FENCE RULES – MARYLAND HEIGHTS (CITY), MISSOURI

OVERVIEW

This page covers residential fences inside the incorporated City of Maryland Heights, Missouri, in St. Louis County. A Maryland Heights mailing address does not establish that a property is inside the city limits.

Maryland Heights requires a free zoning permit for a new, altered or replacement fence, while routine maintenance is exempt. Residential fences are limited to six feet, with an overall installed height of seventy-eight inches measured from finished grade on the property owner’s side. Location matters as much as height: the front façade, street frontage and sight-distance triangles shape the usable fence area. Wood, vinyl, aluminum and steel chain link are recognized materials, but privacy slats, fabric, barbed wire and electric fencing are restricted. Pool enclosures, masonry, retaining walls, drainage, floodplain conditions and certain animal enclosures add their own requirements. Updated November 2026.

Quick questionMaryland Heights answer
Permit or approvalA free zoning permit is required for erection, alteration or replacement. Routine maintenance is exempt. Pool-enclosing fences and masonry or stone fences have separate building-permit requirements.
Typical fence heightResidential fences: 6 feet, with 78 inches overall installed height above finished grade on the subject property’s side. Corner visibility and pool barriers have separate rules.
Placement & property linesEntirely within the subject property. Side and rear yards are allowed; fences generally cannot extend beyond the dwelling’s front façade into the front yard. Corner and double-frontage lots have additional branches. Easements, rights-of-way and drainage remain separate.
Common fence materialsWood: recognized. Vinyl/PVC: vinyl is recognized. Chain-link: steel chain link is recognized, but residential privacy slats and fabric are prohibited. Pool construction and other material approvals remain separate.
Important local conditionsFence rules may be further affected by pool enclosures, corner and driveway visibility, approved development or landscape plans, easements, public rights-of-way, stormwater drainage, mapped floodplain, retaining walls, beekeeping, dangerous-animal enclosures and licensed family childcare.
Official local resourceMaryland Heights fence zoning permits

The table summarizes ordinary rules. The sections below preserve their applicability, exceptions and site-specific branches.

GOVERNANCE

Maryland Heights is a third-class city. The City Council adopts municipal zoning and construction requirements for land within the city. The City Planner and Planning & Zoning administer fence zoning review. The Building Division and Building Commissioner administer the city’s building and pool requirements. The adopted construction framework includes the 2021 International Residential Code for the specified detached one- and two-family dwellings and townhouses not more than three stories with separate means of egress, and the 2021 International Building Code for its other covered buildings and structures. Both have local amendments.

The city also adopts the 2021 International Swimming Pool and Spa Code through its swimming-pool-code article, together with the 2021 International Property Maintenance Code. These are municipal adoptions. The city’s separate incorporation of selected St. Louis County commercial and multifamily mechanical, electrical and plumbing codes does not replace its residential building or pool framework.

The Public Works Director or designee administers work in municipal public rights-of-way. The Building Commissioner or designee is the city’s floodplain administrator. The Metropolitan St. Louis Sewer District and applicable levee or other districts retain their responsibilities for their facilities and rights. A city fence approval does not decide ownership, private easement rights or responsibility for a shared fence.

PERMIT AND APPROVAL REQUIREMENTS

• Ordinary fence permit: The city’s current fence permit instructions provide an online application route. Unless a stated exception applies, all fences erected, altered or replaced require a free zoning permit. Routine maintenance does not require that permit. The application includes a site plan showing the proposed fence in relation to property lines and existing buildings, plus any other documentation the City Planner requires. The city sends review and issuance notices by email. Ordinary fences do not require inspections unless they enclose a pool.

• Separate building approvals: A fence surrounding a swimming pool requires a building permit. A masonry or stone fence or wall also requires a building permit. The adopted residential code’s exemption for fences not over 7 feet concerns that construction-code permit system; it does not waive the city’s zoning permit, residential height limit or specific pool and masonry requirements.

• Building fees and inspections: Residential building permit instructions describe a minimum application fee that is typically $50, with additional charges possible based on construction cost. Required inspections are arranged through the city. These charges are separate from the free ordinary fence zoning permit.

• Other materials and temporary fencing: The Planning Commission may approve materials outside the residential list after considering quality, durability, safety and neighborhood character. An independent commission review of a fence-design waiver or modification carries a $200 nonrefundable fee; an appeal of a commission denial carries a $150 fee. The code lists $650 for an appeal to the Board of Adjustment. The City Planner may waive design requirements for a temporary fence through a zoning permit that sets its design, height, location and duration.

• Existing nonconforming fences: Fences predating enactment of the Zoning Code may remain or be repaired under its nonconformity provisions. Continuing a nonconformity does not authorize further departures. Article 7 restricts enlargement, extension, reconstruction and structural alteration except through its stated paths. A replacement is not automatically routine maintenance.

• Right-of-way acquisition affecting an existing fence: Where a governmental right-of-way acquisition causes a zoning violation, the property or improvement is exempt only to the extent the acquisition created that violation. A later owner-initiated rezoning ends the exemption and subjects the property to the nonconformity rules; a city-initiated rezoning does not end it. The exception does not permit a traffic hazard as determined by the City Engineer or another safety hazard as determined by the Building Commissioner. Such obstructions may be relocated as close as possible inside the new property line.

• Damage to a nonconforming fence: For a nonconforming structure destroyed by circumstances outside the owner’s control to an extent less than 60 percent of replacement value, restoration cannot increase the former nonconformity. It must begin within 6 months and be diligently completed within 2 years. The value calculation excludes the land, site preparation and a foundation adaptable to a conforming use. Destruction beyond the owner’s control exceeding sixty percent, or destruction within the owner’s control to any extent, requires restoration in full conformity. The ordinance does not expressly assign the exactly-sixty-percent case to either branch. A structure declared substandard cannot be restored to continue a nonconforming use when compliance repairs exceed sixty percent of its reconstruction cost. The Board of Adjustment retains the stated authority to grant reconstruction relief.

• Approved plans and special properties: A planned-district ordinance, conditional-use approval, approved site or landscape plan, or recorded subdivision plat can impose conditions on a particular property. Changes to a required screen or an approved fence layout may enter the applicable modification process. Planning & Zoning determines the current submission and landscape-plan requirements for that change. The city’s building-design review is integrated into the applicable site or development-plan review rather than a separate review for every yard fence.

• Mapped floodplain: Construction or other covered development in the city’s mapped A, AE, AO and AH flood-hazard areas requires a separate floodplain development permit. The written, signed application identifies the land, work, use, structure and improvement values, floodway or flood-fringe location, base-flood and proposed elevations, plans and specifications, and other reasonably required information. City floodplain instructions also describe elevation certificates showing the floodplain boundaries, flow path and relationship to structures, base-flood elevation and lowest-floor elevation, together with two sets of sealed engineering plans. Floodway work requires a no-rise certificate under the city’s published instructions.

• Grading and land disturbance: Clearing, excavation and fill generally require a grading permit, an approved grading plan and a stormwater pollution prevention plan, subject to the ordinance’s exceptions. An exception for small grading applies only if drainage patterns do not change and sediment does not reach neighboring property: less than 5 cubic yards on a site of 10,000 square feet or less, or less than 10 cubic yards on a larger site. Other stated exceptions include building-permitted foundation, basement or pool grading; permitted or accessory agricultural or horticultural activity; gardening and similar work at one- or two-family dwellings; right-of-way work covered by its special-use permit; and trench excavation covered by a construction permit. These categories do not make every fence-post excavation “gardening.”

• Larger disturbed sites: A state land-disturbance permit is required where 1 acre or more is disturbed, including a smaller site that is part of a development ultimately disturbing at least one acre. A city stormwater pollution prevention plan is not required for disturbance under one acre unless the director or City Planner requests it, but the common-development exception remains. Where a grading plan is required, it identifies existing and proposed contours at intervals no greater than two feet, elevations, grading and fill quantities, soils and borings, clearing, owner and engineer information, benchmarks, utilities and sewage facilities within fifty feet of the work, flood boundaries, access, schedule, relevant geological features, site address and drainage. Applicable sewer-district requirements and agency approvals remain part of that review.

• Work in a public right-of-way: Excavating, working or placing objects in a public right-of-way requires a written right-of-way use permit from Public Works, including repair or maintenance work. The application states purpose, location, size and expected start and completion, with two sets of plans; ordinarily each excavation has a separate permit. Inspection charges use the ordinance’s $116 per unit or part-unit schedule for the listed types of work. A cash deposit of at least $100 or bond of at least $1,000 is set according to the work and site. These are conditional right-of-way charges, not the ordinary fence-permit fee.

• Right-of-way insurance and emergency work: Permitted right-of-way work generally requires liability coverage throughout the work, the city named as an additional insured, and proof before work starts. The ordinance ties coverage amounts to the current statutory limits and requires the specified insurer qualifications and advance cancellation notice. A residential owner working beside their own residence without using a contractor for excavation is exempt from the insurance requirement; the director may also waive it where restoration work is under $1,000. In an emergency threatening health or safety while the office is closed, excavation may begin under the emergency provision, with notice of the event and location to the director and a permit application on the next open business day.

FENCE PLACEMENT RULES

• Property boundaries: The owner is responsible for locating the fence entirely within the subject property. The zoning fence provisions do not prescribe a separate numerical side- or rear-property-line setback. The actual boundary, public right-of-way and recorded rights remain distinct from the usable fence area.

• Interior lots: A fence may occupy the minimum side and rear yards. It cannot extend beyond the dwelling’s front façade into the front yard, as determined by the City Planner.

• Corner lots: The minimum side and rear yards may contain fencing. A fence cannot extend beyond the dwelling’s front façade into the primary front yard. The City Planner identifies that frontage from the address, dwelling orientation and/or primary entrance. A fence is allowed in the minimum secondary front yard, but a sight-proof fence is prohibited within the sight-distance triangle. The corner visibility height rule also applies.

• Double-frontage lots: A fence may occupy the minimum side yards but cannot extend beyond the dwelling’s front façade into the front yard. Along the rear street frontage it may extend to the right-of-way line as determined by the City Planner from the address, building orientation, primary entrance and/or established street character. This does not authorize construction in the right-of-way.

• Easements and drainage: The fence ordinance grants no right to erect a fence on a public easement. A building permit for a structure on an easement requires express written consent from all parties holding an interest in it. The property owner must ensure a fence does not block or obstruct stormwater flow. Recorded utility, access and drainage rights and maintenance access remain applicable; subdivision-design easement widths are not an automatic fence setback on every lot.

• Flood-hazard locations: Where a floodway has not yet been designated in the specified A or AE areas, the cumulative effect of proposed development together with existing and anticipated development cannot increase the base-flood water surface more than 1 foot anywhere in the community. In a designated regulatory floodway, encroachment requires the stated hydrologic and hydraulic demonstration of no increase in flood levels, unless the community obtains the required conditional federal map and floodway revision approval. Covered development requires anchorage against flotation, collapse and lateral movement, flood-resistant materials and methods minimizing flood damage. AO and AH conditions also require adequate drainage paths around structures on slopes.

• Right-of-way work and restoration: Construction in the public right-of-way requires at least 48 hours’ notice to Public Works before starting and completion within the approved period unless a written extension is granted. The permittee preserves or restores intercepted watercourses, swales, sewers and drains, keeps gutters open, controls runoff and sediment, and protects neighboring property. Damaged or disturbed areas must be restored within 14 calendar days after each phase, and no later than the permitted work period. Debris is collected and removed daily. Excavations, dumpsters and storage units require the prescribed barricades and traffic safeguards; hazardous equipment cannot be left as an unguarded attractive nuisance. Work hours are 7 a.m.–6 p.m. Monday–Friday and 9 a.m.–5 p.m. Saturday, subject to emergencies, authorized extensions or director-required night work.

• Survey markers: Missouri Section 60.355 prohibits knowingly moving, removing, defacing or destroying its protected survey corners, boundary markers, benchmarks and control monuments, except by a registered land surveyor. It provides a class B misdemeanor classification, restoration-cost liability and the affected owner’s reasonable surveying-cost and attorney-fee remedy. Fence approval does not authorize moving a protected marker.

• Fence-post excavation: Missouri’s underground-facility law includes covered hand digging, augering and driving on private property as well as public land. Its limited tillage and temporary-marker exclusions are not a general structural-post exemption. Under Section 319.026, notice is given through the notification center at least 2 but no more than 10 working days before the expected start. The period begins at midnight following receipt and excludes Saturdays, Sundays and legally declared state or federal holidays. The notice service is Missouri 811. Utility location does not establish a property boundary or permission to enter another person’s land.

• Operator responses and unanswered notice: Operators ordinarily provide location information or a no-facilities response within 2 working days, unless an extended start is agreed through the notification center. Work before the scheduled start requires confirmation that all facilities have been located. If an operator fails to respond to a proper original notice, the excavator must give the required second notice before beginning. The operator then has 2 hours to mark or contact the excavator with its marking time; a notice received by 2 p.m. requires marking that working day, and a later notice requires marking by 10 a.m. the next working day. Only failure to mark or contact under that statutory process permits commencement, with careful excavation still required.

• Ticket life and field markings: The notice expires at 11:59 p.m., 21 consecutive calendar days from the work start date. Work may continue within the described area while the notice remains valid and markings remain visible. Failure to begin within the stated ten-working-day period requires a relocate request before beginning. Unusable marks require remarking under the original notice procedure and response time. Excavators must reasonably preserve marks and may bear reasonable remarking costs caused by lack of care or unnecessary repeat requests.

• Care, damage and emergencies: The approximate location ordinarily includes the facility’s width plus 2 feet on each side, with a wider designation for the specified unusual conditions. Before digging, the excavator determines best practices for confirming horizontal and vertical locations; hand or soft digging is used when possible. An incorrectly located or unmarked facility must be reported through the center, with an operator contact or correct-location response within two hours. Damage, dislocation or disturbance, including protective items such as trace wires and encasements, must be reported. Pipeline contact or damage causing a hazardous-liquid or gas release requires an immediate 911 call. Damage cannot be concealed or repaired without the facility owner’s authorization. The narrow emergency temporary-sewer-repair exception follows notification and does not remove reporting duties. Genuine emergency excavation retains reasonable precautions and notice as soon as practical; the operator has the stated two-hour marking or contact duty. State-highway excavation separately requires the commission’s permit, subject to the statute’s railroad-right-of-way exception.

• Division fences: Missouri’s county-dependent partition-fence systems address their own livestock, shared-fence, repair-entry and removal circumstances. A city permit is not a requirement that a neighbor pay half of an ordinary yard fence and does not establish a right to enter adjoining land or remove another person’s fence. The applicable system, use and agreement determine those duties.

FENCE HEIGHT AND VISIBILITY RULES

• Residential height: A residential fence is limited to 6 feet, with an overall installed height of 78 inches above finished grade on the subject property’s side. The overall allowance does not authorize a seventy-eight-inch fence panel or erase frontage and visibility limits.

• Street-intersection visibility: On a corner lot, nothing may be constructed, erected, placed, planted or allowed to grow more than 36 inches above the established grade of the intersecting streets within the sight-distance triangle. The height is measured from the object’s highest point to the top of curb or pavement edge along the projected radial line from the center of the pavement curve through the object. The triangle is bounded by the right-of-way lines and a line connecting points on the property lines 30 feet from their intersection.

• Driveway visibility areas: The code also defines triangles on both sides of a driveway: 10 by 30 feet for a street with a speed limit of 35 mph or less, or 10 by 45 feet for a street with a limit of 40 mph or more. The longer dimension runs along the right-of-way. The thirty-six-inch clause expressly addresses corner lots and intersecting streets; the City Planner determines how the driveway visibility provisions apply to a proposed fence.

• Pool-barrier height and clearances: The adopted pool code generally requires a barrier at least 48 inches high measured on the side facing away from the pool or spa, around the full perimeter and for a horizontal distance of 3 feet outside the barrier. Bottom clearance is no more than 2 inches over nonsolid ground, such as grass or gravel, or 4 inches over a solid surface, such as concrete, measured outside. A barrier mounted on a pool wall has a maximum 4-inch gap above that wall. These minimums coexist with the city’s residential maximum and independent property-maintenance enclosure requirement below.

MATERIAL AND CONSTRUCTION LIMITS

• Recognized residential materials: The Maryland Heights Municipal Code recognizes wood, vinyl, aluminum and steel chain link. Masonry and stone fences or walls require a building permit. Other materials require Planning Commission review and approval based on quality, durability and potential safety or neighborhood-character impacts. The list does not automatically approve every composite, bamboo, fiberglass, salvaged material or other metal product.

• Restricted materials: Residential fence provisions prohibit barbed wire, privacy slats, fabric, hardware cloth and similar materials, electric fences and battery-charged fences. The animal-control provision’s reference to an electronic restraint system is not an approval for an energized residential security fence. Wire or plastic mesh, such as chicken wire, may be used inside the property for gardening or animal deterrence without a fence permit, but is prohibited along the property perimeter.

• Supports, orientation and maintenance: Fences must be built in a workmanlike manner using accepted construction practices. Wood and vinyl need proper posts and supports; chain link cannot support a wood or vinyl fence, or vice versa. The finished side faces outward, with visible supports and structural components facing inward. Owners must maintain fences and remove those that become unsightly or a menace to public safety, health or welfare. The adopted property-maintenance code requires exterior wood other than decay-resistant wood to have paint, another protective covering or treatment against weather and decay. Peeling, flaking and chipped paint must be removed and the surfaces repainted. Metal subject to rust or corrosion requires an inhibiting coating; existing rust or corrosion must be stabilized and coated against recurrence. Oxidation stains must be removed, with an exception for surfaces designed for stabilization by oxidation.

• Retaining walls: The zoning provision measures height by retained fill and requires a building permit for retaining walls over 24 inches, with City Planner and Building Commissioner review. Walls cannot encroach on adjoining property and must use inorganic material such as landscape masonry, concrete, brick or stone. Painting masonry requires the City Planner’s approval. Construction on a utility easement requires the utility holder’s waiver or consent. The residential code’s separate four-foot permit exemption does not waive this city zoning requirement.

• Repairing railroad-tie walls: Treated wood ties may be used for repairs only within the zoning provision’s cumulative 20 percent of the entire wall face limit; once that maximum is reached, the wall must be replaced entirely with inorganic material. The residential-code amendment also restricts repairs exceeding twenty percent of length and/or area. Staff may require an owner-funded report from a Missouri-registered engineer on the wall’s condition and integrity; the Building Commissioner determines whether repair is sufficient or replacement is required. The construction-code description of a wall under forty-eight inches as landscaping does not remove the zoning permit threshold.

• Pool scope and construction fencing: The adopted pool code requires barriers for outdoor pools and spas and indoor swimming pools, subject to its stated alternatives. Its residential classification addresses household-and-guest use, separately from public or commercial use. The zoning ordinance separately requires a building permit for a pool exceeding 2 feet deep, district setbacks for pools requiring that permit and electric-utility-provider approval before issuance. Pools not requiring that permit follow detached-accessory-structure setbacks. These pool setbacks are not ordinary yard-fence setbacks. An in-ground pool or spa site needs construction fencing at least 4 feet high from excavation until the permanent barrier is complete.

• Pool openings and climbability: Barrier openings must reject a 4-inch sphere. Solid surfaces cannot provide handholds or footholds except normal construction tolerances and tooled masonry joints. Where horizontal-member tops are less than 45 inches apart, those members must face the pool or spa, and vertical-member and decorative-cutout gaps cannot exceed 1¾ inches. Where horizontal-member tops are 45 inches or more apart, vertical gaps may be up to 4 inches, but decorative cutouts remain limited to 1¾ inches.

• Chain-link, diagonal and equipment conditions at pools: Pool-barrier chain-link openings cannot exceed 1¾ inches. The model code’s slat-based opening-reduction option does not override Maryland Heights’ residential slat prohibition. Diagonal-member openings also cannot exceed 1¾ inches, and diagonal members cannot be more than 45 degrees from vertical. Equipment on the same lot outside the pool barrier, including pumps, filters and heaters, must be at least 36 inches from the barrier’s outside.

• Proposed mesh pool systems: A mesh system must satisfy the city’s material and location restrictions as well as its technical pool requirements; the garden-mesh exception is not general pool-fence approval. Under the pool code, mesh installed according to its manufacturer’s instructions has a bottom gap no greater than 1 inch, cannot be lifted more than 4 inches from grade or decking, and must reject a four-inch sphere underneath. Section attachments are at least 45 inches above grade; hinged gates meet the gate rules, and deck sleeves are nonconductive. Mesh cannot be installed atop an onground residential pool. The mesh’s inside must be at least 20 inches from the nearest water edge. Proposed material or design substitutions are determined by the City Building Division and Planning & Zoning under their respective approvals.

• Pool gates and latches: Barrier doors and gates must accommodate a locking device. Pedestrian gates open away from the pool or spa, self-close and self-latch. Nonpedestrian utility or service gates stay locked when not in use. A double or multiple gate has at least one leaf secured in place and the adjacent leaf secured with a self-latching device. For residential barriers, an outside-access, non-self-locking latch release is at least 54 inches above the finished floor or ground. For a self-locking system operated by key, electronic opener or integral combination lock, the residential lock operation control and latch release are no more than 54 inches above that surface. If the only release of a private-pool self-latching gate is on the pool side, it is at least 3 inches below the gate top. Openings within 18 inches of an inside latch cannot exceed ½ inch in any dimension.

• A dwelling wall as part of the pool barrier: Where a wall provides direct access through doors, gates or windows, the pool code provides alarm, listed safety-cover and approved-equivalent protection paths. The alarm path includes a listed UL 2017 water-hazard entrance alarm for doors, gates and operable windows with sills below 48 inches above the indoor finished floor. Alarm deactivation controls are at least 54 inches high in dwellings not required to be Accessible, Type A or Type B units; the specified accessible-unit controls are 48–54 inches high. These control-height conditions are part of the alarm system, not freestanding substitutes for protection. The alternatives include a listed ASTM F1346 cover or an approved equivalent means, such as suitable self-closing, self-latching doors. The independent enclosure duty described below remains relevant to a proposed substitution.

• Onground pool-wall barriers: A manufacturer-approved onground pool wall may serve as the barrier when it begins at grade, reaches at least 48 inches around the entire perimeter and meets the applicable barrier requirements. A wall-and-top-barrier system must reach that height, meet those requirements and follow the manufacturer’s installation instructions. Access ladders or steps must be secured, locked or removed to prevent access unless surrounded by a compliant barrier. Openings left by securing, locking or removing them must reject a 4-inch sphere.

• Natural barrier alternatives: The pool code’s shoreline alternative requires no permitted public access along the shore and required barriers extending at least 18 inches beyond the water’s edge. A natural-topography alternative requires governing-body approval and protection equivalent to the specified barrier provisions. These conditions do not create a general exemption for a yard adjoining water or a slope.

• Independent enclosure and maintenance rule: The city’s property-maintenance code requires a complete fence or barrier at least 48 inches above finished ground, measured away from the pool, around private pools, hot tubs and spas containing water more than 24 inches deep. Doors and gates self-close and self-latch. If the self-latch is below 54 inches above the gate bottom, its release must be on the pool side. Gates must positively close and latch when released 6 inches from the gatepost. An existing enclosure cannot be removed, replaced or changed so that it becomes less effective. Pools must be kept clean, sanitary and in good repair. This provision’s ASTM F1346 safety-cover exception applies to spas and hot tubs, not swimming pools generally.

• Pool covers and overlapping requirements: The pool code separately excuses the stated barrier sections where a spa or hot tub has a compliant lockable ASTM F1346 cover, or a swimming pool has a compliant powered cover. That swimming-pool-cover option does not erase the independent property-maintenance enclosure provision. A proposed cover, pool wall or other substitution that changes an existing enclosure is a determination for the City Building Division under the applicable requirements.

• Dangerous-animal enclosures: For an animal declared dangerous and allowed to remain under the city’s hearing determination, the required secure enclosure prevents young-child entry and animal escape, is at least 5 by 10 feet, has secure sides and either a secure top attached to all sides or sides high enough to prevent escape, and is locked by key or combination while occupied. A secured floor or bottom attaches to every side; without one, the sides extend at least 12 inches into the ground. The enclosure provides weather protection and ventilation, is sanitary, and complies with zoning and building rules. A dangerous-animal warning sign with a symbol warning children must be visible and readable from the public road or thoroughfare from which the property is entered. A similar sign is required on the enclosure or fenced yard. This is not the ordinary design standard for every pet fence.

• Beekeeping: On single-family property, hives belong in the rear yard at least 6 feet from property lines. If a hive is less than 50 feet from any property line, the animal ordinance requires a wood or vinyl enclosure at least 6 feet high at the property lines, with a zoning permit for new fencing. The fence-location and frontage provisions still apply; Planning & Zoning determines the layout where the hive-enclosure and frontage conditions meet.

• Agricultural residential property: Apart from the separate chicken rules, farm animals may be kept and restrained on nonurban or single-family residential properties of 3 acres or more. On single-family residential property, such animals are for the owner’s personal use and enjoyment, not commercial purposes. The ordinary fence requirements still apply; acreage alone is not a fence-permit or material exemption. The city separately prohibits keeping wild animals as pets or for the stated display, training or exhibition purposes, subject to its limited transport and institutional, exhibition and commercial-pet-shop exceptions. A state captive-animal permit is not ordinary residential fence permission.

• Licensed family childcare: State rules require outdoor-play fencing where necessary against traffic, water or other hazards. For homes initially licensed after the rule’s stated effective date, and new fences at existing facilities, the fence is at least 42 inches high. Separately, fences prevent crawling or falling through and entrapment. Swimming and wading pools must be fenced against child access; the specified initial-license cohort requires a fence at least forty-two inches high and a locked gate. The rule allows an aboveground pool alternative using a top fence and barricaded steps. Hazardous animals must be securely penned and inaccessible to children. These licensing requirements do not reduce the city’s separately applicable pool or fence requirements.

• Onsite sewage and special facilities: A fence project involving an onsite wastewater system or sewage lagoon must preserve the system’s required protection, operation and access. The applicable City, district and health authority requirements depend on the actual facility and property. A yard-fence approval does not authorize altering that system or establish an acreage exemption. Required landscape screens and district facilities similarly remain subject to their applicable approval and access conditions.

PRIVATE RESTRICTIONS

Recorded covenants, subdivision indentures, homeowners-association architectural rules, private easements and enforceable boundary or maintenance agreements can add obligations beyond government approvals. Section 25-1.10 recognizes more restrictive private instruments but does not obligate the city to enforce them. Their actual wording and applicable Missouri law determine their scope.

A permit does not determine a boundary, confer ownership of a shared fence, allocate its cost or authorize interference with another person’s access. The age or location of an existing fence alone does not establish title. A gate across an easement does not automatically make interference permissible. Private agreements remain separate from the statutory division-fence duties discussed above.

REVIEW AND ENFORCEMENT CONTEXT

Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:

• Permits and plans: New, altered or replacement fences; the distinction between maintenance and replacement; pool and masonry building approvals; and applicable site, landscape, grading, floodplain or right-of-way review.

• Location and visibility: Front-façade limits, corner and double-frontage lots, sight-distance areas, property boundaries, public rights-of-way, easements and stormwater flow.

• Construction and special uses: Height and material compliance, supports and finished-side orientation, deteriorated fences, retaining walls, pool barriers and gates, and the applicable beekeeping, animal-enclosure or licensed-childcare conditions.

• Private matters: Ownership, covenants, private access rights and shared costs remain distinct from municipal permit and code enforcement.

USING THIS INFORMATION

This page provides general orientation on how residential fence rules are structured and applied within the City of Maryland Heights, Missouri. Updated November 2026.

In addition to local fence rules, certain Missouri laws apply statewide. See Statewide Fence Laws in Missouri.

It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with the identified municipality, including its actual municipal or county class, charter, adopted program or special district, and each function’s verified territory, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Missouri law. Applicable requirements depend on the property’s actual facts and the respective authority of the identified offices. Private agreements and recorded rights remain separate from government approvals. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern.