FENCE RULES – CLARKSVILLE (TOWN), INDIANA

OVERVIEW

This page covers single-family residential fence work within the incorporated Town of Clarksville in Clark County, Indiana. Clarksville administers its own municipal zoning and fence-permit requirements through the Town’s Planning & Zoning Department and Building Commissioner.

Clarksville requires a fence permit and regulates front-yard fencing closely. The general framework is a four-foot required-front-yard limit and a six-foot side/rear limit for enclosures covered by that subsection, with a separate four-foot chain-link limit and stated district exceptions. Front-yard fences have restrictions on their purpose, construction and proximity to the front property line. Recorded restrictions, corner visibility, drainage easements, pools, historic districts and special development districts can change the answer. Wood is recognized, vinyl/PVC is not specifically named as an ordinary yard-fence material, and chain-link has express restrictions. Updated October 2026.

Quick questionClarksville answer
Permit or approvalA Town fence permit is required through GovWell. Submit fence specifications and a site map; the currently linked fee schedule lists $25. Easement, historic, floodplain and pool conditions have separate requirements.
Typical fence heightRequired front yard: generally 4 ft. Side/rear enclosures covered by Section 157-70(B): generally 6 ft; chain-link generally 4 ft. Recorded restrictions, district exceptions and pool-barrier rules require separate attention.
Placement & property linesThe general fence section states no numeric side/rear property-line setback. Front-yard fencing is prohibited along the front property line and along side property lines within 2 ft of the front property line. Sight areas, rights-of-way and easements remain separate constraints.
Common fence materialsWood: recognized, with front-yard design restrictions. Vinyl/PVC: not specifically named as an ordinary yard-fence material. Chain-link: expressly regulated; generally limited to 4 ft and prohibited in required front yards except stated district exceptions.
Important local conditionsFence rules may be further affected by corner lots and driveways, recorded covenants, drainage or utility easements, pool-barrier use, local historic districts, South Clarksville Mixed-Use or West Riverfront standards, approved development conditions, floodplain or floodway status, and Indiana 811 excavation requirements.
Official local resourceTown of Clarksville fence application and waiver documents

The table above is for quick reference. Additional fence-rule details appear in the corresponding sections below. Before purchasing materials or beginning construction, read the sections that apply to the property, review the linked official sources, and confirm site-specific questions with Clarksville Planning & Zoning, the Building Commissioner or the responsible office identified for that issue.

GOVERNANCE

The Town Council adopts Clarksville’s local ordinances. The Clarksville Advisory Plan Commission and Planning & Zoning Department administer the municipal zoning system. The Town of Clarksville Zoning Ordinance, particularly Section 157-70, contains the general fence, wall and hedge standards. The Building Commissioner administers building permits and inspections, with fence applications handled through the Town’s GovWell process.

The Clarksville Code of Ordinances supplies additional historic-preservation, public-easement, stormwater, property-maintenance, animal-enclosure and residential-pool provisions. The MS4 Coordinator serves as the Town’s Floodplain Administrator. The Historic Preservation Commission administers applicable Certificates of Appropriateness. The Technical Review Committee and Town Engineer have roles in development, access, drainage and visibility review where those provisions apply.

Indiana’s statewide residential building rules also apply within their scope. The current framework is the 2020 Indiana Residential Code, 675 IAC 14-4.4, incorporating the 2018 International Residential Code with Indiana amendments. The Indiana Department of Homeland Security’s adopted-code information identifies the effective code. State law also governs covered excavation and certain boundary, live-fence, spite-fence and regulated-drain conditions.

Clarksville’s zoning ordinance uses the more restrictive requirement when applicable regulations conflict and preserves valid private agreements. Side- and rear-yard Section 157-70(B) is expressly framed for fences, walls and hedges not regulated by covenants or restrictions recorded with the Clark County Recorder. A property’s recorded restrictions and its applicable public zoning requirements therefore require separate attention.

PERMIT AND APPROVAL REQUIREMENTS

• Town fence permit: The Fence Application Checklist requires an application through GovWell with specifications for the fence and a site map showing property lines and structures. The permit fee must be paid, and installation begins after approval. The currently linked fee schedule, amended April 15, 2025, lists a $25 fence fee.

• Application drawings: Section 157-50 requires a completed application and a site plan drawn to scale unless waived by the Planning Director. The plan shows abutting streets, lot lines and their dimensions, existing buildings and dimensions, the proposed structure or use and dimensions, access, existing and proposed setbacks, and the principal building’s footprint and dimensions.

• Fence proposed in an easement: When Planning & Zoning identifies an easement during fence review, the Fence Waiver Checklist gives the applicant the option of keeping the fence outside it or completing the applicable waiver procedure. That procedure requires execution and notarization of the waiver, recording with the Clark County Recorder, and submission of the recorded document to Planning & Zoning for attachment to the fence permit. Town acceptance and the governing easement’s conditions remain relevant.

• Indiana residential-code administration: Indiana replaced model IRC Section R105 with an additions-and-alterations provision. The model seven-foot fence permit exemption is not an Indiana statewide exemption. Clarksville’s express fence-permit process applies independently.

• Local historic districts: A Certificate of Appropriateness is required before applicable work or permit issuance. Section 33.86 covers noticeable changes to historic buildings and their appurtenances, including fences, and new construction visible from a public way. Within a historic district’s primary area, changes to walls and fences, or their construction along public ways, are expressly covered. Conservation-district and interim-protection provisions have their own scope. The application may require sketches, drawings, photographs and descriptions. The ordinance provides for issuance following approval or if the Commission does not act within 30 days, subject to an extension agreed to by the applicant; a required certificate accompanies the building or demolition permit application.

• Property in a Special Flood Hazard Area: Chapter 153 requires a floodplain development permit before development begins. Its development definition expressly includes erecting walls and fences. Applications cover work wholly within, partly within or in contact with an identified Special Flood Hazard Area and are made to the Floodplain Administrator. Scaled plans identify the work’s nature, location, dimensions and elevations, existing and proposed improvements and grades, drainage features, and other applicable information.

• Floodway work: Section 153.060 requires Indiana Department of Natural Resources approval, or evidence that the project qualifies for a general license or exemption, before the Town acts on covered floodway development. Local approval cannot be less restrictive than the applicable state approval or qualification conditions.

• Larger soil-disturbance projects and permitted developments: Chapter 52 establishes stormwater and erosion-control review for projects disturbing at least one acre and smaller projects within a qualifying larger common plan. Individual lots within permitted projects have their own plan and compliance provisions. Section 52.087 also addresses erosion and post-construction measures for disturbances of at least 10,000 square feet. The applicable plot-plan, drainage and stormwater requirements depend on the project’s scope and existing development approval.

• Pools and other special sites: Residential pool construction or alteration requires the applicable pool permit and plans. Fences on designated historic or archaeological sites, or work disturbing ground to erect, alter or repair a structure within 100 feet of a cemetery, can also fall under Section 150-160’s State Historic Preservation Office documentation requirements. These requirements apply to the specified site conditions.

• Historic and archaeological site submissions: For work covered by Section 150-160, the historic/archaeological application materials include a letter requesting an archaeological record search from an archaeologist approved by the State Historic Preservation Office, a copy of the search and the Office’s response. Required approval documentation precedes the applicable Town permit or development approval.

FENCE PLACEMENT RULES

• Side and rear yards: Section 157-70(B), within its recorded-covenant scope, permits a qualifying fence, wall or hedge enclosure in or along a required side or rear yard if vision clearance is preserved. The general fence section states no separate numeric side- or rear-property-line setback.

• Required front yard: Front-yard fencing is not permitted along the front property line or along side property lines within two feet of the front property line. Front-yard fencing is restricted to the purposes and forms described below. The required front yard depends on the zoning district, street frontage and lot configuration; it is distinct from the legal boundary.

• Corner and multiple-frontage lots: District rules can establish a front yard on more than one street frontage. The R-1 district addresses each qualifying street frontage; the R-2 development table separately identifies a 10-foot corner front yard and its 20-foot or existing-neighborhood front-yard framework. These district yard measurements identify the area in which the front-yard fence rules operate. South Clarksville Mixed-Use and West Riverfront properties have their own frontage and building-type provisions.

• Boundary and permit responsibility: The Town’s fence waiver states that the Town does not inspect the fence’s location or warrant that it lies within the property boundaries or outside easements and rights-of-way. A survey, recorded plat, legal property boundary, public right-of-way and utility or drainage easement are distinct matters. A tax-map line, curb, ditch or existing fence does not establish the private legal boundary.

• Town sewer and stormwater easements: Section 51.014 requires the sanitary-sewer, stormwater and platted easements covered by that section to remain free of encroachments and obstructions to authorized maintenance access. Section 52.043 expressly prohibits trees, shrubs, structures and fences in drainage easements unless accepted by the Town. Drainage facilities established through subdivision approval can occupy perpetual unobstructed easements.

• Stormwater facilities and access: Section 52.073 requires permanent easements for covered stormwater-quality facilities and a 20-foot-wide access easement from a public right-of-way to each facility. The facility’s actual easement and access arrangement governs placement. The fence waiver separately requires fences near drainage easements to preserve stormwater flow.

• Fence-waiver removal conditions: The published waiver permits the Town or other benefited utility or government to require removal under the earlier of three days’ written notice or the governing instrument’s terms, and to remove encroachments without notice in an emergency. It includes landowner release and indemnity provisions for removal, damage and associated claims. Existing and new easement encroachments also have distinct treatment under Section 51.014.

• Regulated drains, where present: IC 36-9-27-33 establishes drainage-board and county-surveyor access rights extending up to 75 feet, measured at right angles from a tiled drain’s centerline or the top edge of each bank of an open drain. Permanent structures require written board consent within the regulated right-of-way. Temporary structures must be removed immediately when the board or county surveyor orders; trees, shrubs and woody vegetation require written consent. For new regulated drains established after September 1, 1984, or urban drains, the board may reduce the corridor to at least 25 feet from an open ditch’s bank or 15 feet from a tiled drain’s centerline; certain platted-subdivision tiled-drain reductions may reach no less than seven feet on each side, subject to the surveyor’s recommendation. The actual regulated-drain corridor is a site-specific condition. Structures over or through an open regulated drain require the surveyor’s approval of plans and specifications under Section 72.

• Residential pool fence location: Under Section 157-120, a fence used to secure a residential pool must remain at least six feet from the pool’s edge. Where a pool occupies an immediately contiguous lot under the same ownership as the dwelling, its surrounding fence may cross the property line between those lots. The pool itself has separate location requirements.

• Floodway and flood-fringe sites: Section 153.060 requires no increase in base-flood levels in a floodway identified on the effective Flood Insurance Rate Map without the prescribed Conditional Letter of Map Revision process; that process cannot authorize an increase affecting a structure. For a DNR-identified floodway not yet shown as such on the effective map, the ordinance defines an adverse effect as an increase of at least 0.15 foot in the regulatory flood elevation under its hydraulic comparison. A compliant flood-fringe project may receive the local permit. Where the floodway or fringe has not been established, upstream drainage greater than one square mile requires DNR review; drainage less than one square mile requires the specified engineering analysis of floodplain limits and the one-percent-annual-chance elevation. A site near an unmapped waterway with upstream drainage greater than one square mile also goes through the specified DNR review. These are floodplain-development conditions for the affected site.

• Qualifying agricultural fences in a floodway: IC 14-28-1-22.5(d) provides a state floodway-permit exception for an agricultural fence as defined in IC 14-8-2-4.5: a structure primarily used to keep animals in or out of an area that does not obstruct the flow of water or debris through a floodway. The definition and state exception have that specific scope. Applicable Town floodplain-development and fence approvals remain separate.

• Indiana 811 before fence-post excavation: Submit an Indiana 811 locate notice before covered digging, augering or other excavation. Notice must be received at least two full working days and no more than ten calendar days before work. A working day is 7 a.m.–6 p.m. Indianapolis time, excluding Saturdays, Sundays and state or national legal holidays. The normal lawful start is no earlier than 7 a.m. on the next working day after two full working days have elapsed following receipt; earlier work requires electronic positive responses from all affected operators confirming marking or no facilities. Check utility responses and markings and affirmatively acknowledge receipt through Indiana 811 before beginning. The notice expires at 11:59 p.m. Indianapolis time twenty days after its receipt date; continued work requires a new notice and the required renewed markings. The statutory hand-tool exception is limited to excavation using only a hand tool, on property owned or controlled by the person performing it, no deeper than twelve inches. Near marked facilities, statutory tolerance-zone and excavation-method requirements also apply.

FENCE HEIGHT AND VISIBILITY RULES

• Side and rear enclosures: For fences, walls and hedges within Section 157-70(B)’s scope, the general maximum is six feet, subject to vision clearance. A higher enclosure requires a separate provision permitting it. Chain-link generally has a four-foot maximum; the ordinance separately provides a six-foot chain-link maximum in B-2, I-1 and I-2 districts.

• Required front yard: A fence, barrier, enclosure, wall or hedge generally cannot exceed four feet, except where another ordinance provision permits it. In B-2, I-1 and I-2 districts, the stated front-yard exception permits chain-link, aluminum, wrought iron or substantially similar fencing up to six feet. The applicable district and use remain relevant to those exceptions.

• Corner and driveway vision clearance: Section 157-70 requires vision clearance at corner lots and unobstructed views at drives, curb cuts and entrances. Division 15 directs “Vision Clearance” to its “Clear Sight Triangle” definition: street-line legs of 15 feet from the intersection, with no view obstruction in the band from four to ten feet above the intersecting streets’ centerline grade. Division 15 also defines a separate “Sight Distance Triangle” using points at least 25 feet along each property line and an obstruction band from four to twelve feet above established grade, with greater distance where needed for prevailing speed and traffic control. The applicable sight area and measurement should be confirmed with Planning & Zoning for the particular corner or access point.

• Development and access-review sight distances: Section 155-100(J) permits the Technical Review Committee to recommend fence and landscape restrictions to preserve stopping sight distance. Table 155-7 lists design distances of 155, 200, 250, 305, 360, 425 and 495 feet for design speeds of 25, 30, 35, 40, 45, 50 and 55 mph respectively. Subdivision Section 152.72(J) recommends corner sight distances of 200 feet for local streets and 300 feet for minor collectors, with Engineer or Technical Committee review of screening fences and landscaping.

• Covered South Clarksville Mixed-Use frontage buffers: Section 70-6.D and Table 70.6-C require a frontage buffer where a vehicular area abuts street right-of-way, excluding alleys. Within that buffer, a fence has a minimum height of three feet and maximum of three and one-half feet. The buffer is at least seven feet from the street-facing property line for parking areas, or from the sidewalk for other covered uses. Fence placement is two feet behind the vehicular-area curb for parking areas, or three feet from the hedge trunk for other covered uses. One gate or opening per street frontage may be no wider than six feet.

• Covered West Riverfront parking screens: Section 110-5.E.3 excludes Traditional and Civic building types from its additional parking-screen requirements. For other covered building types, the screen is at least three feet high at installation; a fence or masonry wall is three to three and one-half feet high. In addition to permitted driveways, one pedestrian gate or opening per street frontage may be up to six feet wide. These are parking-screen standards for the stated building types.

• South Clarksville Mixed-Use sloping residential frontages: Section 70-5.P permits terraced planters and retaining walls to accommodate changes in grade along non-storefront façades. Those retaining walls cannot exceed 30 inches except along a maximum fifteen-foot section of frontage. This is the district’s sloping-façade treatment.

• Applicable landscape plans and special approvals: Approved development plans, planned unit developments, neighborhood guidelines and historic-district requirements can establish additional site-specific conditions. Section 180-20’s landscape provisions apply to the specified nonresidential uses, residential subdivisions and residential developments requiring site-development-plan approval or special exception, subject to existing-approval exceptions. Required landscape sightlines remain clear at corners and driveways.

• Boundary hedges or live fences: IC 32-26-5-1 requires a qualifying hedge or live fence along the dividing line between different owners’ properties to be cut and trimmed at least once each calendar year to no more than five feet high and three feet wide. The chapter supplies a township-trustee complaint and trimming procedure. This applies to the qualifying boundary vegetation.

• Spite fences: IC 32-26-10-1 treats a fence-like structure as a nuisance when it unnecessarily exceeds six feet and is maliciously erected or maintained to annoy the owner or occupant of adjoining property. The malicious-purpose and unnecessary-height conditions are part of that separate nuisance rule.

MATERIAL AND CONSTRUCTION LIMITS

• Wood, vinyl/PVC and chain-link: Division 15 recognizes wood, metal, masonry and other material construction in its fence definition. Wood fencing remains subject to the permitted form and yard rules. Vinyl/PVC is not specifically named as an ordinary yard-fence material. Chain-link is expressly regulated by the separate height and front-yard restrictions described above.

• Required-front-yard forms and purpose: Section 157-70(C) prohibits privacy, shadowbox, panel, chicken-wire, field and chain-link fencing in a required front yard, except where another provision permits it. A front fence may serve as landscaping, but it cannot be intended or used for security, protection, privacy, retaining, screening, confinement, enclosing or creation of a barrier. It must preserve visibility.

• Front-yard pickets and posts: Pickets must be two to four inches wide and spaced one to two inches apart. Fence posts cannot exceed four by four inches.

• Front-yard lawn-rail and split-rail fencing: Maximum height is 48 inches. Two or three rails are permitted; four-rail lawn or split-rail fences are prohibited. Rails cannot exceed six inches in width and posts cannot exceed four by four inches.

• Front-yard crossbuck fencing: Maximum height is 48 inches, with posts no larger than four by four inches. Horizontal rails cannot exceed one and one-half inches by six inches by sixteen feet. Diagonal rails cannot exceed one and one-half inches by six inches by ninety-seven inches.

• Outward-facing finish: The nonstructural face must face outward. The side/rear provision permits the Planning Director to waive that requirement when it provides no benefit to an adjoining owner or the construction is impracticable. The front-yard subsection separately requires the nonstructural face to face outward.

• Dangerous materials and condition: Section 157-70 prohibits spikes, junk, barbed or razor wire, and sharp or similar objects, except that its I-2 district exception allows barbed and razor wire. Fence material cannot resemble or be assembled from junk. Fences cannot be unsafe, dilapidated, deteriorated, decayed or a threat to health or safety. The property-maintenance code also requires fences and walls to remain structurally sound and in good condition, with appropriate weather protection.

• I-1 and I-2 electric-fence provision: Code Section 130.02 separately addresses low-voltage electrical fencing in those industrial zoning districts. Its published limits are a maximum twelve volts, electrical-fence height no greater than eight feet from its lowest electrical point, a completely surrounding nonelectrical fence or wall no higher than six feet, separation of at least six inches at the closest point, and electrical-fence identification at least every sixty feet. The district limitation is part of that provision.

• Temporary construction or public-safety fencing: The general fence standards allow temporary fencing for the construction period or event and require immediate removal when the project or event ends.

• South Clarksville Mixed-Use frontage-buffer materials: The covered buffer permits black, gray or dark-green steel, stone, masonry, or steel combined with masonry columns or a base. Columns may be no wider than two feet six inches, and a masonry base no higher than eighteen inches. Required trees and hedges occupy the street side of the fence. Hedge shrubs are at least 24 inches wide, spaced no more than 36 inches on center and maintained no higher than 48 inches; required large trees occur at least every 40 feet. The buffer’s permitted-use and material limits apply to that defined buffer.

• West Riverfront parking-screen materials: For building types subject to Section 110-5.E.3, nonvegetative screening must match the allowed façade materials and colors specified by the district. Vegetation is placed between the fence or wall and the street. Traditional and Civic building types are excluded from that additional parking-screen provision.

• Local historic districts: Applicable fence and wall work must preserve historic character and compatibility in design, material, texture, color and placement. The Old Town of Clarksville Historic District and McCulloch House Historic District are local designations. Primary-area compatibility criteria include cohesive street enclosure using appropriate appurtenances such as walls, wrought-iron fencing and landscape masses. Ordinary repair and maintenance retain their exception only when they do not conspicuously change the specified design or exterior characteristics. Within the West Riverfront District, its development provisions also call for Historic Preservation Commission review and comments for development within or adjacent to designated or eligible/potential historic sites and districts under that provision’s scope.

• Fences within an applicable landscape approval: Fences and walls are among the improvements permitted in required landscape buffers under Section 180-30. Within the landscape rules’ development scope, structural landscape features are maintained in good condition; expanses of walls, fences or other barriers over 80 feet receive intermittent softening plantings approximately every 40 feet.

• Tree planting under an applicable landscape approval: Section 180-100(F) requires trees to be planted so that, at maturity, tree trunks have at least ten feet of clearance from fences and the other listed features. This is a tree-placement requirement within the landscape regulations’ stated development scope.

• Private residential pools under the Town pool code: Sections 150.200–150.206 define the local pool category using water depth greater than 24 inches and capacity greater than 1,000 gallons, and address permanent and temporary household/guest pools. The published local enclosure provision calls for a fence five to six feet high with a self-locking gate, unless authorized by official Town Council or Board of Zoning Appeals action. It excludes pools constructed or installed before September 1, 2017. “Self-locking” means a gate or door that closes by its own inertia and automatically locks. The local pool subchapter uses the more stringent applicable pool/zoning requirement; Chapter 150 also gives Commission building and fire-safety laws precedence in a conflict. Confirm the approved enclosure method with the Building Commissioner for the pool’s date, design and applicable state requirements.

• Indiana residential-pool access control: Indiana Section R326 defines its residential-pool category to include in-ground or on-ground pools capable of water depth greater than 42 inches, and all pools installed inside a residence regardless of depth, for noncommercial use by no more than two owner families and their guests. R326.27.3 allows a wall or fence at least four feet high surrounding the pool and deck, with self-closing, latching gates and doors capable of being locked; other means at least four feet high deemed impenetrable by the enforcing authority when constructed and surrounding the area when unused; a combination of those means completely surrounding the pool and deck; or a qualifying power safety cover. The self-closing, latching and lockable gate and door conditions apply to the first three alternatives. A qualifying cover continuously connects to the deck to prevent access when closed, opens or retracts only through the specified key, key-and-switch or coded-touchpad operation, is installed with the necessary track and accessories to manufacturer instructions, and bears the required ASTM F1346–91 (2018) identification. The approved pool enclosure remains a separate matter from an ordinary yard fence.

• Qualifying agricultural partition boundaries: IC 32-26-9 requires at least one adjoining parcel to be agricultural land: land zoned or designated agricultural, used for crops or livestock, or reserved for conservation. Section 2 addresses property outside, abutting or adjacent to a town or city’s corporate boundary. Its partition-fence requirement therefore depends on those conditions. Its livestock-containment specifications include a four-foot board/wire or picket fence, a four-and-one-half-foot straight-rail fence or a five-foot worm-rail fence, sufficiently tight and strong for the listed livestock. Written agreements, allocation of responsibility and township-trustee procedures belong to that agricultural boundary framework.

PRIVATE RESTRICTIONS

HOA covenants, private subdivision restrictions, deed restrictions, private architectural-review requirements, recorded private easements, conservation easements and boundary or partition-fence agreements can impose their own height, material, design and placement requirements. Valid private agreements remain separate from Town permits and public approvals.

Section 157-70(B) expressly addresses side- and rear-yard fences, walls and hedges not regulated by recorded covenants or restrictions. Section 10-250 separately preserves valid private covenants and gives effect to greater public restrictions. Review the instruments affecting the property with the applicable fence subsection and permit requirements.

Public subdivision and development conditions, public drainage or utility easements and regulated-drain rights-of-way have their own governmental administration. They are distinct from private HOA or deed restrictions.

REVIEW AND ENFORCEMENT CONTEXT

Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:

• Fence-permit review: Fence specifications, mapped location, required-yard classification, height, construction form, outward-facing finish and recorded easement conditions.

• Visibility and access: Corner and driveway clearance, development sight-distance conditions, public rights-of-way and access to utility or drainage infrastructure.

• Easement and drainage compliance: Unauthorized encroachments, obstruction of stormwater flow or maintenance access, recorded waiver conditions and regulated-drain approvals where applicable.

• Historic and special-district review: Required Certificates of Appropriateness, compatible fence or wall work, and applicable South Clarksville Mixed-Use, West Riverfront or approved development conditions.

• Pool and environmental conditions: Approved pool access control, fence-to-pool separation, floodplain or floodway development, and applicable larger-project stormwater or erosion measures.

• Condition and excavation: Unsafe or deteriorated fencing, dangerous materials and compliance with Indiana 811 notice, positive-response and excavation requirements.

USING THIS INFORMATION

This page provides general orientation on how residential fence rules are structured and applied within the Town of Clarksville, Indiana. Updated October 2026.

In addition to local fence rules, certain Indiana laws apply statewide. See Statewide Fence Laws in Indiana.

It is not legal advice and does not replace official ordinances, permits, certificates, improvement-location approvals, development approvals, applicable building-code requirements, surveys, or professional guidance. Rules and interpretations may change, and application may vary based on zoning district, plan-commission jurisdiction, county zoning coverage, site conditions, subdivision/land-development status, easements, rights-of-way, floodplain or floodway status, stream conditions, stormwater or drainage requirements, regulated-drain conditions, road or highway conditions, INDOT jurisdiction, historic/design/special-district status, rural or agricultural context, livestock, lawful-fence or agricultural partition-fence context, live-fence or spite-fence conditions, local permit administration, pool-barrier use, Indiana 811 utility-excavation requirements, and private restrictions such as HOA covenants, deed restrictions, private agreements, recorded partition-fence agreements, or conservation easements. Before purchasing materials or beginning construction, confirm current requirements and site-specific limitations with Clarksville Planning & Zoning, the Building Commissioner, and any applicable private agreements. If this page conflicts with official ordinances, published guidance, adopted district guidelines, or direction from Clarksville Planning & Zoning or the Building Commissioner, the official sources control. For legal advice or legal interpretation, consult a licensed attorney.