FENCE RULES – CAPE GIRARDEAU (CITY), MISSOURI

OVERVIEW

This page covers residential fences inside the City of Cape Girardeau, Missouri. City limits and the property’s zoning and historic-overlay status determine the local rules; a Cape Girardeau mailing address alone does not establish city jurisdiction.

Cape Girardeau requires a fence permit for a new fence or extension and for repairs or replacement exceeding 30 percent of the fence area. For an ordinary non-rural residential lot, the primary front-yard limit is 3 feet and at least 50 percent open; secondary front yards, side yards and rear yards allow 6 feet. Rural-estate and agricultural uses have a different front-yard standard. Placement on a boundary, in an easement or right-of-way, and near an intersection has specific approval conditions. Pools, the Boulevard Local Historic District, drainage and recorded private rights can change the answer. Updated November 2026.

Quick questionCape Girardeau answer
Permit or approvalA fence permit is required for construction, installation or extension, and repair/replacement exceeding 30% of fence area. Narrow temporary-fence and public-improvement exceptions apply.
Typical fence heightOrdinary non-rural residential: 3 feet, at least 50% open in the primary front yard; 6 feet in secondary front, side and rear yards. Agricultural/rural-estate front yards: 5 feet, at least 50% open.
Placement & property linesOn/across a line requires common ownership or submitted written neighbor permission. Easement/right-of-way placement and fences within 30 feet of a street intersection, measured from the right-of-way line, require City Manager approval.
Common fence materialsWood: conventional rigid material. Vinyl/PVC: conventional rigid vinyl is listed, with historic-overlay restrictions. Chain-link: not generally prohibited for an ordinary residential yard; commercial front yards, historic sites and pool openings have separate restrictions.
Important local conditionsFence rules may be further affected by pool barriers, corner and through lots, easements, stormwater and floodplain permits, historic overlays, special uses, utilities and recorded restrictions.
Official local resourceCape Girardeau’s permit forms and fence regulations

The table summarizes ordinary rules. The sections below preserve the use, location, approval and design conditions that qualify them.

GOVERNANCE

Cape Girardeau is a constitutional home-rule city; its charter took effect April 12, 1982. City fence rules apply within its corporate limits, separately from unincorporated county rules. Chapter 25, Article VI regulates fences, while Chapter 7 contains the adopted construction, pool and property-maintenance codes.

The City Manager administers the fence ordinance’s applications, specified placement approvals and discretionary determinations. Community Development/Inspection Services receives fence and residential-pool applications and administers covered construction inspections. Engineering handles the stormwater and floodplain processes described below. The Historic Preservation Commission reviews covered work in local historic districts and at local landmarks.

The city adopts the 2015 International Residential Code, 2015 International Swimming Pool and Spa Code and 2015 International Property Maintenance Code with local amendments. The local residential amendment deletes the model’s fence-permit exemption; the unamended model’s seven-foot exemption is therefore not an ordinary Cape Girardeau fence-permit answer.

PERMIT AND APPROVAL REQUIREMENTS

• New work and replacement: A fence permit is required for construction, installation or extension of any fence, and for repair or replacement when the work exceeds 30 percent of the fence area. The article itself covers all construction, installation, extension, repair and replacement. Work must comply with the approved permit; the City Manager can require inspections. Fence permit fees follow the City Fee Schedule. The permit section does not apply to fences forming part of a public improvement project.

• Application and inspection: The fence application requires two site-plan copies showing the north arrow, structures, setbacks, property lines, easements and widths, streets, driveways, sidewalks, existing fences and retaining walls, and the proposed fence type, height, post depth and diameter. A complete application precedes a minimum five-business-day review. The application states a six-month permit expiration and requires the inspection before concrete is placed.

• Pools: Residential pools have a separate permit application. Its scaled site plans identify easements, setbacks, adjacent streets, drainage, grades, property lines, the fence, direct-access door alarms and the pool’s relation to buildings on the same and adjoining property. Two detailed plan sets demonstrate the adopted-code compliance; required foundation/soil information and licensed-design calculations for departures from conventional pool-code construction accompany the application. A complete application precedes the minimum five-business-day review.

• Engineering approvals: A floodplain permit is required before a building, structure or obstruction is erected, added to or altered, or grading/fill occurs in a designated flood hazard area. Engineering also requires stormwater plans and a stormwater-management permit for development without approved improvement plans before the building permit. Its land-disturbance guidance separately addresses disturbance of one acre or more, including a qualifying larger common plan. These are site/work-dependent processes, not a new fee or blanket extra permit for every fence.

• Historic approvals: Covered construction, alteration, removal or demolition in a local historic district or at a local landmark requires the Historic Preservation Commission’s Certificate of Appropriateness. The Boulevard guidelines treat existing properties as grandfathered as-is until future actions fall under the guidelines; they do not require every existing fence to be retrofitted merely because the overlay exists. A historic approval does not replace the ordinary fence permit.

• Temporary fences: The listed temporary erosion-control, construction/demolition or burned/condemned-site security, special-event parking/security, and government security/traffic-control fences are exempt only from the fence-permit section, commercial-sign prohibition, post-depth rule, height/surface section and conventional-material subsection. Other applicable placement, drainage, access and safety rules remain. Temporary fences must be removed promptly after their activity or event, as determined by the City Manager.

FENCE PLACEMENT RULES

• Property lines: A fence cannot be on or across a property line unless the same owner owns both properties or the other owner gives written permission and a copy accompanies the permit application. Where it crosses a line, two mounting posts must abut at that line. The fence owner is responsible for locating property lines. Utility marks do not establish a boundary, and a surveyor’s real-property report is not the boundary-survey/construction product for locating a new fence.

• Survey monuments and markers: Missouri §60.355 prohibits knowingly moving, removing, defacing or destroying a United States Public Land Survey System corner, property-boundary marker, benchmark or horizontal-control monument, with the exception for a land surveyor registered under Chapter 327. It provides a class B misdemeanor classification, the cost of reestablishing permanent monuments and markers, and the affected real-estate owner’s reasonable surveying costs and attorney fees in the stated civil action. Fence work does not authorize moving a protected marker.

• Easements, streets and drainage: No fence or portion may be in an easement or a public street/alley right-of-way without the City Manager’s approval. Authorized access to utilities and stormwater-drainage infrastructure cannot be impeded; neither can stormwater flow. Public approval does not erase the underlying easement or private access right.

• Intersection visibility: No fence or portion may be within 30 feet of a street intersection, measured from the right-of-way line, without City Manager approval. This is a fence-location approval condition, not permission to place a short fence anywhere inside an assumed pavement-edge triangle.

• Utility and emergency access: A yard cannot be completely enclosed in a manner that impedes emergency access. The application warns that utilities can lie in street rights-of-way as well as easements. Requested utility relocation needs utility approval and is at the owner’s expense; a fence in an easement remains subject to removal or modification for utility access.

• Roads and drainage: Missouri §229.150 prohibits the covered willful and knowing road obstruction or damage, including fencing across or upon the right-of-way and the specified drainage obstruction, subject to its soil-and-water-conservation and precision-land-grading exceptions. Its removal process includes tracked notice, 30 days, a court petition and an opportunity for hearing before authorized entry; it is not unrestricted private entry. Existing drainage and utility easements retain their own rights. A fence may also be affected by a drainage or levee district’s lawful works and acquisition framework.

• Missouri excavation notice: Covered fence-post digging, augering, boring and driving are excavation, including on private land. Notice through Missouri 811 is ordinarily due at least 2 but no more than 10 working days before the expected start. The two-day clock begins at midnight following receipt and excludes Saturdays, Sundays and legally declared state or federal holidays. The notice identifies the excavator, work location, expected start, depth, type and other required information. Separate private lines are not guaranteed to be located by participating utilities. Utility markings do not establish the property line or grant access rights.

• Responses and a second notice: Operators ordinarily provide locations or a no-facilities response within two working days unless the excavator agrees to an extended start through the center. Work cannot begin before the scheduled date unless all facilities have been confirmed located. An unanswered compliant original notice requires a second notice; the operator then has 2 hours to mark or contact the excavator with its marking time. A no-response notice by 2 p.m. requires marking that working day; a later one requires marking by 10 a.m. the next working day. Only the statute’s failure-to-mark-or-contact conditions permit starting after that process, with the duty of care preserved. A clarification meeting is held within two working days; trenchless-work notice also carries the available-depth-information duty.

• Notice duration and careful excavation: A notice expires at 11:59 p.m. 21 consecutive calendar days from the work start date. Work within the notified area may continue while it is valid and the marks remain visible. Not beginning within the stated ten-working-day period requires a relocate request; unusable marks require remarking through the original process and timing. Excavators must reasonably preserve marks and can bear reasonable unnecessary remarking costs. The approximate location normally includes the facility width plus 2 feet on each side, with a wider designation for the specified unusual conditions. Horizontal and vertical confirmation practices must suit the site, using hand or soft digging when possible. The sixteen-inch agricultural-tilling and marking-stake exclusions are not structural fence-post exemptions.

• Unmarked facilities, damage and emergencies: An incorrectly located or unmarked facility requires center notification and a two-hour operator contact or correction response. Damage, dislocation or disturbance, including protective wires and items, must be reported; pipeline contact or damage releasing gas or hazardous liquid requires an immediate 911 call. Damage cannot be concealed, and repairs require owner authorization, except the narrow temporary sewer-emergency repair after notification to prevent further damage. Genuine emergency excavation requires reasonable precautions and notice as soon as practical; the operator has the statutory two-hour mark/contact duty. State-highway excavation separately requires the commission’s permit, subject to its railroad-right-of-way exception.

• Public division-fence rights: Missouri’s general and local-option partition-fence systems have different livestock, allocation, contribution and repair procedures. Local option takes effect through the required county election and adoption order. General-law no-need relief and later livestock-use contributions differ from local-option half-value and special-fence procedures. Recorded allocations can bind successors. General-law repair entry concerns the owner’s division-fence portion; general removal requires all owners’ consent except a public-road opening, while local option also states a repair exception. Section 537.350 separately covers removal without six months’ notice to an adjoining owner of cultivated fields, with its damage remedy and §537.360 probable-cause limitation. A permit or an ordinary privacy fence does not automatically create a neighbor half-cost duty.

FENCE HEIGHT AND VISIBILITY RULES

• Ordinary residential yards: For non-rural-estate residential use, the primary front-yard maximum is 3 feet with at least 50 percent open surface. Secondary front yards and side/rear yards have a 6-foot maximum. On a lot with more than one front yard, the primary one is the yard toward which the principal dwelling’s main entrance is oriented; another front yard is secondary. A corner or through lot does not automatically have the same three-foot rule on every frontage.

• Agricultural and rural-estate yards: Agricultural and rural-estate residential front yards allow 5 feet, at least 50 percent open; side/rear yards allow 6 feet. Rural-estate residential means residential use in a rural-estate residential district. The parcel’s actual use and zoning classification govern this branch.

• Measuring the height: Height runs from ground to the highest boards, pickets, panels or other elements between vertical supports. Posts and other vertical supports, including finials, can exceed that fence height by no more than 15 percent. Mounds, slopes or terraces cannot be created to elevate ground at the fence line above the adjacent yard.

• Other uses on or beside residential property: The enacted table allows commercial front-yard fences up to 4 feet and 50 percent open, and commercial side/rear fences up to 8 feet; manufacturing/industrial yards allow 8 feet. School/park playground front fences allow 6 feet and 75 percent open, with 6 feet side/rear. Athletic-field fences allow 12 feet, with 75 percent open in front; baseball backstops are exempt. Tennis-court fences allow 12 feet and 50 percent open in all yards. Unlisted uses follow the most similar listed use, as determined by the City Manager. Pool fences follow Chapter 7, Article IIIa.

• Pool-barrier height: Under the adopted 2015 pool framework, a required barrier must be at least 48 inches above outside grade around the entire perimeter. That height remains available for a 3-foot horizontal distance outward from the barrier; the three feet is the height-measurement zone, not fence width. Gate, opening, clearance and alternative-protection conditions remain part of the same framework.

• Boulevard placement and visibility: In the Boulevard Local Historic District, fences are restricted to side and rear yards and cannot extend past the front building line; no fence of any type is allowed in the front yard. A street-visible side/rear fence must match the house’s architectural style and period, including color. This overlay is distinct from the ordinary three-/six-foot zoning table.

MATERIAL AND CONSTRUCTION LIMITS

• Ordinary materials and appearance: Conventional rigid wood, metal, vinyl, brick and stone are listed materials; the City Manager may approve others case by case. Materials, finish and design must be visually compatible with the property and surrounding properties. The front or finished side faces outward. Chain-link is not generally prohibited for an ordinary residential yard; the enacted table’s front-yard chain-link prohibition is attached to commercial use, while pool and historic restrictions have their own scope.

• Posts, repair and maintenance: In-ground posts need an embedded depth equal to one-half the fence height and a hole diameter three times the post diameter. Fences must be built in a workmanlike manner and maintained upright. Missing components must be replaced within the City Manager’s required time with matching or comparable material, style and finish. The property-maintenance framework separately requires structural soundness and good repair, and local protective-treatment provisions cover exterior fences and non-decay-resistant wood.

• Electric fences: Electrical connection is prohibited except for garden/orchard fences with input not exceeding 12 volts and fences nonlethal to humans in agricultural districts. These are specific exceptions, not permission for an electrified privacy fence in any residential yard.

• Barbed and razor wire: Barbed wire is allowed atop a fence at least 4 feet high for agricultural uses, or at least 6 feet high for manufacturing/industrial uses and the listed utility, telecommunications, airport and government security facilities. Razor wire is allowed only for the listed industrial/security uses atop a fence at least 6 feet high. Except for the specified public-utility/telecommunications/airport/government-security branch, both are prohibited adjacent to an elementary or middle school or commercial daycare. Neither may project into a public street/alley right-of-way or over a public sidewalk.

• Signs: Commercial signs cannot be displayed on fences except those used with school or public athletic fields. The listed temporary-fence exception has the narrower cross-reference stated above; an ordinary yard fence does not acquire that exception merely because it is movable.

• Boulevard materials and adjacent work: Modern plastic fencing is unacceptable when visible from the street in the Boulevard district. Chain-link is unacceptable except for small dog pens in rear yards. The Commission considers fence applications case by case, with a material sample, height, placement sketch and house photograph. Retaining walls retain their period character and are repaired/replaced with like materials; new walls use native stone, brick or like suitable modern material. Construction, including fences, must avoid tree/root damage; tree-retention and like-tree replacement provisions also apply.

• Pool gaps, surfaces and openings: The 2015 pool framework limits ground clearance to 2 inches over nonsolid ground, such as grass or gravel, or 4 inches over a solid surface, measured outside. A barrier mounted on an abovegrade pool/spa structure has a maximum 4-inch structure-top-to-barrier-bottom gap. Openings must reject a 4-inch sphere. Solid surfaces cannot have climbable handholds or footholds apart from normal construction tolerances and tooled masonry joints.

• Pool pickets, chain-link and diagonals: With horizontal-member tops less than 45 inches apart, horizontal members go on the pool side, and vertical gaps and decorative cutouts cannot exceed 1¾ inches. At 45 inches or more, vertical gaps can be up to 4 inches, while decorative cutouts remain limited to 1¾ inches. Chain-link openings cannot exceed 1¾ inches, including slat-reduced openings with the slats fastened top and bottom. Diagonal openings have the same 1¾-inch maximum and an angle no greater than 45 degrees from vertical.

• Mesh pool barriers: Mesh fencing follows the manufacturer’s instructions. Its bottom sits no more than 1 inch above the surface or grade; it cannot be lifted more than 4 inches and cannot admit a four-inch sphere beneath a panel. Section attachments must be at least 45 inches above grade with the required secure device. Hinged gates follow the gate rules, patio post sleeves are nonconductive, and mesh fencing cannot be mounted atop an onground residential pool.

• Pool access and clearances: A 36-inch exterior clear zone separates the barrier from climbable permanent equipment or structures. The pool-side barrier is at least 20 inches from the water’s edge. Access gates accommodate locks; pedestrian gates open away from the pool and are self-closing and self-latching. Utility/service gates stay locked when unused. Multiple gates require a secured leaf and adjacent self-latching leaf, with no opening over ½ inch within 18 inches of the release. When a latch release is below 54 inches from grade, it goes on the pool side at least 3 inches below the gate top, with the same half-inch/eighteen-inch protection.

• Onground pool walls and natural barriers: An onground pool wall can serve as a barrier when permitted by the manufacturer, on grade and at least 48 inches high around its perimeter, with the remaining barrier requirements met. A top-mounted barrier retains the required forty-eight-inch overall height and manufacturer’s installation. Access ladders/steps must be secured, locked or removed unless separately enclosed; resulting openings cannot admit a 4-inch sphere. For a natural water boundary, the special no-shoreline-barrier option requires no allowed public shoreline access and barriers extending at least 18 inches beyond the water edge. Natural topography requires governing-body approval and equivalent protection.

• Horizontal balusters: The city expressly prohibits horizontal balusters wherever guards or barriers are required. That local amendment qualifies the model’s general horizontal-member configurations; it is not a ban on every horizontal board in an ordinary yard fence.

• Pool covers and building walls: Spas and hot tubs have a model exception for a lockable ASTM F1346 safety cover. The 2015 model also excepts swimming pools with a powered safety cover complying with ASTM F1346. Cape Girardeau proposed repealing that cover-only exception; its current local status needs City confirmation before relying on a cover alone. Where a building wall forms part of the barrier, direct-access doors and operable windows with sills below 48 inches above inside finished floor need the specified UL2017 alarm, an ASTM F1346 listed/labeled cover, or approved equivalent protection. Alarm-deactivation controls are at least 54 inches above floor in ordinary units, or 48–54 inches above floor in the stated accessible unit types.

• Existing pool enclosures: The adopted property-maintenance code requires private pools, hot tubs and spas containing water more than 24 inches deep to be surrounded by a barrier at least 48 inches above finished ground on the side away from the pool. Gates and doors must be self-closing and self-latching and must positively close and latch when released from an opening 6 inches from the gatepost. An existing enclosure cannot be removed, replaced or changed so its safety effectiveness is reduced. The section retains its complying ASTM F1346 spa/hot-tub safety-cover exception.

• State lagoon enclosure construction: Where the state residential lagoon rule applies, the fence must be complete before dwelling occupancy and at least 4 feet high. Welded, woven or chain-link fence uses 14-gauge-or-heavier wire; cattle or hog panels can substitute with tee-post line posts. Pressure-treated wood or galvanized/painted steel posts must be driven, tamped or concrete-set, with line posts no more than 10 feet apart, braced corners and no bottom gaps. The gate must be properly hinged, 4 feet high, comparably constructed and effectively latched.

• Lagoon fence position and recommendations: The fence must be no closer to the operating water edge than the berm center, measured with water at the 3-foot operating depth. Three feet describes water depth, not a horizontal fence setback. The rule recommends line-post depth of 18 inches, corner-post depth of 24 inches, a fence no more than 30 feet from the water edge, and a 36–48-inch gate width. Those recommendations use “should”; they are distinct from the mandatory fence, spacing, bracing and gate duties.

• State onsite scope: Section 701.031 has a qualifying single-family 3-acre branch and a separate 10-acre residential-lot branch requiring no single-family residential sewage system within 360 feet of another onsite system and no more than one single-family residence per ten acres in the aggregate. The specified Corps of Engineers and public-utility lake-adjacent lots are excluded from those exemptions. Every system point must be more than 10 feet from adjoining property lines, without effluent trespass, groundwater or surface-water contamination, or the scientifically determined nuisance. Current state administration and stricter local standards remain separate.

• Livestock restraint: Section 270.010 separately requires restraint or enclosure of the specified horses, mules, asses, cattle, swine, sheep and goats. A private person may restrain stock found outside its owner’s enclosure; a sheriff or other officer with police powers must do so on seeing it or receiving notice. Within 3 days, the person or officer must give a known owner written notice stating the feeding/keeping compensation and damages claimed. The owner owes reasonable taking-up, keeping and feeding compensation and actual damages. If the owner is unknown, or is notified but fails to pay taking-up, feeding and keeping compensation, the animals are dealt with as strays under the stray law. Its public-road branch preserves the defense based on absence of the owner’s fault or negligence. Those duties are separate from the partition-fence cost rules and do not make every residential fence a livestock enclosure.

• Licensed family childcare homes: At a licensed family childcare home, the outdoor play area must be on or adjoining the premises and accessible without hazards. Fencing is required where necessary to protect it from traffic, water or other hazards. For homes initially licensed after the rule’s effective date and new fences at existing facilities, the minimum is 42 inches. Fences must prevent crawling or falling through and entrapment. Pools and wading pools require child-excluding fencing; the stated initial-license cohort requires the forty-two-inch fence and a locked gate. An aboveground alternative places the fence around the top with barricaded steps. Hazardous animals must be securely penned and inaccessible to children. These licensed-home conditions do not create an ordinary-home forty-two-inch rule.

• Other rural or protected uses: A permitted captive-cervid enclosure has its own state fence, gate and maintenance standards; a garden fence excluding wild deer is a different use. Defined large-carnivore possession has a separate permit regime. State-park livestock/game boundary participation requires the written request, approval and cost/maintenance arrangement, rather than subsidizing ordinary privacy fences. Qualifying abandoned family burial grounds have statutory fence protection and reasonable landlocked visitation rights. The applicable permit, boundary or protected-site facts determine these uses.

PRIVATE RESTRICTIONS

Recorded covenants, homeowners-association architectural rules, private easements and enforceable fence-location, maintenance or cost agreements may apply in addition to city requirements. Their actual wording and applicable Missouri law govern. A city permit, neighbor’s written placement permission or historic approval does not automatically release a separate recorded restriction.

A fence’s age or location alone does not establish ownership or adverse possession. A gate does not automatically make interference with an easement permissible. Partition-fence contribution and repair/removal rights remain separate from city permits and private agreements.

REVIEW AND ENFORCEMENT CONTEXT

Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:

• Fence permits and inspections: New or extended fences, repair/replacement triggers, approved plans, post inspections, heights, materials and upkeep.

• Site and special-use review: Easements, rights-of-way, intersection approvals, drainage/floodplain work, pool safety and historic-overlay work.

• Private property rights: Ownership, access, covenants and shared-fence disputes remain distinct from municipal code approval.

USING THIS INFORMATION

This page provides general orientation on how residential fence rules are structured and applied within Cape Girardeau, Missouri. Updated November 2026.

In addition to local fence rules, certain Missouri laws apply statewide. See Statewide Fence Laws in Missouri.

It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with the identified municipality, including its actual municipal or county class, charter, adopted program or special district, and each function’s verified territory, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Missouri law. Applicable requirements depend on the property’s actual facts and the respective authority of the identified offices. Private agreements and recorded rights remain separate from government approvals. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern.