inches. These are captive-animal standards, rather than a height requirement for a garden fence excluding wild deer.

• Captive-cervid clearing and maintenance: Clear woody vegetation under 6 inches diameter at breast height for at least 6 feet inside and 6 feet outside on controlled land. For enclosures or additions constructed after June 30, 2019, the rule separately requires all woody vegetation cleared at least six feet inside and outside. Dead trees on controlled land taller than their distance from the fence must be felled. Posts must reach at least 8 feet and maintain integrity. Gates must be locked and latched and meet or exceed fence standards. Water gaps, terrain and ongoing maintenance must prevent entry and escape, using stronger or higher posts, grading, extra fencing or other measures where necessary. These obligations do not grant access to another owner’s land.

• Covered large carnivores: Keeping an animal covered by Missouri’s Large Carnivore Act, including its defined nonnative captive large cats or bears, is subject to a separate per-animal permit regime and the referenced United States Department of Agriculture standards. County land-use, animal and building requirements remain separate from that state permission.

PRIVATE RESTRICTIONS

Recorded covenants, subdivision restrictions, homeowners-association design requirements, private easements and enforceable boundary, maintenance or cost agreements can add obligations beyond county approvals. Section 400.070 preserves private covenants and easements, which county zoning does not administer. Property-line fence permission does not determine ownership, establish the surveyed boundary, allocate shared costs or give permission to attach to another owner’s fence.

A deeded access easement protects its holder’s reasonable use, including relevant passage, equipment access, maintenance and drainage. A fence can substantially interfere even when passage is not completely blocked. In Stoesz v. Wright, disputed interference required further proceedings rather than a final ruling that every fence in an easement is unlawful. The actual deed and facts govern.

An association’s recorded declaration can impose placement conditions beyond county zoning. In Bellemeade Homeowners Association v. Taylor, the court enforced that declaration’s rear-corner fence restriction and anti-waiver clause despite earlier nonconforming fences. Other properties depend on their own recorded documents and applicable law.

REVIEW AND ENFORCEMENT CONTEXT

Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:

• Permits and site approvals: Building-permit thresholds, replacement or nonconforming work, designated-landmark review, floodplain development, land disturbance and changes to county-road entrances.

• Placement and visibility: Front-setback and corner restrictions, sight lines, rights-of-way, required landscape areas, drainage and treatment-system placement.

• Enclosures and construction: Pool gates and barriers, lagoon fencing, retaining-wall engineering and guards, dangerous-animal enclosures and conditional licensed-home or agricultural uses.

• Separate private matters: Boundary, covenant, easement, ownership and shared-cost disputes remain distinct from county permit and code enforcement.

USING THIS INFORMATION

This page provides general orientation on how residential fence rules are structured and applied within unincorporated Jefferson County, Missouri. Updated November 2026.

In addition to local fence rules, certain Missouri laws apply statewide. See Statewide Fence Laws in Missouri.

It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with the identified municipality, including its actual municipal or county class, charter, adopted program or special district, and each function’s verified territory, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Missouri law. Applicable requirements depend on the property’s actual facts and the respective authority of the identified offices. Private agreements and recorded rights remain separate from government approvals. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern.