FENCE RULES – RAYTOWN (CITY), MISSOURI
OVERVIEW
This page covers residential fences inside the incorporated City of Raytown, Missouri, in Jackson County. A Raytown mailing address does not by itself establish that a property is within the city limits.
Raytown’s ordinary residential fence rules make the yard and street frontage central to the design. In R-1, R-2 and R-3 districts, side and rear fences generally stop at six feet, while fences in front of the principal building are limited to three and one-half feet. Corner and through lots have specific street setbacks, and chain-link cannot be used in every yard. Fences not over six feet have a residential building-permit exemption, but zoning and applicable site approvals still govern. Private pools, seasonal garden fences, utility easements and designated design areas add distinct requirements. Updated November 2026.
| Quick question | Raytown answer |
|---|---|
| Permit or approval | Residential fences not over 6 feet are exempt from the building permit. Zoning, historic, floodplain, grading and right-of-way requirements remain separate. |
| Typical fence height | In R-1/R-2/R-3: 6 feet in side and rear yards; 3½ feet in front, with stated corner/through-lot exceptions. Front-setback fences at that lower height need 40 percent open surface. |
| Placement & property lines | R-1/R-2 expressly allow property-line fencing subject to other rules. Six-foot street-frontage exceptions require 10 feet from the right-of-way. Visibility, easements, drainage and pool conditions remain. |
| Common fence materials | Wood: not separately classified by the general residential fence rule. Vinyl/PVC: not separately classified. Chain-link: prohibited in front yards and street-abutting side/rear yards in R-1/R-2/R-3. Design areas and pool barriers have additional material rules. |
| Important local conditions | Fence rules may be further affected by corner and through lots, private pools, seasonal use, lawful nonconformities, utility and drainage easements, floodplain or grading work, historic and design-area requirements, animal uses and private restrictions. |
| Official local resource | Raytown Building Permits |
The table summarizes the ordinary framework. The following sections explain the conditions, exceptions and site-specific branches that determine how those rules apply.
GOVERNANCE
Raytown is a fourth-class city. Its Board of Aldermen adopts municipal ordinances, and the Community Development Department administers zoning and construction requirements within the city. The City’s Municipal Code resource provides access to its ordinances. The adopted construction framework includes the 2018 International Residential Code, International Building Code and International Property Maintenance Code, with local amendments, and the 2017 National Electrical Code.
The residential code also incorporates the 2018 International Swimming Pool and Spa Code for pool and spa design and construction. Raytown adds its own outdoor-barrier provisions to the residential code. Those local provisions govern direct conflicts with the referenced code; nonconflicting pool requirements still apply. Zoning enclosure and pool-location requirements operate separately.
The Public Works Department administers city right-of-way work. The City Engineer administers grading and the mapped floodplain program. The Planning Commission handles the stated historic and design reviews, and the Board of Zoning Adjustment hears applicable zoning appeals and variances. Animal Services administers animal cases. An approval from one office does not replace another required approval or establish private property rights.
An approved planned-development overlay, a historic designation, the Central Business District design area or the Highway 350 Corridor can affect the property. For a Conservation-zoned or Historic Preservation property within the Highway 350 area, Community Development determines the applicable corridor coverage. Agricultural or animal uses and residential uses accessory to a commercial use likewise depend on their current use and approval conditions; none creates a general exemption from the ordinary fence rules.
PERMIT AND APPROVAL REQUIREMENTS
• Ordinary fence permits: The locally amended residential-code permit exemption covers fences not over six feet high. Exempt work must still comply with zoning, pool barriers and other applicable requirements. The exemption does not authorize a fence above a zoning maximum or eliminate a separate site approval.
• Repair and replacement: A lawful nonconforming fence may be maintained, but its height or length cannot increase unless the increase conforms. It may be replaced if the replacement material is not prohibited, the fence does not and will not create a safety hazard, and its height and length do not increase except in conformity. These provisions apply to a legal nonconforming fence, not every existing fence.
• Required permit applications: Where a construction permit is required, the City uses a completed application and supporting plans for code and zoning review. An owner may obtain the construction permit only when the owner holds title, lives on the property and personally performs the work. Otherwise, a licensed contractor obtains the permit and performs the work.
• Grading: Lot grading requires a permit from the City Engineer and a plot plan showing the extent by contour elevation, the accurate locations of utilities and below-ground improvements, and the proposed grading. Fill deeper than 12 inches must be compacted to the density specified by that office. The Engineer may determine that grading minor in nature does not need a permit.
• Land disturbance: The land-disturbance ordinance separately exempts installation of fence posts and other specified posts or poles. Its exemptions also include minor home gardens, home landscaping, repairs and maintenance, stated agricultural tilling and other disturbance under 1,000 square feet. Broader clearing, grading or excavation can require the applicable land-disturbance permit and stormwater pollution prevention plan. A land-disturbance exemption does not replace a separate grading or floodplain approval.
• Mapped floodplain work: Construction or other development in the mapped numbered or unnumbered A and AE flood-hazard areas requires a separate floodplain development permit. The City Engineer administers the program using the January 20, 2017 flood insurance rate maps, as amended and subsequently revised. The written application identifies the property, work, intended use, assessed and improvement values, floodway or fringe location, existing base-flood and proposed elevations, plans and specifications, signature and other reasonably required information.
• Designated historic properties: Historic appropriateness review applies to exterior construction, alteration or removal requiring a building permit on a designated landmark or historic property and its stated environs. It also applies to a significant exterior architectural or historical feature identified in the designation, even where that work has no building-permit trigger. That latter feature-based requirement excludes environs and minimal repairs needed to prevent further loss after accident or natural causes. The Planning Commission decides within 45 days, with written notice within seven days. An appeal goes to the Board of Aldermen within 15 days after notification; the Board acts within 30 days and holds a public hearing.
• Historic economic-hardship alternative: A certificate of economic hardship is an alternative wherever a certificate of appropriateness would otherwise be required, providing relief where the chapter would impose undue hardship. Relief is not automatic. Before deciding, the Planning Commission may solicit expert testimony or request estimates of proposed work and added compliance costs; a qualified or bonded rehabilitation professional’s report on structural soundness and suitability for rehabilitation; estimated market values under the existing, proposed and recommended-work conditions; and, for demolition, the economic feasibility of rehabilitation or reuse. It may also request applicable ownership and financial information, including the previous two years of income, operating and maintenance expenses, depreciation and cash flow for income-producing property; the remaining mortgage or secured-financing balance and the previous two years of annual debt service; appraisals obtained within the previous two years; sale or rental listings, asking prices and offers within the previous two years; the two most recent assessments; the previous two years of real estate taxes; form of ownership or operation; and other information needed to determine reasonable return. A person dissatisfied with the determination may appeal to the Board of Aldermen within 15 days after notification. The Board must act within 30 days of receipt and hold a public hearing. This historic alternative is separate from the Highway 350 physical-impossibility process.
• Design-area review: In the defined Central Business District, a residential improvement addressed by the design standards is reviewed as to that improvement. A full development site plan is not automatically required for every ordinary fence. Gated parking facilities and requests for alternatives to design standards have their stated preliminary-plan review; where no preliminary plan is required, the Director receives a plot plan and information sufficient to determine compliance. Approved development plans and property-specific conditions remain applicable.
• Temporary construction and event fences: Construction-site fencing cannot be erected before the grading or building permit is issued and must be removed before the final certificate of occupancy. It may exceed six feet with Community Development Director approval and compliance with applicable building codes. Festival, special-event and other temporary or seasonal fences require the Director’s approval of a site plan, apart from the expressly regulated garden-fence branch.
• Public rights-of-way: Any construction in city right-of-way requires a Public Works right-of-way permit. Public-way permission remains separate from the right to fence one’s own lot. Excavation within a state highway or its right-of-way has a separate Missouri Department of Transportation permit requirement, subject to the statutory railroad-right-of-way exception.
FENCE PLACEMENT RULES
• Property lines and districts: In R-1 and R-2 districts, the fence ordinance expressly allows fencing along any property line, subject to the remaining rules. The corresponding property-line sentence does not name R-3, although R-3 shares the residential height and design rules; Community Development determines the R-3 placement application. A property-line allowance does not convey a neighbor’s land or override an easement, public right-of-way or sight restriction.
• Corner and through lots: On a corner lot, a fence up to six feet may occupy the front setback facing the side street if it is at least ten feet from that street’s right-of-way line. On a through lot, the same six-foot allowance applies in the front setback along the street behind the principal building, with the same ten-foot right-of-way setback. Intersection visibility still applies.
• Other zoning districts: Outside R-1, R-2 and R-3, side- and rear-yard fences are allowed subject to other requirements. Front-yard fences are prohibited except on property abutting Highway 350 for the stated trash, storage and service-area screening. That exception permits the specified screening within ten feet of the highway right-of-way under the Highway 350 design standards; it is not an ordinary front-yard privacy-fence allowance.
• Plats and recorded conditions: Recorded subdivision lines can establish the applicable yard or setback where the qualifying plat predates the ordinance and has not been officially vacated. A building setback is not automatically a fence setback. Recorded utility and drainage easements and approved site conditions can independently limit placement and preserve access.
• Utility and drainage easements: The City prohibits permanent fixtures or structures on recorded utility easements. Improvements classified as temporary, including fences, may be disturbed or removed when the City needs to do so, at the property owner’s cost. Private easement terms and access rights remain separate. Subdivision drainage easements preserve the space and access established for that drainage system; their design widths do not create one universal setback on every existing residential lot.
• Floodplain placement and drainage: Covered floodplain development must use adequate design or anchorage against flotation, collapse and lateral movement, flood-resistant materials and methods that minimize damage. Before a floodway is designated, cumulative development cannot increase the base-flood water surface by more than one foot. In a designated floodway, an encroachment requires engineering certification that it will cause no increase in flood levels during the base-flood discharge. Altered or relocated watercourses must retain their flood-carrying capacity.
• Pool location: Private pools more than two feet deep must be behind the front building line, at least ten feet from rear and side lot lines, and, on a corner, at least 15 feet from the side-street line and 20 feet from a principal building on an adjoining lot. A side-yard pool must be at least 40 feet from the front line and 15 feet from the side line. Pool drainage plans require approval by the Director or another duly qualified individual. These dimensions locate the pool; they are not a blanket setback for every fence. The pool-side barrier also has the water-edge separation described below.
• Animal housing enclosures: A dog or cat housing pen or other enclosure, except a fence, cannot be within ten feet of a property line or 15 feet of a human-occupied building other than the keeper’s dwelling. This does not impose a ten-foot setback on every yard fence. The permitted animal use and any current special conditions remain a separate Animal Services or Community Development matter.
• Seasonal gardens: A garden fence cannot be between the side of the house containing the front entrance and a street right-of-way. It cannot be installed before April 1 and must be removed by November 1 each year.
• Survey markers: Missouri Section 60.355 protects the listed public-land-survey corners, property boundary markers, benchmarks and horizontal-control monuments from knowing movement, removal, defacement or destruction, except by a registered land surveyor. It provides a class B misdemeanor classification, restoration-cost liability and the affected owner’s stated reasonable surveying-cost and attorney-fee remedy. A fence approval does not authorize moving a protected marker.
• Excavation notice: Covered fence-post work includes hand digging, augering and driving. Missouri’s underground-facility law requires notice through the notification center at least two working days, but no more than ten working days, before the expected start. The period starts at midnight following receipt; Saturdays, Sundays and legally declared state or federal holidays do not count. Notice supplies the excavator and responsible person’s contact information, location, start, depth, type of excavation and other required site details. The operating service is Missouri 811. A locate does not establish a boundary, grant entry rights or replace permits.
• Responses and unanswered notices: Operators ordinarily respond within two working days unless an extension is agreed through the notification center. Starting before the scheduled excavation date requires confirmation that all facilities have been located. If an operator fails to respond to proper original notice, a second no-response notice is required before excavation. The operator then has two hours to mark or make the required contact. A second notice received by 2 p.m. requires marking that working day; a later notice requires marking by 10 a.m. the next working day. Excavation may begin only under the statute’s failure-to-mark-or-contact conditions, with the required care still applicable.
• Ticket life and markings: A notice expires at 11:59 p.m., 21 consecutive calendar days from the work start date. Work may continue within its area while the ticket is valid and markings remain visible. Failure to begin within the stated ten-working-day period requires a relocate request before beginning. Unusable marks require a remark request with the original notice timing; reasonable care to preserve markings remains required, with possible reasonable remarking costs for failure of care or unnecessary repeat requests.
• Care near underground facilities: The statutory approximate-location strip ordinarily extends the facility’s width plus two feet on each side, with a wider designation for the stated unusual conditions. Before work, the excavator determines best practices for confirming horizontal and vertical location in the site conditions; hand or soft digging is used when possible. Incorrectly located or unmarked facilities must be reported through the center; the operator responds within two hours by contact or correct locating. Limited tillage and temporary-marker exclusions are not a general fence-post exemption. Separately owned private lines are not a promise of universal locating service.
• Damage and emergency work: Damage, dislocation or disturbance of facilities or their protective items, including trace wires, encasements and protective stakes, must be reported to the notification center. Pipeline contact or damage causing a hazardous-liquid or gas release requires an immediate 911 call. Damage must not be concealed, and repairs require the owner’s authorization. The narrow emergency temporary sewer-repair exception after notification does not remove reporting duties. Genuine emergency excavation retains reasonable precautions and notice as soon as practical; within two hours, the operator marks or contacts the excavator with available information and states when marking will occur if it cannot mark within that time.
• Shared-fence and removal rights: Missouri’s partition-fence systems address their own use, contribution, repair and removal conditions; city approval does not select a system or require a neighbor to pay half of an ordinary yard fence. Independently, Section 537.350 addresses voluntary removal of a partition fence without six months’ written notice to the adjoining owner of cultivated fields, with its stated five-dollar amount, double damages and costs. Section 537.360 limits covered recovery to single damages and costs where there was probable cause to believe the land or thing was the defendant’s own. The notice provision does not itself grant ownership or override any separately applicable consent requirement.
FENCE HEIGHT AND VISIBILITY RULES
• Residential yard heights: In R-1, R-2 and R-3, side- and rear-yard fences cannot exceed six feet. Between the principal building’s front and the street, the limit is three and one-half feet, except for the corner and through-lot branches described above. Fences in the front-yard setback at three and one-half feet or less must have at least 40 percent open surface area. Other fences may be solid unless another applicable rule requires otherwise.
• Measurement and supporting structures: Height is measured vertically from ground level to the top. For a fence on a retaining wall, deck or other structure, ground level is the base of that supporting structure. A fence is not considered atop the other structure if set back at least three feet from its front edge. Outside R-1/R-2/R-3, the general fence maximum is also six feet, subject to applicable design and special-use rules.
• Street and driveway vision triangles: At a street or driveway intersection, nothing may materially impede vision in the triangle between 30 inches and ten feet above the bottom-of-curb grades of the intersecting streets or driveways. Residentially zoned districts use arms of at least 30 feet; other districts use at least 20 feet. Arms are measured from the center of the lot-line intersection and their ends are joined across the lot. Rounded corner lot lines are extended straight to their intersection. The Town Square Overlay District is excepted from this zoning triangle requirement.
• Additional road-design sightlines: A subdivision or road-design sightline governed by the City’s technical standards remains an additional City Engineer determination. It does not replace the ordinary zoning triangle above. The Town Square exception from that zoning triangle does not establish an exemption from every separately applicable road-design sightline.
• Private-pool enclosure height: For the covered private pool more than two feet deep, zoning requires a nonclimbable protective fence or permanent structure at least four feet but less than six feet high around the pool area, separating it from adjoining property. Gates have locks and must be locked when the pool is unattended. This is separate from the technical barrier dimensions and access controls below.
MATERIAL AND CONSTRUCTION LIMITS
• Ordinary materials: The general R-1/R-2/R-3 yard-fence provision does not separately classify wood or vinyl/PVC as expressly approved or prohibited. The same general provision does not provide a separate approval list for composite, bamboo, fiberglass, individual metals, brick, stone, concrete or salvaged materials. That does not remove the express prohibited-material list or applicable design, maintenance and pool conditions.
• Restricted residential materials: Chain-link is prohibited in the front yard in R-1/R-2/R-3. It is allowed beside or behind the structure only when that side or rear yard does not abut street right-of-way. Plywood, electrified wire, barbed wire and razor wire are prohibited, subject to the stated temporary or seasonal fence provisions. Underground “invisible” animal-containment fences are excepted from the electrified-wire ban.
• Finished face and maintenance: Posts, cross supports and other support structure must not be visible from outside the enclosed area unless the Community Development Director specifically approves them as part of the overall fence design. Fences must be properly maintained and kept in good repair.
• Other zoning districts: Outside R-1/R-2/R-3, chain-link is prohibited next to street or highway right-of-way, public parking, or residentially zoned or used property. Electrified and barbed wire are prohibited next to residentially zoned or used property; razor wire is prohibited. Side/rear fences may be solid unless another design standard applies, and exposed supports require the stated design approval. Highway 350 front screening needs additional trees and shrubs between the fence and highway right-of-way to substantially reduce visibility.
• Garden and construction materials: Seasonal garden fencing is limited to three feet high and may use wire or other materials allowed in the applicable district. Its placement and annual installation/removal dates are stated above. Approved construction-site fencing may use any material that does not threaten people or property; the permit timing, height approval and removal conditions remain applicable.
• Central Business District design: For covered Central Business District residential development or redevelopment, front-yard transition elements include low fences no higher than three feet; an element over two feet must be at least 80 percent transparent. New or redeveloped front yards provide at least two listed transition choices, such as steps, a low fence, trellis, site furnishings, a low hedge, landscaped border or low decorative wall, and at least one listed entrance element, such as a gateway, archway, canopy, arbor/trellis, varied paving or pedestrian lighting. Fencing must be durable, weather-resistant and vandal-resistant; chain-link and other wire fences are not allowed. A two-foot fence or hedge maximum is encouraged, not mandatory. Existing single- and multifamily residences are encouraged to incorporate the listed front-yard standards. Low fences, walls, hedges and landscaping are also encouraged to define or screen side and rear outdoor space.
• Highway 350 Corridor design: Where the Highway 350 Corridor fence standards apply, the material list is cedar, redwood, CCA-treated wood, wrought iron, aluminum made to resemble wrought iron, or vinyl made to resemble wood. Design must create variety, for example through a staggered fence line and wrought-iron or masonry columns. Complementing the architecture, following topography and integrating fencing with landscape design are strongly encouraged. A lawful existing nonconformity has its stated continuation treatment. An owner seeking relief for physical impossibility must submit written reasons based only on the property’s physical characteristics before submission of the required site plan and prove physical impossibility by clear and convincing evidence. The Director determines whether physical compliance is possible and recommends accordingly. A determination that compliance is possible may be appealed to the Planning Commission under article XI. Economic hardship is not considered as a reason for noncompliance. The exact Conservation/Historic Preservation overlap remains the Community Development application described above.
• Historic fence work: Historic review retains characteristic fencing, walls and other features reflecting the property’s history. Deteriorated architectural features must be repaired rather than replaced wherever possible. Necessary replacement should match composition, design, color, texture and other visual qualities, using evidence rather than conjectural designs. Compatible accessory features and protection of archaeological resources are part of review. General code standards operate alongside the actual designation and any applicable specific criteria.
• Local pool-barrier dimensions: Raytown’s added residential-code Section 4401 requires an outdoor pool, hot tub or spa barrier at least 48 inches above outside grade, with at most two inches between ground and barrier on that side. A barrier mounted on the pool top has at most four inches between that top and the barrier bottom. Openings cannot pass a four-inch sphere. A solid masonry or stone barrier cannot have indentations or protrusions except normal construction tolerances and tooled masonry joints.
• Pool-barrier members: Where the tops of horizontal members are less than 45 inches apart, those members face the pool and vertical gaps and decorative cutouts are at most one and three-quarter inches. At 45 inches or more, vertical gaps may be at most four inches, while decorative cutouts remain at most one and three-quarter inches. Lattice or other diagonal-member openings are at most one and three-quarter inches; the referenced pool code also limits diagonal members to 45 degrees from vertical.
• Local pool chain-link rule: The local Section 4401 chain-link specification allows at most a two-and-one-quarter-inch square mesh, or slats fastened at the top or bottom reducing openings to at most one and three-quarter inches. This is Raytown’s express local provision: the referenced pool code uses a one-and-three-quarter-inch opening and describes slats secured at both top and bottom. The residential code gives its own locally amended provisions priority in direct conflicts. Pool specifications do not waive the residential-yard chain-link location prohibition.
• Pool clearances: Nonconflicting referenced pool requirements also apply. The 48-inch barrier height must exist around the full perimeter and for three feet horizontally outside it. A 36-inch clear zone separates the exterior barrier from permanent structures or equipment that could be climbed. The pool-side barrier must be at least 20 inches from the water’s edge. The model’s four-inch ground gap over a solid surface does not replace Raytown’s express two-inch local ground-gap rule.
• Mesh pool barriers: A non-chain-link mesh barrier follows manufacturer instructions and has its bottom at most one inch above the deck, installed surface or grade. It cannot lift more than four inches from that surface or allow a four-inch sphere under a panel. Barrier-section attachments are at least 45 inches above grade; deck sleeves are nonconductive, and hinged gates meet the gate rules. Such mesh cannot be installed on top of an onground residential pool.
• Pool gates and latches: Local pool gates meet the barrier construction rules and accommodate a locking device. Pedestrian gates open away from the pool and are self-closing and self-latching; other gates have self-latching devices. A latch release below 54 inches from the gate bottom must be on the pool side at least three inches below the top, with no opening larger than one-half inch within 18 inches of the release. The local measurement is from the gate bottom; the referenced code uses grade for its corresponding threshold. The Building Official resolves an installation where those different origins affect the result.
• Service and multiple pool gates: Unused utility or service gates remain locked. For double or multiple gates, at least one leaf is secured in place and the adjacent leaf is self-latching, with the prescribed one-half-inch opening limit within eighteen inches of the latch release. These requirements are additional to zoning’s lock requirement when a covered pool is unattended.
• Dwelling walls, doors and windows: When a dwelling wall forms part of the barrier, local Section 4401 states a powered ASTM F1346 safety cover or an audible direct-access door/screen alarm listed and labeled to UL 2017, with deactivation switches at least 54 inches above the door threshold. The referenced pool code also addresses operable direct-access windows with sills below 48 inches above the inside finished floor; the alarm must protect the applicable window, door and screen openings and be listed and labeled as a water-hazard entrance alarm.
• Alarm controls and alternative protection: The referenced code measures ordinary alarm controls from the finished floor and has a 48-to-54-inch range for required Accessible, Type A and Type B units. Raytown’s local door-threshold rule remains explicit. Accessibility configurations, differences between threshold and floor height, and a proposed alternative wall-protection arrangement require the Building Official’s exact application; the model wording does not itself waive the local requirement.
• Pool walls and access steps: Where an above-ground pool wall or a barrier on that wall provides protection, steps or ladders must be secured, locked or removed to prevent access, or surrounded by a compliant barrier. Resulting openings must reject a four-inch sphere. For the referenced onground-wall arrangement, the wall rests on grade, reaches at least 48 inches around the full perimeter, meets applicable barrier standards and is allowed by the manufacturer to serve as a barrier. An atop-wall barrier likewise meets the height and barrier standards and follows manufacturer installation instructions.
• Unusual pool-barrier alternatives: Safety-cover-only, shoreline, natural-topography and alternative-wall arrangements require a specific Building Official and Community Development determination against the local barrier and zoning enclosure provisions. The referenced code’s shoreline option requires no public shoreline access and barriers extending at least 18 inches beyond the water’s edge; its natural-topography option requires prevention of direct access and governing-body approval of equivalent protection. These conditional model alternatives do not establish a local exemption from Raytown’s express outdoor-barrier or independent zoning enclosure and locked-gate duties.
• Dangerous-dog orders: After a dangerous-dog finding, the hearing officer may order fenced containment that prevents escape and prevents the dog from reaching its mouth through the fence. An ordered escape-proof kennel under the serious-personal-injury branch must allow normal standing, have length at least 2.5 times the dog’s length, and protect from the elements. Openings or wooden gaps are at most two inches; gates prevent child entry and animal escape, are lockable and stay locked when the dog is confined unattended. Double exterior walls may be ordered. These are case-specific orders, not dimensions for every pet fence.
• Licensed family childcare: For a licensed family childcare home, fencing is required where needed against traffic, water or other hazards. For family childcare homes initially licensed after the effective date of these rules, and separately for new fences at existing licensed facilities, the fence must be at least 42 inches high. Fences must prevent crawling or falling through and entrapment. Swimming and wading pools must be fenced to prevent child access. At family childcare homes initially licensed after the effective date of these rules, the pool fence must be at least 42 inches high with a locked gate; an above-ground pool may instead have that fence around its top with barricaded steps. Ordinary unlicensed homes do not acquire these childcare dimensions merely because children live there.
• Agricultural and animal-use conditions: An agricultural or animal-related fence remains subject to the permitted use and actual site conditions. Neither acreage nor an animal-containment purpose supplies a citywide height or prohibited-material exemption. Current special-use conditions belong to Community Development or Animal Services; captive-animal permit standards do not by themselves authorize keeping that animal locally.
PRIVATE RESTRICTIONS
Recorded covenants, homeowners-association architectural rules, private easements, boundary agreements and fence ownership or maintenance agreements can create obligations separate from government approval. Section 50-7 preserves private instruments alongside zoning. The actual document and applicable Missouri law determine the private requirement; there is no universal private height or material rule for every Raytown property.
Public approval does not determine a boundary, confer title to land or a fence, settle shared costs or authorize interference with another person’s access. Fence age alone does not decide ownership. A fence crossing an easement is not automatically permissible because it includes a gate. Statutory partition-fence duties remain separate from private agreements and city zoning.
REVIEW AND ENFORCEMENT CONTEXT
Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:
• Permit and site review: Required construction, grading, floodplain, historic, design-area and right-of-way approvals; lawful nonconforming replacement and temporary construction fencing.
• Placement and visibility: Yard and frontage limits, vision triangles, utility and drainage easements, pool locations and recorded site conditions.
• Construction and maintenance: Restricted materials, exposed supports, deteriorated fences, pool barriers and gates, seasonal garden fencing, licensed childcare and case-specific animal enclosures.
• Private matters: Covenant enforcement, ownership, boundaries, easement rights and shared costs remain distinct from municipal code enforcement.
USING THIS INFORMATION
This page provides general orientation on how residential fence rules are structured and applied within the City of Raytown, Missouri. Updated November 2026.
In addition to local fence rules, certain Missouri laws apply statewide. See Statewide Fence Laws in Missouri.
It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with the identified municipality, including its actual municipal or county class, charter, adopted program or special district, and each function’s verified territory, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Missouri law. Applicable requirements depend on the property’s actual facts and the respective authority of the identified offices. Private agreements and recorded rights remain separate from government approvals. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern.