FENCE RULES – MADISON (CITY), INDIANA

OVERVIEW

This page applies to residential fence work within the municipal boundaries of the City of Madison, Jefferson County, Indiana. Madison administers zoning through its advisory Plan Commission and the City’s Unified Development Ordinance.

Madison’s March 2026 Unified Development Ordinance exempts residential fences, walls, and retaining walls from its building-permit requirement while regulating their location, height, materials, and visibility. Ordinary fences may reach 4 feet in front yards and 6 feet in side and rear yards, with a general 5-foot separation from public rights-of-way. Historic-district fences follow a separate approval and design framework, including lower limits in publicly visible areas. Wood, vinyl/PVC, and chain-link have different significance for opaque screening and historic design. Easements, corner lots, required development buffers, hillside excavation, floodplains, pools, and Indiana utility-location requirements can change the project’s requirements. Updated November 2026.

Quick questionMadison answer
Permit or approvalThe UDO expressly exempts residential fences, walls, and retaining walls from its building permit. Historic Certificates of Appropriateness, easement permissions, floodplain permits, and applicable hillside or construction-stormwater approvals remain separate.
Typical fence heightOrdinary rule: 4 feet in front yards; 6 feet in side and rear yards. Historic guidelines use 3 feet in front yards and other areas of primary visual concern, with up to 6 feet in rear areas not readily visible publicly. Other required-barrier and approved historic exceptions apply.
Placement & property linesGenerally 5 feet from a public right-of-way, subject to the lower-front-setback exception. A fence may be on a property line that does not abut a public right-of-way with adjoining-owner written approval, or up to that line without the agreement. Easement approvals and sight-triangle restrictions apply.
Common fence materialsWood: recognized for opaque fencing; wood pickets are appropriate for visible historic locations. Vinyl/PVC: vinyl is recognized in the opaque-fence definition and solid PVC/vinyl in dumpster screening; historic public-view restrictions apply. Chain-link: chain-link with slats does not qualify as solid fencing, and chain-link is inappropriate in publicly visible historic locations.
Important local conditionsFence rules may be further affected by historic-district approval, multiple street frontages, site-specific sight triangles, development screening requirements, planned unit development standards, easements and regulated drains, hillside site work, floodplain or floodway location, pool barriers, qualifying agricultural boundaries, and fence-post excavation.
Official local resourceCity of Madison Building and Design information and applications

The table above is for quick reference. Additional fence-rule details appear in the corresponding sections below. Before purchasing materials or beginning construction, read the sections that apply to the property, review the linked official sources, and confirm site-specific questions with the City of Madison Planning, Preservation and Design Department or the responsible office identified for the issue.

GOVERNANCE

Madison’s residential fence requirements are distributed among the City of Madison Unified Development Ordinance, general ordinances, historic guidelines, permit materials, and applicable Indiana laws. The UDO was adopted March 17, 2026 and combines zoning and subdivision regulations.

• Local adoption and administration: The Common Council adopts the City’s development rules. The Planning, Preservation and Design Department supports the advisory Plan Commission and Board of Zoning Appeals. The UDO Administrator administers and enforces the ordinance, and works with the Building Inspector on building permits and inspections. The Board of Zoning Appeals handles development-standard variances and appeals within its authority.

• Historic district: The Madison Historic District Board of Review and preservation staff administer historic review. The district generally encompasses downtown from the toe of the hill to the Ohio River and between the eastern and western city limits; the official district map controls a particular property’s inclusion.

• Floodplain and stormwater: The City’s Floodplain Management and Stormwater Management functions administer flood-hazard and stormwater requirements. Current City guidance identifies the Code Enforcement Officer/MS4 Coordinator as the floodplain administrator. MS4 means Municipal Separate Storm Sewer System.

• Roads, utilities, and drains: The Board of Works approves site-specific sight triangles and relevant public-way matters. City utilities administer access to their equipment and facilities. Where a statutory regulated drain affects a property, the county surveyor and drainage board administer the applicable drainage rights and consent requirements. Work affecting a state highway right-of-way may also involve the Indiana Department of Transportation (INDOT).

• Indiana residential code: The currently effective statewide residential code is the 2020 Indiana Residential Code, 675 Indiana Administrative Code (IAC) 14-4.4, based on the 2018 International Residential Code with Indiana amendments. Indiana replaced model Section R105. The state residential code does not supply a seven-foot fence building-permit exemption; Madison’s express residential-fence exemption comes from its UDO.

PERMIT AND APPROVAL REQUIREMENTS

• Residential building-permit exemption: UDO Section 7.10.G.1.h exempts the erection, construction, installation, moving, addition, or alteration of residential fences, walls, and retaining walls from the UDO building permit. Exempt work must still comply with applicable UDO requirements. The residential-fence exemption has no stated height threshold.

• Historic Certificate of Appropriateness: Exterior fence and wall changes visible from public streets or alleys within the Madison Historic District require a Certificate of Appropriateness (COA). The Historic District Review Board’s official resources provide the guidelines, map, application, and fence/wall addendum. The posted application identifies fences and walls for staff review. Staff may refer uncertain requests to the Board, and a staff denial may be appealed to the Board.

• Historic fence application documents: Submit the COA application, a detailed description of the work, photographs of existing conditions with captions, sketches or photographs of the proposal, samples or brochures, and the fence/wall addendum. The addendum requests fence height, length, materials, gate count and materials, and installation method, such as in-ground posts, concrete-set posts, or a plinth. An applicant acting for the owner must provide owner authorization.

• Historic fees and Board hearings: The posted application lists a $10 staff-review fee. For applications heard by the Board, it lists a $25 application fee, $15 advertising fee, and $2 sign fee per street. Board applications must be filed at least 15 days before the scheduled meeting, subject to published deadlines. Applicants or representatives must attend the hearing; notification signs must be posted for 15 consecutive days immediately before the hearing. Work may begin after the required COA has been issued and other applicable approvals are satisfied.

• Historic maintenance: Ordinary maintenance and repair that do not alter exterior appearance, and qualifying in-kind replacement using the same materials, shape, size, and design consistent with historic design standards, do not require a COA. Changes beyond an approved COA’s scope require further approval.

• Hillside site work: In the Hillside (HS) District, a hillside permit is required before site or land alteration, including adding, removing, or shifting dirt, clearing, changing elevations or contours, or constructing a driveway. Fence work involving such site disturbance is subject to that approval. The July 2026 application calls for a site plan at 1 inch = 50 feet, with 5-foot topographic intervals, existing utilities, and proposed landscaping. It also requests certified soil borings/site analysis and professional construction drawings where applicable. Certified notices to adjoining owners, including owners across streets, alleys, easements, and corners, must be mailed at least 10 days before the meeting; receipts and returned cards are due at least one working day before the meeting.

• Floodplain development: Chapter 156 expressly includes erection of walls and fences in “development.” A floodplain development permit is required before development in a Special Flood Hazard Area. The City’s floodplain and stormwater resources provide the ordinance and application. Required information includes the project description and legal location, a site plan showing existing and proposed development and grades, and applicable dimensions, elevations, drainage, and watercourse changes. Floodway projects also require applicable Indiana Department of Natural Resources (DNR) authorization.

• Construction stormwater: Applicable Construction Stormwater General Permit coverage is required before construction-related disturbance of one acre or more, including smaller disturbances that are part of a larger common plan of development or sale meeting that threshold. A stand-alone project disturbing less than one acre and outside a larger common plan does not require that coverage. Under Indiana Code (IC) 36-1-3-14, effective May 1, 2025, local construction-stormwater requirements cannot exceed those of the Indiana Department of Environmental Management (IDEM). IDEM’s construction-stormwater guidance explains the controlling limits on local requirements. Sediment, dust, drainage, and illicit-discharge duties remain applicable within their respective scopes.

• Residential lots within an active permitted development: An individual residential lot operator may work under the overall developer’s stormwater permit when the state conditions are met, including the residential development registration and a lot-specific stormwater pollution prevention plan, or an applicable lot plan included in the overall plan. State guidance does not require separate submission of that lot plan or a separate Notice of Intent while the operator properly works under the overall permit; IDEM may require separate coverage for noncompliance.

• Easements and regulated drains: Fence or wall placement in an easement requires the easement holder’s approval. Municipal drainage-easement work is also subject to City acceptance where required. A permanent structure within a statutory regulated-drain right-of-way requires the drainage board’s written consent. These permissions are separate from the residential building-permit exemption.

• Site-specific development approvals: An applicable planned unit development (PUD) ordinance, recorded public development commitment, required development-screening plan, or approved subdivision plat can establish additional conditions. Screening plans are submitted with required development-plan review or before a required building permit, whichever occurs first. The City’s approval of a fence project does not replace applicable state authorization or private permissions.

FENCE PLACEMENT RULES

• Public right-of-way separation: Under UDO Section 4.8.G, an ordinary fence or wall must be at least 5 feet from any public right-of-way. If the zoning district allows a front-yard setback below five feet, the fence may be at that minimum setback. Approved historic-district fences have the separate treatment described below.

• Property lines away from public rights-of-way: A fence or wall may be placed on the property line with written approval from adjoining owner(s), except where the line abuts a public right-of-way. Without that agreement, it may be placed up to the property line. The ordinance specifies no additional numeric interior offset for that situation.

• Required yards: Fences are expressly permitted within minimum front, side, and rear yard setbacks under Section 4.8.E.3. Fences are also excluded from the accessory-structure footprint calculation. Fence-specific right-of-way, visibility, easement, height, and material standards still apply.

• Legal boundaries: A property line, public right-of-way, and easement boundary are distinct. A tax map, curb, pavement edge, ditch, hedge, or existing fence is not a determination of the legal boundary. Recorded plats, easements, and appropriate boundary information matter when locating a fence.

• Sight triangles and hazards: Fences and walls cannot create traffic hazards, occupy sight triangles, or be hazardous or dangerous to people or animals. Sight-triangle dimensions depend on the location’s speed, topography, and sight distance; a Professional Engineer or Professional Land Surveyor determines them for approval by the Board of Works.

• Easements and watercourses: Fences and walls cannot occupy drainage, access, utility, or other easements without approval from the holder(s). The stormwater ordinance requires City acceptance for fences in drainage easements within its scope. Property owners or lessees must keep watercourses free of trash, debris, and obstacles that pollute, contaminate, or significantly retard flow, and maintain private structures so they do not threaten the watercourse. City ordinances also prohibit obstruction of a drain’s natural course or natural water flow.

• Hydrants and utility equipment: A fence or post cannot obscure or hinder immediate access to a fire hydrant, fire-department connection, or fire-protection control valve. Maintain 3 feet of clear space around a hydrant’s circumference, unless otherwise required or approved by the Fire Chief. Water-meter access must also remain unobstructed.

• Public development conditions: In a PUD, the approved PUD ordinance governs site standards; an unspecified standard follows the most similar zoning district and/or UDO site standard as determined by the Administrator. Recorded public plats, development commitments, public drainage/utility easements, and statutory regulated-drain rights are administered under the applicable public framework. They remain distinct from privately enforced association or deed covenants.

• Subdivision no-access easements: Section 6.12.D.3 provides 25-foot no-access easements along railroads and limited-access highways, and 5-foot no-access easements along specified existing perimeter roads where lots can use an internal subdivision road. The operative provision excepts fences from its structure prohibition, while its suggested plat wording broadly prohibits structures. Actual recorded plat terms and the separate easement-approval requirement remain material to placement.

• Pedestrian easements: A subdivision next to a park, school, or other public community facility may be required to provide a perpetual unobstructed pedestrian easement at least 20 feet wide. Structures cannot be placed in such an easement where they limit or impede accessibility under the Americans with Disabilities Act (ADA).

• Statutory regulated-drain corridors: Where IC 36-9-27 applies, drainage officials have entry rights within 75 feet, measured at right angles from a tiled drain’s centerline or the top edge of each bank of an open drain, as determined by the surveyor. For qualifying new drains established after September 1, 1984 and urban drains, the board may reduce the corridor to no less than 25 feet from each open bank or 15 feet from a tiled centerline. In a platted subdivision, a further tiled-drain reduction requires the surveyor’s recommendation and cannot be below 7 feet on each side or the recommended width. These are authorized reductions requiring the applicable determination. Permanent structures require written board consent; temporary structures must be removed immediately when ordered. Trees, shrubs, and woody vegetation require written consent and may be removed for drainage work.

• Floodway property: Nonexempt floodway obstructions and construction require applicable DNR authorization before work. A qualifying agricultural fence primarily used to keep animals in or out is exempt from the state floodway construction permit when it does not obstruct water or debris flow and satisfies applicable standards. Local floodplain and easement requirements remain separate.

• Pool siting and opaque screening: The UDO defines a swimming pool for its local rules as a self-contained recreational body of water at least 24 inches deep. Pools must be in the rear yard. Their minimum side and rear setbacks are 10 feet without opaque fencing along the abutting property line, or 5 feet with that screening, with a greater district minimum controlling. Those distances govern the pool’s location. State residential-pool access control has the separate scope described under Material and Construction Limits.

• Newly enclosed land using an existing neighbor fence: Under IC 32-26-2-15 through -18, when enclosure of previously unenclosed property makes an existing fence a partition fence, the person enclosing the property must pay the existing fence owner 50% of its value as estimated by that owner, subject to the statutory recovery process. Joining the new fence to the neighbor’s existing fence requires that owner’s consent. Without consent, the statute provides for each owner to contribute half a lane’s width, or a reasonable distance, for the second fence. A person ceasing to use the property or opening the enclosure must give interested persons six months’ notice before removing the fence portion forming a partition with another enclosure.

• Fence mistakenly erected on another property: IC 32-26-2-19 and -20 address removal within six months after determination of the legal property line, conditioned on paying or offering reasonable compensation for injury caused by entry. Where removal would expose a crop, the crop must first be gathered or secured, or have had a reasonable opportunity to be gathered and secured; that protection may extend the removal period.

• Qualifying agricultural boundary at the municipal edge: IC 32-26-9 requires at least one adjoining parcel to be agricultural land—zoned/designated agricultural, used for crops or livestock, or reserved for conservation—and includes property outside, abutting, or adjacent to municipal boundaries. Where its partition-fence duty applies, the fence is constructed on the dividing line. If no division has been made, for a north–south line the east owner builds the north half and west owner the south half; for an east–west line the north owner builds the west half and south owner the east half. An owner who has maintained a different half for at least five years may continue maintaining it. An interested owner who has built, rebuilt, or repaired that owner’s portion gives a defaulting owner or agent/tenant 20 days’ notice to complete the defaulting portion. Continued default is reported to the township trustee, who estimates and gives notice of probable cost; if the work remains undone 20 days after that notice, the trustee performs it using materials most commonly used by local farmers. Statutory procedures address cost recovery and watercourse-related allocation disputes.

• Indiana 811 before post-hole digging: Submit an Indiana 811 locate notice before covered fence-post excavation. Notice must be received at least two full working days and no more than ten calendar days before work. A working day is 7 a.m.–6 p.m. Indianapolis time, excluding Saturdays, Sundays, and state/national legal holidays. The normal start is no earlier than 7 a.m. on the next working day after two full working days have elapsed following receipt. An earlier start requires all affected operators’ electronic positive responses confirming marked facilities or no affected facilities. Check responses and markings and affirmatively acknowledge receipt of the required operator information to Indiana 811 before starting. A notice expires at 11:59 p.m. Indianapolis time 20 days after its receipt date; unfinished covered work requires a new request and new affected-operator markings before continuing. The narrow hand-tool exception requires work solely by hand tool, on property owned or controlled by the person digging, to a depth no greater than 12 inches.

FENCE HEIGHT AND VISIBILITY RULES

• Ordinary yard limits: The UDO’s Fence and Wall Height table sets a 4-foot front-yard maximum and a 6-foot side/rear-yard maximum in all districts. Height is measured from the ground adjacent to the fence to its top. Where topography necessitates, average site elevation may be used. A greater height is available where required by another UDO provision or applicable local, state, or federal law.

• Corner and through lots: A front lot line includes a property line separating the lot from a street. Corner lots have two front-yard setbacks and two side-yard setbacks. A through lot fronts on two parallel streets or streets that do not intersect at the parcel. Apply the actual street frontage and yard classification to the fence, together with sight-triangle protection.

• Intersection visibility: The UDO prohibits encroachment into a sight triangle. Its dimensions are determined for the particular site by a Professional Engineer or Professional Land Surveyor and approved by the Board of Works. The ordinance supplies no single citywide numeric triangle dimension for every intersection.

• Retaining walls and approved historic fences: Section 4.8.G exempts retaining walls whose purpose is structural support for grading/elevation changes, and Historic District fences approved by the Board of Review, from that section’s standards.

• Historic-district height and transitions: Guideline 20.6 limits fences to 3 feet in front yards and other areas of primary visual concern. Fences in rear yards and other areas not readily seen publicly may be up to 6 feet. The transition from low front fencing to higher rear fencing should be as far to the rear of the enclosed structure or yard as possible, and no more than half the yard depth forward of the principal structure. Tall hedges that obscure the property from the street are discouraged.

• Boundary hedges and live fences: IC 32-26-5 requires a hedge or other live fence grown along a dividing line between different owners to be cut and trimmed at least once each calendar year to no more than 5 feet high and 3 feet wide. On a qualifying written adjoining-owner complaint, the township trustee examines it within five days; required notice provides 30 days to trim and remove brush to the owner’s property before statutory enforcement.

• Malicious taller boundary fences: Under IC 32-26-10, a fence-like structure unnecessarily exceeding 6 feet and maliciously erected or maintained to annoy adjoining owners or occupants is a nuisance. The statute provides nuisance remedies for an injured adjoining owner or occupant.

MATERIAL AND CONSTRUCTION LIMITS

• Ordinary materials and orientation: The UDO recognizes wood and vinyl as examples of substantial materials for an opaque fence. Its opaque-fence definition expressly states that chain-link with slat inserts and shadowbox fencing are not solid fences. Solid PVC/vinyl is expressly listed for dumpster screening. Structural supports for nonagricultural fences must face inward.

• Ordinary UDO fence materials: For fences governed by Section 4.8.G, razor wire, barbed wire, sharpened top spikes, and electrified fences are prohibited except for agricultural, industrial, correctional-facility, or utility purposes. Underground pet-fence systems are excluded from the electric-fence prohibition. Materials not traditionally used for fences, including pallets, are prohibited. Fences and walls governed by that section must avoid danger to people and animals.

• Visible historic fences: Guideline 20.5 identifies wood pickets and metal designs as appropriate along front or readily visible side property lines. Wire, chain-link, and vinyl are inappropriate there. Guideline 20.9 identifies plastic, vinyl, chain-link, and wire as inappropriate in public view; these materials may be appropriate in rear or side yards not visible publicly. Where chain-link is introduced in an appropriate location, dark-green or black vinyl coating is recommended, with plantings such as ivy or vines to screen metal fencing.

• Historic preservation and replacement: Retain, preserve, and maintain historic cast-iron fences and walls. Repair using the applicable wood, metal, or masonry standards. Necessary replacement is in kind, matching composition, size, shape, color, pattern, and texture. New fences must be compatible with the associated building, site, and streetscape in height, proportion, scale, texture, material, and design. False historical details or non-original architectural embellishments on existing fences are inappropriate.

• Historic material repairs: Historic masonry should be repaired rather than replaced, cleaned only with low-pressure water and appropriate mild detergents, and repointed with compatible mortar; sandblasting and abrasive cleaning are prohibited. Replacement masonry should match the historic bonding pattern and original units’ size, color, and texture; deteriorated mortar joints are removed with hand tools under a skilled mason. Water-repellent sealers are generally inappropriate, and historically unpainted masonry should remain unpainted. Historic concrete and stucco are retained and repaired with compatible material, strength, composition, texture, and color, using gentle cleaning. Historic stucco is not removed from masonry unless more than 50% has lost its bond to the backing. Wood repairs favor preservation methods such as splicing, patching, or suitable epoxies; necessary replacement matches the original. Historic metal repair uses in-kind material or appropriate metal epoxies, with replacement elements matching the original.

• Historic retaining walls: Preserve historic retaining walls. New retaining walls are appropriate where a distinct grade change exists and should be brick, stone, or concrete block covered with stucco.

• When development requires buffers: Section 4.6 screening and bufferyard standards apply to a new primary structure or new use on a vacant parcel. Changes in use or exterior alterations to a primary structure require compliance to the greatest extent possible given existing site conditions. Required buffers are measured inward from the property line, apply to side and rear yards, and may overlap required setbacks without reducing those setbacks. Where adjoining property is a PUD or outside Madison’s jurisdiction, the Administrator selects the most comparable district. Similar surrounding uses may support a reduction or omission, documented by the Administrator in writing.

• District labels for development buffers: The table uses Agricultural (AG), Residential Agricultural (RA), Hillside (HS), Open Space (OS), Low Density Residential (R1), Medium Density Residential (R2), High Density Residential (R3), Historic District Residential (HDR), Riverfront (RF), Local Business (LB), General Business (GB), Central Business (CBD), Aviation Business (AB), Light Industrial (I1), and Heavy Industrial (I2). A planned unit development is a PUD.

• R1 and R2 development buffers: Beside LB or GB property, Table 3 provides a 20-foot buffer or a zero-foot buffer with Type A plantings or a fence/wall. Beside I1 or I2, it provides a 40-foot buffer or a 20-foot buffer with Type B plantings or a fence/wall. The table lists no requirement beside AG, RA, HS, OS, R1, R2, R3, HDR, CBD, and RF. Its AB entries have the conflict described below.

• R3 development buffers: Beside AG, RA, HS, OS, R1, or R2, Table 3 provides a 20-foot buffer or a zero-foot buffer with Type B plantings or a fence/wall. Beside LB, GB, I1, or I2, it provides a 20-foot buffer or a zero-foot buffer with Type A plantings or a fence/wall. It lists no requirement beside R3, HDR, CBD, or RF. Its AB entries have the conflict described below.

• Residential development in other districts: Table 3 lists no buffer for AG, RA, HS, and OS parcels. For CBD, RF, and HDR parcels, it lists no buffer except that a multifamily dwelling adjacent to a single- or two-family dwelling requires Type C plantings. Where residential development is permitted in LB or GB, a parcel beside AG, RA, HS, R1, or R2 requires a 40-foot buffer with Type C plantings or a fence/wall; beside I1/I2, a 20-foot buffer with Type A plantings or a fence/wall; beside R3, HDR, LB, GB, CBD, RF, or AB, none. These requirements apply when the development meets Section 4.6’s compliance thresholds.

• Aviation Business screening-table conflict: For R1/R2 or R3 property adjoining Aviation Business (AB) property, Table 3 places that adjacency in both no-buffer and buffer-required categories. The applicable requirement for those adjacencies needs an administrative determination; the table does not give one consistent result.

• Required screening construction: A fence or wall used to satisfy Section 4.6 must be opaque and at least 6 feet high, within the side or rear bufferyard. A compliant barrier already installed by the adjoining owner satisfies the corresponding segment. A screening berm must peak at least 5 feet high, with a maximum 3:1 slope contained in the buffer. A bufferyard may contain drainage/utility features, but its planting, fence, wall, or berm cannot be in the easement.

• Required screening plantings: Per 100 linear feet of property line, including driveways, Type A requires 2 shade trees, 4 evergreen trees, and 6 shrubs; Type B, 6 shade trees, 10 evergreens, and 12 shrubs; and Type C, 8 shade trees, 12 evergreens, and 18 shrubs.

• Parking-area screening: Where Section 4.5 applies to a new or changed parking area, a parking area other than a drive within 500 feet of a residential zoning district must be screened by continuous evergreen vegetation, a 6-foot opaque fence/wall, or a 6-foot earthen berm. Compliance triggers include a new primary structure or use on a vacant parcel, a change of land use, moving/altering/changing at least 50% of existing parking or loading areas, or increasing parking spaces by at least 50%. Regular maintenance is excluded.

• Dumpster and trash-collection screening: Where Section 4.8.F applies to a dumpster or trash-collection area, provide permanent opaque wooden, brick, solid PVC/vinyl, or masonry fencing on all sides so the receptacles are invisible from public rights-of-way and adjoining parcels year-round. One side must be gated and remain closed except during access. Such dumpsters are not permitted in R1/R2 districts. Temporary construction/demolition dumpsters do not require screening, but remain subject to applicable location standards and may be on site no more than one week before and one week after the associated work.

• State residential-pool scope: Indiana Section R326 applies to a residential in-ground or on-ground pool capable of water depth greater than 42 inches, and to all pools inside a residence regardless of depth, intended for noncommercial use by no more than two owner families and their guests. Artificial lakes are excluded from the swimming-pool definition.

• State residential-pool access alternatives: R326.27.3 permits: (1) walls or fencing at least 4 feet high completely surrounding the pool and deck, with self-closing, latching gates and doors capable of being locked; (2) other means at least 4 feet high, deemed impenetrable by the enforcing authority at construction, surrounding the pool and deck when unused; (3) a combination of those methods, with the stated self-closing, latching, lockable gate/door conditions; or (4) a qualifying power safety cover. The gate/door condition applies to the first three methods.

• Qualifying power safety cover: The cover must connect continuously to the deck to prohibit access when closed, operate mechanically with a key, key-and-switch, or personal-code touch pad, and have required tracks, rollers, rails, guides, and accessories installed to manufacturer instructions. Its identification tag must show compliance with ASTM F 1346-91 (2018) for power safety covers.

• Qualifying agricultural partition-fence construction: Where IC 32-26-9 applies, the fence must be sufficiently tight and strong to hold cattle, hogs, horses, mules, and sheep. Recognized types are a 4-foot straight board-and-wire, straight wire, straight board, or picket fence; a 4½-foot straight rail fence; or a 5-foot worm rail fence. Owners bear their statutory proportional construction and repair costs.

• Qualifying agricultural partition fences at watercourses: If a ditch or creek forms, covers, or marks the dividing line so that the required fence cannot be built and maintained on that line, each owner must build a separate fence on that owner’s property as near the boundary as practical and maintain it at that owner’s cost. Where a required partition fence crosses a ditch or creek and a stationary crossing is impracticable, a floodgate or similar structure must be sufficiently high, tight, and strong to turn hogs, sheep, cattle, mules, horses, or other domestic animals, swing up in high water, and connect continuously with the partition fences.

• Qualifying agricultural watercourse allocation disputes: If a ditch or creek crosses the division line and adds expense to maintaining the part over the stream, and the owners cannot agree on their proportionate shares, the township trustee appoints three disinterested citizens to apportion the partition fence each owner must build. If constructing and maintaining a required floodgate or similar crossing causes additional expense and the owners disagree about its character or their cost shares, either owner may give the trustee written notice describing the disagreement and its nature. The trustee then appoints three disinterested citizens of the township to determine the kind of structure and apportion its cost, considering the portions of fence maintained by each owner. A trustee related to an interested owner, or personally interested as an owner, is replaced by the trustee of another township who resides nearest the fence.

• Qualifying agricultural watercourse determinations and default: A majority determination by the arbitrators on matters submitted under IC 32-26-9-3 is final and binding on each owner. The statute provides compensation of $2 per arbitrator, paid by the owners in the proportions ordered for the gate or structure. If either or both owners fail to construct or pay for the determined gate or structure in their ordered proportions within 30 days after the determination, the township trustee must proceed at once to construct it and collect the cost, including arbitrator compensation, from the defaulting owner under the ordinary partition-fence cost-recovery procedure. The gate or structure must subsequently be repaired, rebuilt, or replaced according to the arbitrators’ determination.

• Guard- or sentry-dog training kennels: City Section 91.19 requires runs completely surrounded by fencing at least 8 feet high, with anti-climbers or a completely covered top, and an 8-foot perimeter fence with anti-climbers around the training and kennel area. Gates and entrances must be locked when unused, and fences maintained escape-proof. This applies to the specified training-kennel activity.

PRIVATE RESTRICTIONS

Homeowners’ association (HOA) covenants, private subdivision restrictions, deed restrictions, architectural-review agreements, conservation easements, private access or utility easements, and private boundary agreements may impose additional or more restrictive conditions. Public approval does not release a property from applicable private obligations. The UDO preserves valid private covenants exceeding its standards and states that the Plan Commission does not enforce them.

• Private fence agreements: Under IC 32-26-3-1, adjoining owners choosing an arrangement for erecting, repairing, maintaining, or paying for a separating fence different from the statutory arrangement must use a signed written agreement recorded in the county or counties where the properties lie. This agreement requirement is separate from Madison’s written adjoining-owner approval for a fence placed on a property line.

REVIEW AND ENFORCEMENT CONTEXT

Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:

• UDO compliance: Fence height, right-of-way separation, dangerous materials, structural-support orientation, visibility, and applicable screening requirements.

• Historic review: Work requiring a COA, compliance with historic design conditions, and changes beyond an approved scope of work.

• Site and infrastructure conditions: Hillside disturbance, floodplain or floodway work, easement encroachment, watercourse obstruction, regulated-drain access, and blocked hydrants or meters.

• State and special-use duties: Residential-pool access control, Indiana 811 excavation procedures, qualifying agricultural partition fences, boundary hedges, malicious nuisance fences, and specified guard-dog kennel barriers.

• Complaint procedures: A written UDO complaint is filed with the Administrator, who investigates and may refer it to the Plan Commission, Board of Zoning Appeals, or their attorney. State fence statutes provide separate trustee or court procedures within their respective scopes.

USING THIS INFORMATION

This page provides general orientation on how residential fence rules are structured and applied within the City of Madison, Indiana. Updated November 2026.

In addition to local fence rules, certain Indiana laws apply statewide. See Statewide Fence Laws in Indiana.

It is not legal advice and does not replace official ordinances, permits, certificates, improvement-location approvals, development approvals, applicable building-code requirements, surveys, or professional guidance. Rules and interpretations may change, and application may vary based on zoning district, plan-commission jurisdiction, county zoning coverage, site conditions, subdivision/land-development status, easements, rights-of-way, floodplain or floodway status, stream conditions, stormwater or drainage requirements, regulated-drain conditions, road or highway conditions, INDOT jurisdiction, historic/design/special-district status, rural or agricultural context, livestock, lawful-fence or agricultural partition-fence context, live-fence or spite-fence conditions, local permit administration, pool-barrier use, Indiana 811 utility-excavation requirements, and private restrictions such as HOA covenants, deed restrictions, private agreements, recorded partition-fence agreements, or conservation easements. Before purchasing materials or beginning construction, confirm current requirements and site-specific limitations with the City of Madison Planning, Preservation and Design Department and any applicable private agreements. If this page conflicts with official ordinances, published guidance, adopted district guidelines, or direction from the City of Madison Planning, Preservation and Design Department, the official sources control. For legal advice or legal interpretation, consult a licensed attorney.