FENCE RULES – HARRISONVILLE (CITY), MISSOURI

OVERVIEW

This guide covers residential fences within the incorporated City of Harrisonville, Missouri, including applicable rural-residential and special-use conditions. Updated November 2026.

Harrisonville regulates a fence’s location and construction as well as its height. A front-setback fence must be low and open, while side and rear yards generally allow taller fencing. Corner lots, double-frontage lots and drainage easements need particular care because the apparent edge of a yard may not be its buildable fence line. New and qualifying replacement fences need city approval. Pools and designated historic properties add separate requirements, and the city’s recently adopted construction codes matter for barrier details. The rules below distinguish an ordinary yard fence from these property-specific conditions.

Quick questionHarrisonville answer
Permit or approvalRequired for new or extended fences and specified replacements; more-than-50% replacement and at-least-50% nonconforming reconstruction have distinct triggers.
Typical fence heightSide/rear: up to 6 feet. Front setback: decorative, at least 50% open and no more than 42 inches.
Placement & property linesFront-setback fence at least 6 feet from street right-of-way; corner, double-frontage, sight-triangle, easement and drainage conditions apply.
Common fence materialsWood: listed types and construction limits apply. Vinyl/PVC: vinyl is listed, with front-yard openness. Chain-link: allowed as open wire with metal posts; residential screening attachments prohibited.
Important local conditionsFence rules may be further affected by pools, historic designation, floodplain location, drainage, chicken enclosures, agricultural use and recorded restrictions.
Official local resourceHarrisonville Building Division

The table summarizes ordinary fence rules. The sections below explain the applicable conditions, exceptions and requirements for particular properties and uses.

GOVERNANCE

• City jurisdiction: These rules apply inside Harrisonville’s incorporated limits in Cass County. Harrisonville is a fourth-class city. Community Development administers the city’s building and fence requirements, with the Building Division processing permits and inspections. The City Engineer handles floodplain and drainage review; the Historic Preservation Commission handles designated historic property. County zoning does not replace the city’s own rules.

• Current construction codes: Harrisonville’s current building-code program uses the 2024 International Building Code, International Residential Code, International Property Maintenance Code and International Swimming Pool and Spa Code, effective August 31, 2026. The residential adoption deletes the model fence-permit exemption. The residential appendices adopted are BA, BB, BD, BE, BF, BN, BO, CA, CB, CC, CH and NF; Appendix NB is recommended. The property-maintenance adoption includes Appendix A and the pool-code adoption includes Appendix B. City amendments and the separate fence ordinance continue to apply.

• Agricultural division fences: Missouri has two county-dependent division-fence systems. A county vote under section 272.360 and commission order under section 272.370 activate the local-option system. Section 272.330(2) excludes counties with all or partial open range; subsection (1) applies the specified division-fence provisions even when a fence stands wholly on one side of the boundary. The applicable county system must be established before assigning construction costs. The two alternatives below apply to qualifying agricultural division fences, rather than automatically making every backyard fence a shared expense.

PERMIT AND APPROVAL REQUIREMENTS

• When a fence permit is required: Obtain Community Development approval before constructing a new fence or extending an existing fence. A replacement also needs a permit if it changes size, location or material, or replaces more than 50% of the linear length of the entire fence or an existing side- or rear-yard fence section. Chapter 505 separately requires a permit for new fence construction.

• Replacing a nonconforming fence: A legally existing nonconforming fence may be repaired. If 50% or more of the entire fence or a fence section is reconstructed or replaced, that fence or section must meet current city requirements. This conformity threshold includes exactly 50%; the replacement-permit wording above uses more than 50%.

• Application and inspections: The city’s permit forms and application portal provide the starting point. The building application asks for the address, parcel and legal description, zoning, start date, owner and contractor details, applicable designer information, description and class of work, valuation and relevant setbacks or special conditions. The Building Division also accepts small-project applications by telephone or email. Applicants schedule inspections at 816-380-8958.

• Permit fees: Fence fees follow the city’s comprehensive schedule through sections 405.565(C), 500.030 and 505.010. The 2026 fee schedule lists building-valuation fees of $40 for $0–$2,000; $40 plus $4 per $1,000 of valuation for $2,000.01–$10,000; $50 plus $5 per $1,000 for $10,000.01–$500,000; and $55 plus $5.50 per $1,000 above $500,000. Community Development determines the applicable fence valuation and fee calculation.

• Designated historic properties: The September 2026 historic ordinance requires a Certificate of Appropriateness for qualifying exterior changes to landmarks and historic-district property, including construction, alteration, removal, demolition and significant exterior features. Building or demolition permits cannot issue before the required historic approval. Ordinary maintenance and repair are excluded, and emergency safety work is limited to what is reasonably necessary; normal permits still apply. Historic staff determines whether a particular fence falls within routine or administrative review.

• Historic submission and decision: Provide photographs, plans, drawings, elevations, specifications, proposed materials and other requested information. The commission considers the application at its next regular meeting or a special meeting for routine business and issues a written decision. Work under a certificate must start within 6 months. Request an extension in writing before expiration, giving the reasons and original plans with any changes. An appeal of denial is due within 30 days of the denial date.

• Floodplain development: For property in the city’s mapped A or AE special flood hazard areas, the City Engineer administers Chapter 420 using the January 2, 2013 flood maps as revised. A separate permit is required before each covered construction or development project. Supply land identification, work description, use, value, floodway or fringe status, base-flood and proposed elevations, plans and a signed application, plus supporting information requested by the administrator. The comprehensive fee schedule applies.

• City private sewage systems: For houses or buildings used for employment or other purposes inside the city, abutting a street, alley or right-of-way containing a present or future city public sanitary sewer, section 700.590(D) requires suitable toilet facilities and connection at the owner’s expense within 60 days after official notice, provided the sewer is within 400 feet of the property line. The existing-system repair exceptions below remain relevant.

• Onsite installation and repair: Where public sewer is unavailable under that provision, a private system requires a written Building Official permit, requested plans and specifications, and the Chapter 525 permit and inspection fee. Notify the Building Official or Building Division when ready for final inspection and before covering underground portions; the city inspects within 24 hours of receiving notice. The permit becomes effective after satisfactory completion. New subsurface-absorption development needs at least a 3-acre lot, and a septic tank or cesspool may not discharge to a natural outlet.

• Existing onsite systems near public sewer: A sewer within 400 feet of a property line normally prevents a private-system installation, alteration or repair permit. Existing single-family or duplex conventional or professionally engineered systems with a property line more than 100 feet from city sewer may apply to repair, modify or replace components if all other state and local requirements are met. The Building Official may approve minor repairs not normally requiring a permit regardless of distance.

• State onsite-sewage scope: For a residential onsite wastewater treatment system, section 701.031 excludes a single-family residence lot of 3 acres or more, or a residential lot of 10 acres or more with no single-family-residence onsite system within 360 feet of any other onsite system and no more than one single-family residence per 10 acres in the aggregate. Neither alternative covers lots adjacent to lakes operated by the Corps of Engineers or a public utility. Every point of the system must be more than 10 feet from adjoining property lines, with no effluent entering adjoining property, contaminating surface water or groundwater, or creating a nuisance determined by a readily available scientific method. Outside the exclusion, construction, operation, major repair and major modification must comply regardless of the system’s original date. Valid more-stringent local requirements remain applicable. State household onsite jurisdiction is distinct from Department of Natural Resources wastewater jurisdiction.

FENCE PLACEMENT RULES

• Ordinary fence placement: The city’s supplemental fence regulations distinguish front, side, rear, corner and double-frontage locations. Within the front setback, keep the fence at least 6 feet from the street right-of-way. The right-of-way can extend beyond the curb or pavement. The yard’s applicable height and material limits are explained below.

• Corner-lot rear yards: For this rule, the rear yard is opposite the home’s front door. A rear-yard privacy, chain-link or decorative fence, wall or hedge may be up to 6 feet high abutting the front setback line. It may instead reach the rear property line only when the rear yard adjoins the rear yard of another corner lot, the homes face opposite directions and neither home has a driveway from the street beside both side yards.

• Double-frontage lots: Where the rear yard abuts an arterial, collector or local street, a fence, wall or hedge up to 6 feet high may abut the rear property line if it does not encroach into a platted landscape buffer, sight triangle, right-of-way or easement, and there is no direct access to the arterial or collector road.

• Easements and drainage: A platted easement may contain a fence only if the plat does not prohibit it and the owner removes the needed portion for city or utility maintenance access. If the owner fails to remove it, the city or utility may do so. Fences in drainage ways, detention areas or engineered swales may not pond water on adjacent land, divert water onto a neighbor or impede drainage.

• Drainage-maintenance access: Approved drainage easements provide at least 10 feet on both sides from the top of bank or toe of dam, or sufficient access for maintenance equipment. Fences interfering with that access or maintenance are prohibited. This access requirement follows the drainage feature and easement.

• Floodway effects: A regulatory-floodway encroachment requires hydrologic and hydraulic evidence that it will cause no increase in flood level. In numbered A or AE areas without a designated floodway, cumulative development may not increase base-flood elevation by more than 1 foot. The City Engineer applies these development standards to the proposed fence and site.

• Property lines and survey markers: A fence location depends on the boundary and recorded rights, not simply the edge of paving or an existing mowing line. Under section 60.355, anyone other than a land surveyor registered under Chapter 327 may not knowingly move, remove, deface or destroy a protected public-land-survey corner, property boundary marker, benchmark or horizontal-control monument. Violation is a class B misdemeanor. The statute states liability for reestablishment by a registered surveyor and gives an affected property owner a civil action in the county of violation, with damages limited to reasonable surveying costs and attorney fees.

• Public roads and drainage: Where section 229.150 applies, willfully and knowingly placing a fence across or upon a public-road right-of-way, putting a hedge inside established road lines, obstructing road drainage or diverting water onto the road is prohibited. Driveway and ditch crossings are subject to the road overseer’s or road-district commissioner’s supervision. The statute excludes charter counties and St. Louis City and preserves its specified soil-and-water conservation or Natural Resources Conservation Service technical-standard work and precision-level-grading farm/ranch exceptions.

• Existing road obstructions: Under that road statute, tracked written notice may require removal, approved repair or payment of reasonable costs. After 30 days from tracked delivery without compliance, the road authority may petition the associate circuit court. Entry to restore the road follows the opportunity for a hearing and a granted petition, within the authorized restoration scope. A granted petition can include reasonable work, court and attorney costs collected through a tax lien; if denied, the county bears the landowner’s court and attorney costs.

• Before digging or driving fence posts: Missouri’s underground-facility law covers private property as well as streets, rights-of-way and recorded utility easements. Digging with hand tools, augering, boring and driving are included. Except for statutory exceptions, give notice through the notification center at least 2 but no more than 10 working days before the expected start and obtain the required location information. The two-working-day calculation begins at midnight following receipt; Saturdays, Sundays and legally declared state or federal holidays do not count. A notice expires at 11:59 p.m., 21 consecutive calendar days from the stated work start date. Direct notice to a participating utility ordinarily does not replace center notice.

• What the excavation notice includes: Provide the filer’s and excavator’s required identity and contact information, the person responsible for the work, start date, depth, type of excavation and any trenchless work or explosives. Give a detailed accepted site location, distances, directions, landmarks, the excavation area relative to site features and access directions where needed. Physical or available electronic white lining can clarify a route. If an operator cannot identify the area, clarify it with white flags or paint, project plans or an on-site meeting.

• Facility responses and marking clarification: An operator ordinarily has 2 working days to provide the approximate location or a no-facilities response, unless the excavator agrees through the center to extend the start date and time. Work cannot start before the scheduled date unless all facilities are confirmed located. Either party may request an on-site marking meeting, held within 2 working days; by agreement, initial marking may occur there. Trenchless notices also require available depth information from the operator’s records to the best of its knowledge or ability.

• No response to a locate request: After compliant original notice, an excavator must send a second no-response notice through the center before starting. The operator then has 2 hours to mark or contact the excavator with its marking time. A no-response notice made by 2 p.m. requires marking that working day; one made after 2 p.m. requires marking by 10 a.m. the next working day. Work may commence only if the operator fails to mark or contact as required by section 319.030(4), with the legally required care still in place.

• Keeping a locate valid: Work is limited to the notified area, visible marks and the notice’s unexpired life. If excavation cannot begin within the stated 10-working-day period, request relocation before starting. If weather, construction or another cause makes marks unusable, request remarking through the center using the original notice procedure and response period. Preserve marks with reasonable care; avoidable damage to them or repeated unnecessary remark requests can result in reasonable remarking charges. Only the facility owner or its representative may mark or relocate a facility. Visible paint does not extend an expired ticket.

• Safe excavation and unexpected facilities: The approximate location generally extends the facility’s width plus 2 feet on each side; reinforced concrete, multiple adjacent facilities or other specified unusual conditions can require a wider designation. Before work, determine best practices for confirming horizontal and vertical location in the site’s geology, access and pavement conditions. Hand or soft digging must be used as a best practice when possible. Notify the center of an incorrectly located or unmarked facility; the owner must contact the responsible excavator or correctly locate it within 2 hours and correct erroneous records. Notice compliance does not remove the duty to excavate carefully and prudently.

• Damage, emergencies and private lines: Report damage, dislocation or disturbance to facilities and their protective items, including trace wires, encasements, cathodic protection and permanent stakes. Immediately call 911 if pipeline contact or damage releases hazardous liquid or gas. Do not conceal damage or repair without owner authorization. After notification, temporary emergency sewer repairs may prevent further damage without advance authorization; reporting still applies. Genuine emergency excavation requires reasonable precautions and notice as soon as practical; notified operators must mark or contact within 2 hours and state when marking will occur if delayed.

• Limits of a locate ticket: The law’s exclusions include agricultural tilling no deeper than 16 inches and installing marking flags or stakes, not every farm-post or hand-tool project. Gas distribution lines, electric lines, telecommunications or broadband facilities, cable television facilities, water service lines, water systems, storm-drainage lines and sewer-system lines on private property are excluded when owned solely by that property’s owner or owners and receiving service, unless they are used for vehicular traffic control, street or highway lighting, or emergency-response communications. This exclusion does not apply where they cross or lie within an easement or right-of-way dedicated to public use or owned by someone other than that private-property owner. Solely property-owner-owned water and sanitary sewer service lines are excluded at any location, as are structures carrying only stormwater under roads, drives or railways. A ticket therefore does not promise that every private line has been marked. Excavation in a state highway or its right-of-way also requires the highway commission’s permit, subject to the railroad-right-of-way exception.

• General-law division-fence allocation: If the general-law system governs, give written notice of intended division-fence work. The usual allocation is the right-hand portion as each owner stands at the center of the common boundary on their own land facing the line. A disagreement can go to a judge and three disinterested viewers, with 3 days’ notice and $25 per viewer per day taxed as costs. A different signed agreement, recorded with descriptions of the land and fence portions, binds heirs and assigns.

• General-law need, repair and removal: Under that system, if only one neighbor needs the fence, that owner bears the initial cost. Recording the cost on the deeds preserves the later half-reimbursement obligation if the other owner begins using the fence for livestock. Neighbors may agree no fence is needed or agree to exceed the lawful standard. Each owner maintains the assigned portion, with the statutory adjacent-land entry for repairs. Removal requires all owners’ consent except where the dividing line is a public road or highway.

• Local-option division fences: If the county has activated the local-option system, either neighbor’s need ordinarily obligates both unless they agree no fence is needed. After notice, the other owner has 90 days to construct their half before the statutory court process. The neighbor’s payment is capped at half the value of a lawful four-barbed-wire fence even if a more costly fence is chosen. The lawful construction standards appear below.

• Opening gates and removing partition fences: Section 537.350 addresses voluntarily opening or throwing down another person’s enclosure and leaving it open, and removing a partition fence adjoining cultivated fields without 6 months’ written notice to the adjoining owner. Its remedy is $5 plus double resulting damages and costs. Notice does not replace separately required ownership consent. Under section 537.360, probable cause to believe the land or property was one’s own limits recovery to single damages with costs.

• Watercourse exception to fence-removal liability: Section 537.350 has a separate exception for fences across watercourses carrying enough water to move lumber logs at least 10 inches in diameter, railroad ties and piling. Those driving or placing such material to float it remain liable for actual damage to adjoining owners. The provision excludes stream fences that enclose no farm or plantation, or are erected merely to obstruct passage or extort payment. This narrow watercourse rule does not settle ordinary yard-fence ownership.

• Family burial grounds: A qualifying abandoned family or private burial ground includes land not deeded to the public with no interment for at least 25 years. Knowingly injuring or removing protected grave features or their protective or ornamental fence or railing is prohibited. Where private land completely surrounds the burial ground with no public access, reasonable access for customary visitation at reasonable hours is protected and enforced by the county sheriff. Statutory court authority over removal or disinterment remains separate.

• A boundary beside a state park or historic site: For an actual common boundary where fencing would prevent livestock or commercial-game intrusion, 10 CSR 90-2.070 allows Division of State Parks participation. Submit a written Fencing Request Form for director or designee approval. The division inspects need, resources, materials, reasonable cost and boundary accuracy; a required survey is shared equally in cost. Written approval or denial is due within 60 days of form receipt.

• Approved park-boundary construction: The landowner builds on the identifiable or verified boundary, protects park resources and does not alter soil or debris elevations to drain wetlands or impound water on department land. Variances need written approval. The division supplies construction materials as its cost share and monitors the work. Owner and successors maintain the fence; park-side brush clearing extends no more than 3 feet inside the boundary. Vehicle/equipment access and herbicide use or drift onto park vegetation require manager permission. Overhanging branches may be trimmed at the boundary up to 8 feet high. Removal needs written division consent except temporary repairs. Participation excludes saltpeter works, cotton gins, poisonous-crop land and cases where other law or judgment requires the owner to fence their own land.

FENCE HEIGHT AND VISIBILITY RULES

• Yard heights and measurement: Ordinary side- and rear-yard fencing may be up to 6 feet. Within the front setback, only decorative fencing is allowed, no higher than 42 inches and at least 50% open. Measure height vertically from the fence top to the adjacent ground on its exterior side. The corner and double-frontage placement rules still apply.

• Street and driveway sight triangles: Keep signs, fences, walls, shrubs and other obstructions between 2 and 8 feet high out of the sight triangle. At street intersections, measure 30 feet along each intersecting right-of-way line. At a driveway or vehicle access intersection, measure 30 feet along the street right-of-way and driveway edge from their intersection. An arterial meeting another arterial or a railway uses 50-foot legs. The city may trim, remove or order removal of an obstruction.

• Additional subdivision-road visibility: Where section 410.160 applies, outside the central business district the sight position extends at least 20 feet along the minor road, with clear view along the major road of 215 feet for an arterial, 170 feet for a collector or 130 feet for a local street. Obstructions above 2 feet over the road surface must not block that view. In the central business district, the City Engineer approves the closest practicable compliance. These road-design sight distances apply alongside the fence-specific triangles where both govern the site.

• General-law agricultural fence standard: Where Missouri’s general agricultural-fence law applies, a lawful fence is the agreed or court-decided wire or board construction at least 4 feet high, on firmly set posts no more than 12 feet apart, with members secured and spaced to resist horses, cattle and similar stock. This is the standard for the qualifying livestock enclosure, not an ordinary yard-fence height maximum.

MATERIAL AND CONSTRUCTION LIMITS

• Wood, vinyl and chain-link: Wood: decorative forms include split rail and wood rail; privacy fencing may use treated wood, with boards no wider than 12 inches. Vinyl/PVC: vinyl is listed for decorative and privacy fencing, subject to front-yard openness. Chain-link: open-wire fencing uses chain link and metal posts. Screening of any type may not be woven through or attached to chain link in a residential district. A residential pool barrier must meet that local restriction as well as its pool-opening requirements.

• Other materials and construction: Decorative examples include brick or stone walls, wrought iron, square tubing and metal pipe, with the decorative openness requirement still applicable. Privacy fences may use high-quality decorative block, brick, stone, treated wood, vinyl or ornamental metal; other materials are considered case by case. Construct fences in a workmanlike manner. Use no more than two different fence material types. The finished surface faces outward and horizontal and vertical supports remain inside the enclosure. Exposed metal other than galvanized metal needs a colored finish.

• Barbed and electric fences: Barbed-wire and electrically charged fences are prohibited in residentially zoned areas and within 4 feet of a public sidewalk in any district. In nonresidential zones, barbed wire is allowed atop a security fence at least 6 feet high. Agricultural-zoned property that does not abut a residentially zoned area has the stated exception allowing electric and barbed-wire fencing at any height; the sidewalk provision remains a separate condition.

• Maintenance and historic character: Maintain fences upright and preserve painted or similar finishes. Replace missing boards, pickets and posts promptly with the same type and quality of material. The property-maintenance code also requires sound, maintained fences and retaining walls. On designated historic property, preserve distinctive materials, features and craftsmanship; repair rather than replace where feasible. Replacement should match composition, design, color, texture and visual qualities, and new work should be compatible in scale, setback and materials. The Historic Preservation Commission administers these requirements, including fence and gate maintenance.

• Household chicken enclosures: Up to 6 hens per tract may be kept under the city’s conditions, in the rear yard with written consent from contiguous property owners and residents. Property issues go to Community Development and animal-welfare issues to Animal Control. Hens stay in the rear enclosure and are housed overnight. Keep it clean, dry, odor-free and ventilated, with sun and shade and protection against rodents, wild birds and predators.

• Chicken housing and separation: The henhouse needs an enclosed roof and doors locked at night; vents use bird- and predator-proof wire with openings under 1 inch. Use uniform materials, not scrap or waste boards or sheet metal. A henhouse, tractor or pen must be at least 10 feet from a property line and 25 feet from an adjacent dwelling, church, school or business.

• Private pool barrier and cover options: The adopted swimming-pool code requires barriers for outdoor pools and spas and indoor swimming pools. An ASTM F1346 lockable spa or hot-tub safety cover, or a complying powered swimming-pool safety cover, provides the code’s stated exception from sections 305.2–305.7. The property-maintenance code independently covers private pools, spas and hot tubs with water deeper than 24 inches, including its safety-cover exceptions with functioning controls. Existing enclosure effectiveness may not be reduced.

• Pool construction and barrier height: An in-ground pool or spa site needs a fence at least 4 feet high from first excavation until the permanent barrier is complete. A permanent barrier’s top must be at least 48 inches above exterior grade around the whole perimeter and for 3 feet horizontally outside it. Bottom clearance is no more than 2 inches over grass, gravel or other nonsolid ground, or 4 inches over a solid surface. A barrier mounted on an above-ground pool or spa has a maximum 4-inch gap above the structure.

• Pool barrier openings: Openings must not pass a 4-inch sphere. A solid barrier may not have handholds or footholds except normal construction tolerances and tooled masonry joints. Where horizontal-member tops are less than 45 inches apart, members face the pool and vertical gaps and decorative cutouts are no wider than 1¾ inches. At spacing of 45 inches or more, vertical openings may be up to 4 inches, with decorative cutouts still limited to 1¾ inches.

• Chain-link and diagonal pool barriers: Chain-link openings may not exceed 1¾ inches. Although the model allows secured slats to reduce openings, Harrisonville’s residential screening ban requires another compliant design in residential zones. Diagonal-member openings also may not exceed 1¾ inches, and the members may be no more than 45 degrees from vertical.

• Pool screen and mesh systems: A screen enclosure used as a barrier must satisfy the barrier rules and be designed by a registered design professional; it is not treated as a dwelling wall. Barrier mesh needs tensile strength of at least 100 pounds per square foot under ASTM D5034 and ball-burst strength of at least 150 pounds per square foot under ASTM D3787. A mesh fence must follow its manufacturer’s instructions and ASTM F2286; hinged gates follow the gate rules, and mesh cannot be installed atop an onground residential pool. Keep the inside of a mesh fence at least 20 inches from the nearest water edge.

• Pool equipment and gates: Equipment on the same lot outside the barrier, including pumps, filters and heaters, must be at least 36 inches from its exterior. Pedestrian barrier doors and gates open away from the pool, self-close, self-latch and accommodate a lock; they may not swing over stairs. Nonpedestrian service doors and gates stay locked when unused. Multiple doors or gates need at least one secured leaf and an adjacent self-latching leaf. For existing barriers, the property-maintenance code requires a gate to close and latch positively from an open position 6 inches from its post.

• Residential pool latch locations: An outside-access latch that is not self-locking must be at least 54 inches above finished floor or ground. With a self-locking device operated by a key, electronic opener or integral combination lock, its control and release must be no higher than 54 inches. A private-pool latch accessible only from the pool side must be at least 3 inches below the gate top. Openings in the door, gate or barrier within 18 inches of an inside latch may not exceed ½ inch in any dimension. The property-maintenance code separately places a release below 54 inches from the gate bottom on the pool side.

• A house wall forming part of the pool barrier: Direct access through doors, gates or operable windows with sills below 48 inches above the indoor floor requires the code’s protection: a water-hazard entrance alarm listed and labeled in accordance with UL 2017 that sounds when the window, door or their screens are opened, a safety cover listed and labeled in accordance with ASTM F1346 or an approved equivalent such as a self-closing, self-latching door. Ordinary dwelling alarm-deactivation controls are at least 54 inches above finished floor; accessible, Type A or Type B dwellings and nondwelling structures use 48–54 inches.

• Onground pool walls and access: A pool wall alone can serve as the barrier if the manufacturer permits it, its bottom is on grade and its top is at least 48 inches high around the entire pool, with the other barrier requirements met. A wall with a mounted barrier must likewise reach 48 inches and meet those requirements. Access ladders or steps must be capable of being secured, locked or removed unless enclosed by a complying barrier. Openings created by securing, locking or removing them may not pass a 4-inch sphere. Install mounted barriers according to the manufacturer’s instructions.

• Natural pool boundaries: A barrier between the pool and a natural waterbody is unnecessary only where the pool abuts that waterbody, public shoreline access is not permitted and required barriers extend at least 18 inches beyond the water’s edge. Natural topography preventing direct access requires governing-body approval and protection equivalent to the specified barrier requirements.

• Local-option agricultural construction: Where the local-option system applies, its lawful fence can use at least four boards per 4 feet of height, with gaps no more than twice the board width and substantial posts no more than 12 feet apart with one stay. Alternatively, four barbed wires may use posts no more than 15 feet apart with a stay, or 12 feet apart without one; an equivalent fence is allowed. Local material restrictions still apply where the property is also under a municipal code.

• Livestock containment: Section 270.010 prohibits permitting horses, mules, asses, cattle, swine, sheep or goats to run at large outside their enclosure. A person or officer taking up the animals must give a known owner written notice within 3 days stating the keeping/feeding compensation and damage claim. Reasonable taking-up, keeping and feeding compensation and actual damages apply. The stray-law process applies when the owner is unknown, or after notice fails to pay taking-up, feeding and keeping compensation. For a public-road or highway accident, the owner’s defense requires establishing that escape occurred without their fault or negligence.

• Residential lagoon fence: For a lagoon governed by the household onsite standard, enclose the pond with a fence at least 4 feet high, using welded, woven or chain-link wire no smaller than 14 gauge. Cattle or hog panels may substitute with tee-post line posts. Use pressure-treated wood or galvanized and/or painted steel posts, driven, tamped or set in concrete. Line posts may be no more than 10 feet apart; corner posts must be braced. Construction must be sound, with no gaps or openings along the bottom.

• Lagoon placement, gate and completion: The fence must be no closer to the water’s edge than the center of the berm at the 3-foot-deep operating water level. Install a properly hinged 4-foot-high gate of comparable material with an effective latch, and complete fencing before dwelling occupancy. The rule recommends, rather than mandates, line posts at least 18 inches deep, corner posts at least 24 inches deep, a setback no more than 30 feet from the water’s edge and a gate 36–48 inches wide for maintenance equipment.

• Licensed family childcare homes: An outdoor play area must be on or adjoining the home’s property and safely accessible. Fence it when necessary against traffic, water or other hazards. For homes initially licensed after the rules’ effective date, and for new fences at existing facilities, fencing must be at least 42 inches high. Independently of that height cohort, fences must prevent children from crawling or falling through or becoming entrapped.

• Childcare pools and animals: Swimming and wading pools must be fenced against child access. For family childcare homes initially licensed after the rules’ effective date, pool fencing must be at least 42 inches high with a locked gate. Above-ground pools may use a 42-inch fence around the top with pool-deck steps barricaded. Animals threatening children’s health or safety must be absent or securely penned where children cannot reach them. These licensed-home duties apply alongside other applicable pool rules.

• Permitted captive cervids: Where keeping captive cervids is lawful and permitted, enclosure fencing and posts must reach at least 8 feet along the entire enclosure. Use wire no smaller than 12½-gauge woven or high-tensile woven wire, 6-gauge welded wire, 9-gauge chain link, or wood planks. Vertical wire or plank gaps may not exceed 6½ inches. Stacked fences require at least a 6-inch overlap and firm attachment no more than 3 feet apart, or combination and firm attachment no more than 12 inches apart. Ground clearance may not exceed 3 inches.

• Captive-cervid enclosure upkeep: Clear woody vegetation under 6 inches in diameter at breast height for at least 6 feet inside and 6 feet outside on controlled land. For enclosures or additions constructed after June 30, 2019, the separate provision requires all woody vegetation cleared 6 feet inside and outside. Fell dead trees on controlled land taller than their distance to the fence. Posts must maintain fence integrity; gates must be locked and latched and meet or exceed fence standards. Maintain water gaps, stream crossings and terrain protection against ingress and egress at all times, using supplementary posts, grading or fencing where necessary.

PRIVATE RESTRICTIONS

• Recorded and private restrictions: Recorded covenants, homeowners’ association architectural rules, private easements and agreements about fence ownership, maintenance or cost can affect a project separately from government approvals. Review the documents governing the property. A permit does not determine the true boundary, authorize encroachment or resolve a private cost dispute. Statutory agricultural division-fence duties and the public road, drainage and plat requirements explained above remain separate.

REVIEW AND ENFORCEMENT CONTEXT

Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:

• City approvals and site conditions: Review can address required fence permits, replacement thresholds, yard heights and materials, street visibility, drainage access, historic approval, floodplain effects and applicable pool barriers. The corresponding rules and procedures are explained above.

• Conditional uses and private disputes: Livestock, licensed childcare, onsite lagoons and permitted captive-animal enclosures carry their own conditions when present. Government approvals remain distinct from boundary ownership, recorded restrictions and private fence-cost disputes.

USING THIS INFORMATION

This page provides general orientation on how residential fence rules are structured and applied within the City of Harrisonville, Missouri. Updated November 2026.

In addition to local fence rules, certain Missouri laws apply statewide. See Statewide Fence Laws in Missouri.

It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with the identified municipality, including its actual municipal or county class, charter, adopted program or special district, and each function’s verified territory, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Missouri law. Applicable requirements depend on the property’s actual facts and the respective authority of the identified offices. Private agreements and recorded rights remain separate from government approvals. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern.