FENCE RULES – ST. PETERS (CITY), MISSOURI

OVERVIEW

This page covers residential fences inside the incorporated City of St. Peters, Missouri, in St. Charles County. Ordinary city zoning follows municipal boundaries, not the full county or a postal address.

St. Peters generally does not require a fence permit for an ordinary single-family home, but location, materials and a six-foot height limit still apply. Multifamily and specified other districts have a permit requirement. Front building lines control placement, with distinct corner, through-lot and physical-security branches. Wood and vinyl are recognized; chain-link and masonry above four feet need specific approval. Slats inserted in chain-link and fabric attachments are prohibited. Corner visibility, utilities and drainage can reduce the usable fence area. Pools require their own barriers and access safeguards, including a stricter local aboveground-ladder rule. Old Town, Centre, planned developments and animal enclosures add property-specific requirements. Updated November 2026.

Quick questionSt. Peters answer
Permit or approvalOrdinary single-family fence erection, installation or alteration generally needs no fence permit. R-3(A)/R-3(B), multifamily planned developments, commercial and industrial districts have exceptions; pool and other site approvals remain separate.
Typical fence heightGenerally 6 feet, including fences, walls and hedges. Front-yard, visibility, material and special-district rules still apply.
Placement & property linesOrdinary fences stay behind the front building line and within property lines. Corner and through lots have separate clauses. Corner extension is measured from the platted building line, not a presumed curb offset.
Common fence materialsWood: allowed. Vinyl/PVC: vinyl slats/planks allowed. Chain-link: allowed up to 4 feet; above 4 feet requires specific approval. Chain-link inserts and fabric attachments are prohibited.
Important local conditionsFence rules may be further affected by corners, through lots, utilities, drainage, streams, pools, grading, floodplains, Old Town, Centre, planned developments and animal enclosures.
Official local resourceSt. Peters Planning, Zoning and Development

The table describes ordinary residential rules. The sections below explain the exceptions and additional requirements for the property and project.

GOVERNANCE

St. Peters is a fourth-class city in St. Charles County. Planning and the Administrative Officer administer land use; the Building Commissioner handles construction and pool codes; the City Engineer handles grading, drainage, rights-of-way and designated floodplain functions. The Health Manager administers animal and hen-enclosure rules, and the Public Works Manager administers private sewage. Planning is available at 636-477-6600, extension 1670.

The city adopts the 2021 International Residential, Building, Swimming Pool and Spa, and Property Maintenance Codes with local amendments. The city’s own zoning and amendments govern alongside those codes; county zoning for unincorporated land is separate.

PERMIT AND APPROVAL REQUIREMENTS

• Ordinary fence work: Section 405.360 generally allows fence erection, installation or alteration without a fence permit. The exception covers fences in R-3(A), R-3(B), multifamily planned-unit developments, commercial and industrial districts, which need a building permit before installation and have a fence-permit fee no greater than $50. An ordinary single-family replacement still must meet location, height, material and applicable site requirements.

• Building-code and retaining-wall exemptions: The local residential code expressly exempts fences not over 6 feet from its building-permit requirement. Its retaining-wall exemption is for a wall not over 4 feet from the lowest adjacent grade to the wall top, unless it supports a surcharge or impounds Class I, II or IIIA liquids. These exemptions do not waive zoning, pool, district or floodplain approvals.

• Building-permit fees when applicable: The city’s fee schedule uses the higher of the supplied construction cost and current International Code Council valuation. For a permit with plan examination and value below $5 million, the multiplier is 0.0083; without examination it is 0.0070. The ordinary minimum is $50, or $25 for a minor individual-resident permit needing only one inspection. Extra or supplemental inspections cost $50 each, and starting without a required permit adds $50. The separate district fence-fee cap above remains applicable to its stated permit.

• Related site-work fees: Grading fees are 2 percent of grading, erosion, sediment and revegetation costs. Right-of-way work has a $25 instance fee, $15 per bore/crossing, and $15 per 100 linear feet of excavation. These project fees are not charges for an otherwise exempt ordinary fence.

• Pool-code refunds and appeals: Under §523.050, a permit refund is 90 percent when no work and no review occurred, or for a “same-as” review, and 80 percent after review but before work. No refund applies when the permit is voided, work stopped or work performed. The original permittee must apply in writing within 180 days after payment; an erroneously collected fee is fully refundable. A pool-code appeal must be filed on the official form within 20 days after notice, based on incorrect interpretation, inapplicability or equally good or better construction.

• Land-use applications: A variance or Board of Adjustment appeal costs $100, including certified mailings. Related residential driveway/curb-cut site review costs $30, and a boundary-adjustment plat costs $50. Those are separate applications; the ordinary fence exemption does not authorize changing a recorded boundary or driveway.

• Pool permits and documents: The city pool guide requires a permit before construction for pools over 24 inches deep, or shallower than 24 inches with pumped filtration. For a pool exactly 24 inches deep, have the Building Commissioner determine the required approval: the residential-code exemption covers only prefabricated pools less than 24 inches. A site plan shows pool size, location, distances to lines, drainage and barriers. Section 523.050 requires digital construction documentation and Missouri-licensed architect/engineer signed and sealed design, with an official waiver when that review is unnecessary and professional design is not otherwise required. Paper conversion may be charged at actual cost up to $1 per page; originally hand-drawn sheets no larger than 11 by 17 inches are not charged.

• Pool inspections and work before completion: The ground-rough electrical inspection occurs before trench backfill, with final inspection on completion. Requests by 4 p.m. are usually scheduled for the next working day. The guide states permits become void after 180 days of inactivity. Before filling a pool without its complete barrier, remove all ladders and steps. If they cannot be removed, or the pool wall is less than 48 inches high, provide a complete temporary barrier; noncompliance may lead to a court summons. Permanent aboveground access must meet the stricter local rule below.

• Grading permits: A City Engineer permit is required before grading unless an exception applies. The small-improvement exception uses the wording less than 300 cubic yards and/or 20,000 square feet, with work incidental to property improvement and no alteration of adjoining drainage. Other relevant exceptions include a building or pool foundation under an issued building permit; utilities/public works; agriculture, nursery or gardening substantially following soil-conservation standards; and permitted right-of-way work and trenches. A residential-lot escrow is not required unless the Engineer requires it. The permit ordinarily lasts no more than 120 days, unless an approved phased/revegetated schedule applies.

• Grading plans and work limits: Grading applications use two plan copies with proposed contours at 2-foot intervals, soil, structures/walls, quantity, drainage, erosion controls, access/parking and schedule. Identify sewage systems and underground utilities within 50 feet, gas transmission within 100 feet, geologic features and floodplain/floodway. Cut and fill slopes ordinarily cannot exceed 3 horizontal to 1 vertical without stability certification by an experienced registered soils engineer. Hauling more than 300 cubic yards over city streets needs written notice at least 2 working days before use. Grading is limited to dawn to dusk, Monday through Saturday, except emergencies or a specific City Engineer/designee extension.

• Floodplain development: Chapter 410 applies to the designated flood-hazard land inside the city and city-owned property outside municipal limits. The City Engineer, designee or City Administrator’s appointee administers it. A separate permit is required for each structure or other development before work; plans identify location, work, use, value, floodway/fringe and base/proposed elevations. Floodway encroachment requires standard engineering analysis demonstrating no increase in base-flood levels. Applicable floodplain uses also follow §405.370. Where property is elevated above the base flood, obtain the required map revision or amendment before occupancy, or within 120 days after grading when no immediate building is planned; the Building Code Official may grant a 90-day extension.

FENCE PLACEMENT RULES

• Interior and through lots: On an interior lot that is not a through lot, a fence cannot extend beyond the front building line or side/rear property lines. A through lot may be fenced to and along the line opposite the structure’s front, but not beyond its front building line or any property line. No additional general numeric side/rear fence offset is stated. Establish the platted lines and boundary before laying out the fence.

• Corner lots: A corner fence cannot pass the platted front building line parallel to the house front. At another platted front building line, it may extend 10 feet beyond that platted building line, while staying outside the required sight area. Where corner lots’ rear property lines abut each other, the side-of-structure front-yard fence setback may be the property line. The ten-foot allowance is measured from the building line, not ten feet from the property line or a typical curb distance.

• Front-yard security and decorative sections: A front yard generally cannot be enclosed except under the through-lot branch or as a physical security measure. A security fence cannot completely block the view of the front yard, deny access to the public right-of-way, sidewalk or utility easement, or harm drainage. Decorative fence sections and trash enclosures are not treated as fences and may be in front yards. Ornamental driveway/sidewalk dividers and plastic chains/posts likewise are outside the fence definition.

• Utilities and public rights-of-way: Contact the City Engineer or developer to locate dedicated utility easements. The city is not responsible for replacing a fence removed from an easement. Never enclose or block a catch basin, culvert or stormwater structure. Fence materials and structures cannot project into a street or road right-of-way. Right-of-way excavations need Engineering approval. Utility-location notices for digging are separate from locating easement boundaries.

• Drainage and stream areas: Fences, sheds, landscaping and decorative blocks cannot block or alter adjoining drainage. Install runoff controls before land disturbance. For development along a natural watercourse, the setback is 25 feet from the top of the bank, or from the 15-year, 20-minute storm water elevation when no defined bank exists; preserve native vegetation and grades. A residential lot of at least 1 acre is exempt if the stream bank is not erosive. A restrictive crossing or enclosure carrying more than 10 cubic feet per second in that storm needs engineered plans and a permit. These stream-development conditions do not create a universal 25-foot boundary-fence setback.

• Pool equipment and decks: Pools, equipment and accessory decks cannot occupy an easement, be within 6 feet of a property line, intrude into the approved corner side-yard setback, or be placed under or near overhead power. Their placement is separate from the perimeter fence. Electrical clearances and bonding must be resolved as part of the pool’s electrical design and inspection, rather than using electrical dimensions as general fence setbacks.

• Boundaries and survey markers: A survey establishes the boundary; an old fence, hedge or mowing line does not establish it by itself. A surveyor’s real-property report is not a boundary survey for locating a new fence. Missouri §60.355 protects public-land corners, property markers, benchmarks and survey-control monuments from knowing movement, removal, defacement or destruction, except by a registered land surveyor. Violation is a class B misdemeanor. The statute provides restoration-survey costs and the affected owner’s stated attorney-fee remedy.

• Before digging fence-post holes: Missouri’s underground-facility law covers digging, augering and driving on private land as well as public property. Under §319.026, notice to the notification center is required at least 2 working days, but no more than 10 working days, before expected excavation. Missouri 811 is the notice service. The two-working-day period begins at midnight following receipt; Saturdays, Sundays and legal holidays do not count. The notice supplies the excavator and responsible-person contacts, location, expected start, depth, type of work and other required details. Utility marks do not establish a property boundary or permission to use another person’s land.

• Locate responses: Operators ordinarily respond within two working days unless the excavator agrees to extend the scheduled start. Work cannot start before the scheduled date unless all facilities have been confirmed located. If an operator has not responded to a proper original notice, §319.030 requires a second no-response notice before excavation. The operator then has 2 hours to mark or contact the excavator with when marking will occur. A notice received by 2 p.m. requires marking that working day; a later notice requires completion by 10 a.m. the next working day. Only failure of the statutory mark-or-contact requirement permits starting under that exception. Careful and prudent excavation remains required.

• Ticket life and usable markings: Under §319.025, the notice remains operational through 11:59 p.m., 21 consecutive calendar days from the work start date. If work does not begin within ten working days of the request, a relocation request is required before starting. Preserve visible marks; unusable marks require a remark request using the original notice period. The ordinary approximate-location strip is the facility width plus 2 feet on each side, with a wider designation for the specified unusual locating conditions. Determine appropriate practices for confirming horizontal and vertical location and use hand or soft digging where possible. An unmarked or incorrectly located facility must be reported through the notification center; the operator has two hours to contact the excavator or locate it correctly.

• Damage during excavation: Report facility damage, dislocation or disturbance, including damage to trace wires, protective encasements or stakes, to the notification center. Contact or damage causing a hazardous-liquid or gas release requires an immediate 911 call. Do not conceal damage or attempt repairs without the facility owner’s authorization. The narrow allowance for emergency temporary sewer repairs after reporting is to prevent further damage and does not cancel notification. For an excavation necessary because of a statutory emergency, all reasonable precautions to protect facilities remain required, and notice must be given as soon as practical. Within two hours, the operator must mark or contact the excavator with immediately available information and, if unable to mark within that period, state when it will mark. Excavation in a state highway or its right-of-way also requires the Missouri Highways and Transportation Commission permit under §319.025, subject to its railroad-right-of-way exception.

• Removing a division fence: Under Missouri’s general partition-fence system, §272.120 requires all owners’ consent before removal of a division fence, except to open a public road or highway. Section 537.350 separately requires six months’ written notice to the adjoining field owner for its partition-fence removal or opening branch where the adjoining fields are cultivated. It also addresses voluntarily opening or throwing down another enclosure’s doors, bars, gates or fences and leaving them open or down. The consent and written-notice duties are separate. Section 537.350 provides $5 plus double actual damages and costs. Section 537.360 limits covered recovery to single damages and costs when there was probable cause to believe the land or thing was the defendant’s own. Specialized watercourse/log-driving exceptions are separate from ordinary yard-fence removal.

FENCE HEIGHT AND VISIBILITY RULES

• Rural fields where livestock are kept: Where Missouri’s general partition-fence system applies, §§272.010–272.020 require a lawful fence for fields and enclosures where animals are kept. A lawful fence consists of posts and wire or boards at least 4 feet high, agreed upon by adjoining owners or determined by the associate circuit court. Posts must be firmly set no more than 12 feet apart, with wire or boards securely fastened and spaced to resist horses, cattle and similar livestock. County local-option rules and private agreements can affect shared-fence duties; these agricultural provisions do not raise a local residential fence-height limit.

• General six-foot limit: The city fence and residential site provisions generally limit fences, walls, shrubs and hedges to 6 feet, subject to the specific district exceptions. The fence definition includes living barriers within or along the lot; sight-proof forms include stockade, masonry, shadow-box and dense hedges. The ordinary fence provision does not specify a separate sloping-grade measurement method. For a sloped proposal, Planning can identify the applicable measurement for the submitted layout; pool-barrier grade measurements below are separately defined.

• Intersection visibility: Do not place an obstruction that substantially blocks the view of intersection traffic. At residential and minor-collector street corners, the sight area extends 30 feet from the intersection of the two adjacent property lines. Other street classes follow St. Louis County Department of Highways and Traffic Design Criteria §40.25. Before placing a fence on those other corners, give Planning a survey to have the applicable sight area marked, at 636-477-6600, extension 1670. The residential/minor-collector distance does not determine the clearance for every street class.

MATERIAL AND CONSTRUCTION LIMITS

• Livestock outside the enclosure: Missouri §270.010 prohibits an owner from permitting horses, mules, asses, cattle, swine, sheep or goats to run at large outside the owner’s enclosure. Anyone may restrain them, and law officers must. If the owner is known, written notice must be given within 3 days, stating feeding/keeping compensation and claimed damages. The owner owes reasonable taking-up, keeping and feeding compensation plus actual damage. For a public-road or highway accident, the statute preserves a defense where the owner establishes no fault or negligence. The stray-law route applies when the owner is unknown or a notified owner fails to pay taking-up, feeding and keeping compensation; unpaid damages alone do not trigger that route.

• Where residential material rules apply: The current residential requirements cover R districts and residential developments in Old Town S-D, St. Peters Centre and planned-unit developments. The height branches below govern material choices; an approved special-district plan can add requirements.

• Wood: Wood is allowed for residential fences both up to four feet and above four feet, subject to the general height and location limits.

• Vinyl/PVC: Vinyl slats or planks are allowed in both height branches. Vinyl-coated chain-link or metal is not classified as vinyl fencing. Slats inserted into chain-link are prohibited.

• Chain-link and masonry: Chain-link and masonry are allowed for fences 4 feet high or less. Above four feet, either requires Administrative Officer approval based on substantial evidence that other allowed materials are impractical and the design presents no aesthetic problem. Wrought-iron-appearance metal is allowed in both height branches.

• Prohibited residential materials: Slats inserted within chain-link and fabric attachments are prohibited. Residential barbed wire, hardware cloth and similar materials, and fences of one or more wire strands, are also prohibited. Pool-code performance specifications do not authorize a material prohibited by these residential rules.

• Finished side and repairs: The improved side must face outward where the fence is adjacent to a public street. Patched or extended work must match the original materials and design as one unit. Replace damaged boards, maintain staining/paint and remove rust. Remove a residential fence that is unsightly or a public hazard, and finish construction within 6 months after starting. The property-maintenance code also requires structurally sound fences and walls in good repair, without holes, breaks, loose or rotting material, mold or mildew.

• Agricultural and physical-security exceptions: A-1 agricultural property has an allowance for electrified or barbed-wire fencing as specified by applicable Missouri law. The city’s electric-fence prohibition also recognizes statutory exceptions, including qualifying nonresidential use within a residential district. Missouri §67.301’s battery-charged security-fence regime applies to property not designated for residential use; it is not general permission for a home’s electric perimeter fence. Section 67.494 retains local aesthetic, access, structural and drainage authority and requires emergency-responder entry. The front-yard security conditions above remain relevant.

• Old Town: The S-D Special Old Town Overlay preserves the Old Town area shown on the zoning map. Yard requirements fit existing layouts and need individual Planning and Zoning Commission approval. Late-nineteenth- and early-twentieth-century architecture is modeled where possible with Administrative Officer approval. Residential fence material and construction rules also apply there.

• Multifamily edges: In R-3(A)/R-3(B), property abutting R-1/R-2 must maintain a continuous back/side green belt at least 10 feet wide, with a 6-foot vinyl fence on the multifamily property line. Keep the landscaping healthy and do not use the buffer for parking or loading. This duty belongs to the specified multifamily boundary.

• St. Peters Centre and planned development: Centre site rules call for a 20-foot buffer with a sight-proof fence or berm along rear/side edges adjoining residential land, with 6-foot evergreen plants at 10-foot centers. The Centre provision also specifies noninstitutional vinyl or masonry fences no higher than six feet behind the front line, with side/rear-line placement allowed and easement-removal liability retained. Residential Centre developments additionally follow the current residential material rule above. Approved development agreements govern landscaping and site design for the permitted residential planned-development branches. Planning reviews the applicable agreement and overlapping material conditions for the particular property; other planned-unit developments likewise follow their approved plans.

• Running bamboo: Running bamboo must stay entirely on its planted property and not spread onto adjoining public or private land, rights-of-way, streets, sidewalks, alleys or easements. It cannot interfere with storm structures, utilities, retaining walls or foundations. A violation notice can require a written correction plan within 30 days, with measures completed within 90 days after approval unless the city allows longer for season or scope. The owner bears containment, removal and repair costs.

• Pool covers and construction fencing: Outdoor pools and spas and indoor swimming pools need compliant barriers under the adopted 2021 International Swimming Pool and Spa Code. A spa or hot tub with a qualifying lockable ASTM F1346 safety cover, or a pool with a qualifying powered ASTM F1346 safety cover, is exempt from §§305.2–305.7. In-ground pool and spa sites still require construction fencing at least 4 feet high, from excavation until the permanent barrier is complete.

• Pool barrier height and openings: A barrier under §305.2 must be at least 48 inches high, measured above grade on the side away from the pool around the entire perimeter and for 3 feet horizontally outside. The bottom gap is at most 2 inches over grass or gravel or 4 inches over a solid surface, measured on the side away from the pool or spa. If mounted on a pool wall, the gap between the wall top and barrier bottom is at most 4 inches. Openings cannot pass a 4-inch sphere. Solid barriers cannot provide handholds or footholds beyond normal construction tolerances and tooled masonry joints.

• Pool fence members and chain-link: When horizontal-member tops are less than 45 inches apart, horizontal members must face the pool, and vertical-member gaps and decorative cutouts are limited to 1¾ inches. When horizontal-member tops are at least 45 inches apart, vertical gaps may be 4 inches, but decorative cutouts remain limited to 1¾ inches. Chain-link openings cannot exceed 1¾ inches. The city prohibits slats inserted into chain-link, so that method cannot be used to achieve the required opening size. Diagonal-member openings are limited to 1¾ inches, and diagonal members cannot exceed 45 degrees from vertical.

• Removable mesh pool fencing: Mesh other than chain-link must follow manufacturer installation instructions. Its bottom must be no more than 1 inch above the deck, installed surface or grade. Clearance between the mesh bottom and solid surface must not allow the fence to lift more than 4 inches from grade or decking. No 4-inch sphere may pass beneath any panel, and the maximum bottom-to-solid-surface clearance is 4 inches from grade or decking. Each section’s attachment device must be at least 45 inches above grade; the code gives a hook-and-eye latch with a spring-actuated retaining lever as an example of attachment security. Hinged gates follow §305.3. Patio-deck post sleeves must be nonconductive. Mesh fencing cannot be mounted atop an onground residential pool, and its inside face must be at least 20 inches from the nearest pool or spa water edge. The proposed material must also meet local residential material restrictions and any necessary approval.

• Pool gates and doors: Access gates and doors must accommodate a lock. Pedestrian gates and doors open outward, away from the pool or spa, and self-close and self-latch. Nonpedestrian utility or service gates and doors remain locked when not in use. Double or multiple doors and gates need at least one secured leaf and a self-latching adjacent leaf.

• Residential pool latch heights: An outside-accessed latch release that is not self-locking must be at least 54 inches above the finished floor or ground surface. For a self-locking key, electronic or combination mechanism, both the lock control and latch release must be no higher than 54 inches above the finished floor or ground surface. At private pools, a self-latching gate with its sole release on the pool or spa side must place that release at least 3 inches below the gate top. Openings in the door, gate and barrier within 18 inches of an inside latch release cannot exceed ½ inch in any dimension.

• Equipment outside a pool barrier: Equipment on the same lot, including pumps, filters and heaters, must be at least 36 inches from the outside of the barrier when located outside that barrier.

• A building wall used as the pool barrier: Where a dwelling or structure wall provides direct access to the pool, §305.4 allows specified protective alternatives. The alarm option covers doors, gates and the specified windows with sills below 48 inches above the indoor finished floor, using a UL2017 audible water-hazard entrance alarm. The window provision covers operable windows. Alarm-deactivation controls must be at least 54 inches above the finished floor in dwellings not required to be Accessible, Type A or Type B units; in those accessible categories they must be 48–54 inches above the finished floor. Alternatives include a listed and labeled ASTM F1346 safety cover or approved equivalent protection, such as self-closing, self-latching doors.

• An onground pool wall used as the barrier: Under the local pool-code amendment, a wall used alone must rest on grade, have its top at least 48 inches above grade around the entire pool perimeter, comply with §305.2 and have manufacturer approval for barrier use. A wall with a top-mounted barrier must place the top of the barrier at least 48 inches above grade around the entire pool perimeter, with both wall and barrier complying with §305.2. Access ladders or steps must be capable of automatically being raised or secured, with the release 54 inches above the walking surface, or be enclosed by a barrier meeting §305.3. Any opening created by securing, locking or removing access cannot pass a 4-inch sphere. Top-mounted barriers follow manufacturer installation instructions.

• Natural pool-barrier alternatives: The natural-water-edge exception applies only where public access to the shoreline is not permitted and the required barrier extends at least 18 inches beyond the water edge. A natural-topography barrier needs governing-body approval and protection equivalent to §§305.2–305.5.

• Existing pools, spas and hot tubs: The property-maintenance code separately requires private pools, spas and hot tubs containing water more than 24 inches deep to have a barrier at least 48 inches above finished ground level, measured on the side away from the pool, and self-closing, self-latching gates. A release below 54 inches above the gate bottom must be on the pool side. Gates must positively close and latch when released 6 inches from the gatepost. Existing enclosures cannot be altered, removed or replaced to reduce effectiveness. This provision’s ASTM F1346 safety-cover exception is for spas and hot tubs.

• Erosion controls for site work: Sites with more than 20,000 square feet of grading need approved sediment-control plans maintained until adequate cover develops. Temporary revegetation is required within 14 calendar days after completion or suspension. Grading-permit disturbance of at least 1 acre needs a stormwater pollution prevention plan; disturbance under an acre needs perimeter siltation controls protecting adjacent property, rights-of-way, storm sewers and drainageways. Maintain temporary construction barriers against offsite mud until stabilization, clean daily and as needed, and maintain stabilized entrances. For separately permitted substantial grading, City Engineering specifies the silt-fence design under its erosion standards.

• Construction entrances: Where the local construction-entry controls apply, provide a stabilized entrance at each construction access. The clean aggregate is at least 1 inch in size and 6 inches thick, over filter fabric. Width is at least 14 feet and the full access width; length is generally 70 feet, reduced to at least 30 feet for a single-residence lot. Pipe runoff across the entrance or use a 5-to-1 mountable berm where piping is impractical. If gravel does not remove mud, wash tires while capturing sediment and preventing discharge to drains or waters. Install as soon as practical, maintain until permanent stabilization and remove tracked sediment immediately. These are site-work controls, not permanent yard-fence dimensions.

• Home beehives: A residential apiary requires a lot of at least 10,000 square feet and may have no more than 3 hives. Place hives behind a 6-foot sight-proof fence and out of view where possible. Provide fresh water within 5 feet. The apiary must be at least 20 feet from property or public right-of-way lines, with hive openings toward the most distant property line.

• Hens and agricultural animals: The agricultural-animal branch addresses farm/riding-stable horses, chickens including roosters, cattle and ducks. Stables/sheds must be at least 50 feet from the property line, and a horse/pony lot needs at least 3 acres. The separate residential-hen allowance is for a single-family residence on at least 1 acre, with a Health Manager permit, no more than 8 hens and no roosters. The applicant must live on the property.

• Residential hen enclosure: Use one rear-yard coop/pen with escape-proof fencing, predator protection, ventilation and sanitary conditions. Materials must be uniform, treated or painted, and in good repair. The coop provides at least 4 square feet per hen and is at most 14 feet high; the pen provides at least 10 square feet per hen and is no larger than 80 square feet. Keep both at least 10 feet from property lines, 25 feet from a neighboring residence and 10 feet from a swale or inlet. The residence distance does not apply to freestanding outbuildings. Buffer ground-level views from neighbors and the right-of-way using a sight-proof fence, landscaping or approved structure; standard residential sheds do not require buffering. Remove or till waste every 48 hours. No runoff, slaughter, egg sales, aggressive hens or running at large is allowed.

• Ordinary pets and electronic containment: An unaccompanied animal outdoors on its owner’s property needs a visible physical fence or substantial tether. An accompanying responsible adult must demonstrate command control, including preventing charging at passing people or vehicles. Electronic Invisible Fence containment is allowed only behind the front building line and must be maintained. The Health Manager may require a sign at least 6 by 8 inches but no larger than 4 square feet. Females in heat need secure enclosure. Lawful hunting and official-service exceptions are separate.

• A returned dangerous animal: A dangerous animal returned to its owner must be securely indoors; outdoors with an approved muzzle and durable nylon leash no longer than 4 feet under competent control; or in a locked enclosure preventing child entry and animal escape. The enclosure must be at least 5 by 10 feet, have strong sides and a secure top, and have a bottom secured to its sides or sides embedded at least 12 inches. Provide adequate shelter and weather protection. The Health Manager may waive construction requirements for demonstrated unique property difficulties.

• Related dangerous-animal conditions: That classification also requires an orange collar, microchip, immediate missing/attack notice, 24-hour death/transfer notice, neutering within 30 days, $500,000 liability coverage, and the landowner’s written permission if different from the animal owner. Those conditions do not apply to every ordinary pet fence.

• Local sewer and private systems: Occupied property abutting a public sanitary sewer, with the sewer within 100 feet of the property line, must connect within 90 days after official notice. Where public sewer is unavailable, §710.050 requires a private system with the Public Works Manager’s written permit, plans/information and applicable permit/inspection fee. Notify the Manager before covering underground work; inspection is within 48 hours after receipt, and the permit is effective after the Manager is satisfied. When public sewer becomes available, connect and abandon/fill the old septic system or cesspool. The owner maintains a sanitary system at personal cost and follows additional Public Works requirements. Polluted natural-outlet discharge is prohibited without suitable treatment.

• State onsite-system acreage conditions: Missouri §701.031 excludes the owner of a single-family-residence lot of at least 3 acres, or the owner of a residential lot of at least 10 acres with no single-family-residence onsite sewage system within 360 feet of any other onsite sewage system and no more than one single-family residence per ten acres in the aggregate, from the stated state onsite provisions only when the remaining conditions are met. The exclusion does not cover lots adjacent to lakes operated by the Corps of Engineers or a public utility. Every point of the system must be more than 10 feet from any adjoining property line. No effluent may enter adjoining property, contaminate surface water or groundwater, or create a nuisance as determined by a readily available scientific method. Section 701.047 permits more restrictive local standards. These state conditions do not waive the separate local sewage program. The state’s $90 onsite application fee is suspended from August 28, 2026; local fees are not suspended by that state action.

• An existing lawful lagoon: Where the state lagoon rule applies, the pond area needs a fence at least 4 feet high, made of welded, woven or chain-link wire no smaller than 14 gauge. Cattle or hog panels may be substituted with tee line posts. Posts must be pressure-treated wood, galvanized and/or painted steel, and driven, tamped or set in concrete. Line posts must be no more than 10 feet apart; corner posts must be properly braced. The suggested depths are 18 inches for line posts and 24 inches for corner posts. Construction must be sound with no bottom gaps or openings.

• Lagoon fence location and gate: The fence cannot be closer to the water’s edge at the 3-foot operating depth than the center of the berm. Placement exactly on the berm center is not required. The rule recommends that setbacks not exceed 30 feet from the water’s edge. A properly hinged 4-foot-high gate of comparable material needs an effective latch. A 36–48-inch gate width is recommended for mowing and maintenance access. The fence must be complete before dwelling occupancy. Post depths, maximum water-edge setback and gate width are recommendations; fence height, bracing, maximum line-post spacing and effective enclosure are requirements. These provisions do not authorize a new lagoon where local law prohibits one.

• Licensed family child-care outdoor areas: For licensed family child-care homes, an outdoor play area must be available on or adjoining the property, convenient and accessible without hazard. Fencing is required where needed to protect children from traffic, water or other hazards. Homes initially licensed after the rule’s effective date, and new fences installed at existing facilities, need a fence at least 42 inches high. Independently, all fences must prevent children from crawling or falling through, or becoming entrapped.

• Licensed family child-care pools: Swimming and wading pools must be fenced to prevent children’s access. For family homes initially licensed after the rule’s effective date, the pool fence must be at least 42 inches high with a locked gate. The state rule allows an above-ground-pool option of a 42-inch fence around the pool top with barricades at the steps to the pool deck. Applicable local pool rules can be stricter; the licensing provision does not reduce their requirements.

PRIVATE RESTRICTIONS

Recorded covenants, homeowners-association requirements, easements and private boundary or maintenance agreements can add obligations. City approval does not establish a property boundary, decide shared-fence ownership, settle neighbor cost shares or authorize obstruction of recorded access. Agricultural partition-fence duties depend on the applicable Missouri system and facts; there is no general assumption that every residential fence cost must be divided between neighbors. Approved planned-development agreements remain property-specific.

REVIEW AND ENFORCEMENT CONTEXT

Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:

• Approvals and site work: District fence permits, pools, grading, floodplains and applicable development agreements.

• Placement and visibility: Front building lines, corner and through lots, marked sight areas, easements, storm structures and drainage.

• Construction and upkeep: Material and height branches, chain-link attachments, damaged fences, bamboo, pool access and conditional animal enclosures.

• Private rights: Boundaries, ownership, covenants, easement terms and shared costs remain separate from city enforcement.

USING THIS INFORMATION

This page provides general orientation on how residential fence rules are structured and applied within the City of St. Peters, Missouri. Updated November 2026.

In addition to local fence rules, certain Missouri laws apply statewide. See Statewide Fence Laws in Missouri.

It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with the identified municipality, including its actual municipal or county class, charter, adopted program or special district, and each function’s verified territory, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Missouri law. Applicable requirements depend on the property’s actual facts and the respective authority of the identified offices. Private agreements and recorded rights remain separate from government approvals. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern.