FENCE RULES – KIRKWOOD (CITY), MISSOURI
OVERVIEW
This page covers residential fences inside the incorporated City of Kirkwood, Missouri, in St. Louis County. A Kirkwood mailing address does not bring property outside the city limits under these municipal rules.
Kirkwood requires a permit for constructing or rebuilding a fence, with a published $48 fee. Most fences are limited to six feet, while fencing before the addressed front of a home is limited to four feet and must be at least one-third open. Street-facing material restrictions apply more broadly than that addressed-frontage height rule. Curb, sidewalk, right-of-way and intersection clearances can prevent a fence from reaching a property line. Pools, designated historic properties, flood-prone sites, drainage and work near protected trees have additional requirements. Updated November 2026.
| Quick question | Kirkwood answer |
|---|---|
| Permit or approval | A permit is required to construct or reconstruct any fence. The published fee is $48; a site plan is required. Separate approvals apply to qualifying site conditions. |
| Typical fence height | Ordinarily 6 feet, with posts up to 6 inches higher. Before the addressed front building line: 48 inches and at least one-third open, subject to the stated exceptions. |
| Placement & property lines | Property-line placement is allowed only after the 12-foot curb, 25-foot intersection, 1-foot public-way/sidewalk and other applicable restrictions are met. No fence may occupy public right-of-way. |
| Common fence materials | Wood: subject to construction and front-material restrictions. Vinyl/PVC: not expressly prohibited by the ordinary material list. Chain-link: prohibited before front building lines along every street frontage of residentially zoned or occupied lots. |
| Important local conditions | Fence rules may be further affected by private pools, corner or through lots, designated landmarks and local historic districts, tree protection, floodplain development, grading, drainage, public ways and recorded rights. |
| Official local resource | Kirkwood Fence Permits |
The table summarizes ordinary fence rules. The sections below explain their frontage distinctions, exceptions and property-specific requirements.
GOVERNANCE
Kirkwood is a home-rule city, incorporated in 1865. The City Council adopts its municipal requirements. The Building Commissioner administers the fence code; Planning and Development Services administers zoning. The city uses locally amended 2021 International Building, Residential, Swimming Pool and Spa, and Property Maintenance Codes, effective April 1, 2026, alongside its separate fence and zoning provisions.
The Landmarks Commission reviews the designated properties and work described below. The Urban Forester administers tree protection. The Director of Public Services administers grading and relevant public-way work, and the Building Commissioner is the Floodplain Administrator. City Council and Board of Adjustment approvals have their own defined roles. These municipal functions govern property within Kirkwood, rather than all of St. Louis County.
PERMIT AND APPROVAL REQUIREMENTS
• Fence permit, definition, plans and fee: The city fence ordinance requires a permit for construction or reconstruction of any fence. It defines a fence as a structure serving as an enclosure, wall or barrier constructed of posts, supports, boards, wires, stakes, rails, masonry or stone. The application identifies height, type and construction materials and includes a site plan showing the fence, property lines, street curb, sidewalk and house. The plan need not be prepared by a surveyor. City guidance recommends a survey and directs applications through the Kirkwood Public Portal. The published fence permit fee is $48.
• Fence-article exceptions: Temporary construction fences and the article’s specified public/utility, bridge, roadside retaining-wall, culvert and open-drainage safety installations are exempt from that article. This does not remove a separately applicable pool, excavation or tree-protection duty.
• Existing fences and replacement: Fences must remain structurally sound, in good repair and free of loose or vibrating parts. A lawfully existing nonconforming fence may remain and be maintained if it is not unsightly. Repair or replacement of 50 percent or more within one year requires conformity with the fence article. The article also separately states that any replacement of 50 percent or more requires conformity. Permission to maintain an existing fence does not remove the permit requirement for reconstruction.
• Designated landmarks and local historic districts: Before issuing a building permit for an exterior or site alteration to a designated landmark, the city requires Landmarks Commission approval. New construction within a local historic district requires Commission review and approval for adherence to that district’s guidelines. Complete applications are reviewed within 60 days, unless the applicant agrees to extend the period. Failure to decide within the applicable review period results in deemed Commission approval; the Building Commissioner still grants or denies the permit under applicable requirements. The city historic-preservation directory identifies local designations and the applicable guidelines. National Register listing alone is not the same local approval condition.
• Architectural review distinction: Ordinary fences are expressly exempt from Architectural Review Board review. That exemption does not remove the separate Landmarks Commission requirement for designated properties. A proposed historic fence’s appearance and placement remain subject to the applicable guidelines and approved design.
• Historic demolition and relocation: A demolition or relocation permit for a designated landmark or property in a local historic district enters a separate Landmarks review that may withhold approval for 270 days. The Commission may approve earlier but cannot terminate its review within 60 days after initial review. This is the demolition/relocation process, not an automatic delay on every fence repair.
• Mapped floodplain development: Construction or other development in the city’s mapped A and AE flood-hazard areas requires a separate floodplain development permit. The ordinance adopts the identified St. Louis County flood-map panels dated February 4, 2015, as amended and revised. The written application identifies the land, work, use, assessed value and improvement value, floodway or fringe location, existing base-flood and proposed elevations, plans and specifications, and the permittee or authorized agent. The Building Commissioner administers the application.
• Grading: A grading permit from the Director of Public Services is required unless a stated exemption applies. Temporary placement of clean earth, rock or stone for landscaping on occupied property is exempt only within the ordinance’s elevation limits; its small-berm exception requires a berm less than 1 foot high and less than 100 square feet. Specified excavation associated with a valid city permit, including single-family additions, accessory work, retaining walls, driveways, utilities or demolition, and city work have their stated exemptions. A fence permit alone is not a general grading exemption.
• Grading plans and erosion controls: A grading application includes a schedule and three copies of the plan, with two-foot contours, elevations, watercourses, drainage and erosion/dust controls. Engineering seals and Metropolitan St. Louis Sewer District review are required where applicable. Sediment and dust protection for adjoining property must operate throughout land disturbance until ground cover is established. Approved silt controls must be installed and maintained; inadequate controls can result in a stop-work order.
• Impervious-area work accompanying a fence: Current infill stormwater provisions apply to development creating at least 1,000 square feet of net additional impervious area or meeting the ordinance’s 25-percent lot-impervious-area trigger, with the stated capture requirement for the first 1.14 inches of runoff. A separate ordinance changes those requirements beginning April 1, 2027; its 750-square-foot and 1.25-inch provisions are not yet effective in November 2026. The capture area is the net additional impervious area for the first trigger, or the greater of net additional impervious area and the area above the 25-percent lot threshold for the second. Development required to provide sewer-district stormwater quality/quantity controls is exempt from those two capture items. New/redevelopment disturbing at least 1 acre, including a larger common project, needs sewer-district plan approval before building permits. If the required 1.14-inch treatment is impractical, downstream drainage improvements mitigating a known flooding problem may be considered with a professional engineer’s assistance for all or part of the treatment requirement. The Director of Public Services makes the final determination on that alternative. An ordinary open fence is not automatically such impervious-area development.
• Public-way work: Excavation in a public place, street, roadway, parkway, walkway, alley, right-of-way or easement requires a separate permit from the Director of Public Services or Building Commissioner for each separate work location. The permit program restricts applicants to licensed contractors or public utilities and exempts city public work. Erecting a gate, fence or other obstruction in a public or private street requires City Council approval; temporary closures use the specified administrative approval after fire and police review.
• Tree-related approval: A Building or Engineering permit project involving new construction, demolition, excavation, grading, complete redevelopment or clearcutting requires an Urban Forester-approved tree-protection plan and certified-arborist tree study. Partial development, including additions or exterior alterations affecting 33 percent or more of the lot, also requires them. For a smaller partial project with grading or construction impacts within 10 feet of a significant or city tree, protection measures must be installed and maintained, but a tree study is not required under that smaller-project provision.
• Fence appeals and variances: An appeal from the Building Commissioner’s fence decision goes to the Board of Adjustment within 30 days. The Board may correct an erroneous interpretation or grant a variance on the article’s hardship grounds, including unusual lot configuration or historic restoration. Mere loss of a possible advantage or convenience is not undue hardship. The proposal must satisfy the light-and-air, safety and neighborhood standards. Notice goes to owners within 100 feet. An aggrieved designated-property owner may separately appeal a Landmarks Commission decision in writing to City Council within 15 days; Council review occurs within 31 days.
FENCE PLACEMENT RULES
• Property lines and public clearances: A fence may be placed on a property line only if all other restrictions are satisfied. It may not occupy public right-of-way, lie within 12 feet of a public street curbline, or lie within 1 foot of a public right-of-way, public walkway or public sidewalk. It also may not lie within 25 feet of the point where the curbs or edges of two streets intersect. That intersection rule is measured from the curb/edge intersection, not as a 25-by-25-foot triangle along private lot lines.
• Zoning yards: The zoning provisions except fences complying with the fence article from general structure-setback calculations and allow compliant fences and walls within required front, side and rear yards. House and accessory-building yard dimensions therefore are not an additional ordinary fence-setback schedule. The fence article’s own street, height, openness and material conditions still apply.
• Easements, streets and hydrants: A location on private land must respect recorded utility, access and drainage rights. City permission for a fence does not enlarge those rights. Fences and other stationary obstructions may not occupy a street, alley or sidewalk unless authorized by ordinance. A fence must not obscure, obstruct or restrict access to a fire hydrant or Fire Department connection, including those on private property or private streets.
• Watercourses and runoff: Grading, filling or excavation may not divert or reduce a natural or established watercourse except through an approved development/grading permit and applicable sewer-district approval. Blocking stormwater entry to the drainage system requires city or sewer-district approval; private drainage systems must be maintained. Grading must use clean fill, avoid harmful runoff and ponding, and maintain slopes no steeper than 3 horizontal to 1 vertical unless authorized. These standards apply even where grading is permit-exempt. Stormwater/sump-pump pipes may not discharge within 10 feet of an adjacent property line, except the stated roof/foundation discharge within 2 feet of the house; natural swales/creeks have their stated treatment. This is not a required gap under every fence.
• Sump-pump discharge controls: Projects installing a sump pump, or existing sump pumps whose discharge causes the specified nuisance, must discharge to either a drywell treating at least 175 square feet of contributing area and at least 10 feet from any property line, or a vegetated filter strip treating at least 175 square feet, with discharge at least 20 feet from any property line. These measures may count toward required infill stormwater controls. This is the current sump-pump branch, separate from an ordinary fence’s location.
• Flood-prone fence sites: Before a regulatory floodway is designated, cumulative proposed, existing and anticipated development in a numbered A or AE zone may not increase the base-flood water level more than 1 foot anywhere in the community. In a designated floodway, encroachment requires the specified hydraulic and hydrologic demonstration of no increase. Applicable development must be adequately anchored against flotation, collapse and lateral movement, use flood-resistant materials and minimize flood damage. A dwelling’s floor-elevation rules are not a fence-height formula.
• Historic fence placement: General Landmarks guidelines recommend preserving historic fences and retaining walls, using traditional materials and designs suited to the house and district, placing new fences behind the front elevation, and placing privacy fences at or behind the rear elevation. Front-yard enclosure that interrupts continuous neighborhood lawns is discouraged. Chain-link enclosures should be outside public view or screened with a traditional fence or evergreens. These are designated-property design preferences, not additional citywide fence bans.
• Central Place and other local districts: Central Place’s guidelines recommend natural fencing that is open and lower in scale and discourage chain-link or decorative plastic border fencing. They also recommend retaining mature trees and natural topography and avoiding grading harm to drainage, soil stability or trees. Applicable district guidelines and Landmarks approval determine a designated property’s design; there is no single additional numeric historic-fence limit stated here. Sugar Creek Ranch’s guidelines concern compatible residential design and do not turn a siding restriction into a general fence-material ban.
• Boundary trees: A required tree-protection plan must include signed adjacent-owner authorization for removal of a tree on a shared property line or entirely on adjacent property. Public-tree rules also prohibit attaching ropes, wires, nails or other contrivances to a public tree. A fence permit does not authorize using a public tree as a fence post or removing a neighbor’s tree.
• Survey markers: Missouri Section 60.355 protects the listed public-land-survey corners, boundary markers, benchmarks and horizontal-control monuments from knowing movement, removal, defacement or destruction by a person other than a registered land surveyor. It provides restoration-cost liability and the affected owner’s stated surveying-cost and attorney-fee remedy, alongside its misdemeanor classification. Fence construction does not authorize disturbing a protected marker.
• Notice before digging: Fence-post digging, augering and driving are covered by Missouri’s underground-facility law, including on private property. Notice through Missouri 811 is required at least 2 but no more than 10 working days before the expected start. The period begins at midnight after receipt and excludes Saturdays, Sundays and legal holidays. Notice gives the required excavator/responsible-person, location, start, depth, work and contact details. Limited tillage or temporary-marker exclusions are not a general structural-post exemption. Separately owned private lines are not a promise of universal location service.
• Utility responses: Participating operators ordinarily supply approximate locations or no-facilities responses within 2 working days, unless an extended start is agreed through the center. Work may begin before the scheduled date only after confirmation that all facilities are located. Either side may request a marking-clarification meeting within two working days; a trenchless notice also requires available depth information. An insufficient site description must be clarified by white markings, plans or an on-site meeting.
• Unanswered original notice: Under Section 319.030, an operator’s failure to respond to a proper original notice requires a second notice through the center before excavation. The operator then has 2 hours to mark or contact the excavator with its marking time. A second notice by 2 p.m. requires marking that working day; a later notice requires marking by 10 a.m. the next working day. Only failure to mark or contact as that subsection requires permits excavation after this process. The duty of care remains.
• Ticket life, markings and location care: A notice expires at 11:59 p.m., 21 consecutive calendar days from the work start date. Work may continue within its described area while valid and markings remain visible. Failure to begin within the stated ten-working-day period requires a relocate request before starting. Unusable marks require remarking with the original notice/response timing. Reasonable care to preserve marks is required; careless or repeatedly unnecessary remark requests can create cost liability. The approximate-location strip ordinarily is the facility width plus 2 feet on each side, with a wider operator designation for the specified unusual conditions. Before digging, determine best practices for horizontal and vertical confirmation; use hand or soft digging when possible. An incorrectly located or unmarked facility must be reported through the center, with an operator response within 2 hours by contact or correct location.
• Damage, emergencies and state highways: Damage, dislocation or disturbance of an underground facility or its trace wires, encasements, cathodic protection, permanent stakes and other protective items must be reported to the center. Pipeline contact/damage causing hazardous-liquid or gas release requires an immediate 911 call. Damage must not be concealed; repairs need the owner’s authorization. Narrow emergency temporary sewer repairs may follow notification to prevent further damage without advance owner authorization, but reporting still applies. Genuine emergency excavation requires reasonable precautions and notice as soon as practical; the operator must mark or contact within 2 hours and state its marking time if marking cannot be completed then. Excavation in a state highway or its right-of-way separately requires transportation-commission permission, subject to the railroad-right-of-way exception.
• Division fences: Missouri’s general and county-adopted local-option partition-fence systems have their own livestock, contribution, repair and removal conditions. They do not require every neighbor to pay half of an ordinary privacy fence. General-law division-fence removal requires the owners’ consent except for opening a public road; the local-option text has the additional repair exception. Repair entry is a system-specific right, not general permission to enter neighboring land to construct a new fence. The applicable system and agreement govern; municipal approval settles neither ownership nor contribution.
• Livestock on residential acreage: Section 270.010 prohibits permitting horses, mules, donkeys, cattle, swine, sheep or goats to run at large outside their enclosure. Anyone may restrain them, and a sheriff or officer with police powers must do so. Written notice to a known owner is due within 3 days, stating feeding/keeping compensation and claimed damage. Reasonable taking-up, feeding and keeping costs plus actual damage are recoverable under the statute; an unknown owner or unpaid stated compensation leads to the stray-law process. In a public-road accident, the statutory defense requires establishing escape through no fault or negligence of the owner.
FENCE HEIGHT AND VISIBILITY RULES
• Ordinary height and measurement: Fences ordinarily may not exceed 6 feet. Measure vertically from the topmost fencing material to the ground. Posts may project up to 6 inches above the fencing material.
• Addressed front of a residence: In front of the front building line of residentially zoned or residentially occupied property, the maximum is 48 inches. On corner, through and multiple-frontage lots, this reduced height applies only to the frontage on which the house is addressed. The other street frontages remain subject to all other applicable restrictions.
• Front openness: Fencing in front of the addressed front building line must be at least one-third open. A stone or brick wall no higher than 36 inches is exempt from this openness requirement. The exception does not remove location or other applicable restrictions.
• Private tennis courts and special approvals: Open-mesh fencing around a tennis court may be up to 15 feet high. Fences approved by the Planning and Zoning Commission or City Council through site-plan, special-use or other special procedure are exempt from the ordinary fence article under its stated approval exception. The property’s approved plan determines that special treatment; it is not a general right to exceed the ordinary height.
• Private-pool minimum: Under the adopted Property Maintenance Code, private pools, hot tubs and spas containing water more than 24 inches deep need a barrier at least 48 inches above finished ground on the side away from the pool. Gates and doors must self-close and self-latch. A release below 54 inches above the bottom of the gate must be on the pool side. The gate must positively close and latch when released 6 inches from the gatepost. Existing barriers may not be changed to reduce their effectiveness. A spa or hot tub with an ASTM F 1346 safety cover has that section’s exception. The separate pool-and-spa construction standards below also apply.
MATERIAL AND CONSTRUCTION LIMITS
• Wood and Vinyl/PVC: The ordinary fence article does not expressly prohibit wood or vinyl/PVC as general material classes. It does prohibit wood slats tied with wire and similar materials before front building lines on residentially zoned or occupied property. Other construction, height, location and applicable historic-design conditions still govern the design.
• Chain-link and all street frontages: Chain-link, wire, wire mesh, plastic mesh, wood slats tied with wire and similar materials are prohibited in front of the front building line on every street frontage of a residentially zoned or residentially occupied lot. This includes all frontages of corner, through and multiple-frontage lots, unlike the addressed-frontage height rule. The ordinary article does not impose that particular material ban on an interior side or rear fence.
• Other prohibited materials and orientation: Paper, cloth, canvas, bamboo, chicken-coop wire and similar materials may not be used. A fence made solely of single or double wire is prohibited. All framing members and support posts must face toward the interior of the property of the person erecting the fence.
• Barbed and electric fencing: Barbed wire and similar materials are prohibited on residentially zoned or residentially occupied lots. The fence itself may not be energized. A separate energized wire may be installed only in compliance with the National Electrical Code inside an area enclosed and secure from the public, at least 18 inches from the enclosure and 18 inches from every property line. Underground wire installed in compliance with the city Building Code and National Electrical Code has the ordinance’s stated exception. That exception is relevant to underground pet-containment systems; it is not permission to energize an ordinary boundary fence.
• Walls, repair and trash enclosures: Fences and retaining walls must remain structurally sound and in good repair. All outside storage areas for trash/recyclables must be screened. A trash dumpster needs a sightproof fence complementing the principal building, or a wall of similar material, at least 6 feet high, with latching gates of similar or complementary material completely enclosing it. This dumpster requirement is distinct from merely keeping an individual rolling bin on the property.
• Pool construction and covers: The adopted 2021 International Swimming Pool and Spa Code requires at least a 4-foot construction fence around an in-ground pool/spa site from the start of excavation until the permanent barrier is complete. Under its Section 305 cover exception, a powered ASTM F 1346 pool safety cover or a lockable ASTM F 1346 spa/hot-tub safety cover removes the specified Section 305.2–305.7 barrier requirements. That construction-code exception does not itself erase the separate Property Maintenance Code duty described above; the Building Commissioner administers the applicable combined requirements.
• Pool barrier height, ground and openings: The pool/spa construction barrier must reach at least 48 inches above outside grade around its entire perimeter and for the 3-foot horizontal area outside. Bottom clearance is at most 2 inches over nonsolid ground, such as grass or gravel, or 4 inches over a solid surface. A barrier mounted on the pool/spa wall may have no more than a 4-inch gap above that wall. Openings may not pass a 4-inch sphere. Solid barriers may not provide handholds/footholds other than normal construction tolerances and tooled masonry joints. Equipment outside the barrier, including pumps, filters and heaters, must be at least 36 inches away.
• Pool rails, chain-link and diagonal openings: If the tops of horizontal members are less than 45 inches apart, put those members on the pool side and limit vertical-member gaps and decorative cutouts to 1¾ inches. If horizontal-member tops are at least 45 inches apart, vertical gaps may be up to 4 inches, but cutouts remain limited to 1¾ inches. Chain-link openings may not exceed 1¾ inches; slats fastened at top and bottom may reduce larger openings to that maximum. Diagonal-member openings are limited to 1¾ inches and their angle to 45 degrees from vertical.
• Mesh pool fences: Non-chain-link mesh follows the manufacturer’s instructions. Its bottom begins no more than 1 inch above the installed surface, cannot be lifted to more than a 4-inch clearance, and must prevent a 4-inch sphere passing under a panel. Each section attaches at least 45 inches above grade, using a device with the specified safety-hook-equivalent security. Hinged gates meet the gate rules; patio post sleeves must be nonconductive. Mesh may not be mounted on an onground residential pool. Its inside face must be at least 20 inches from the nearest water edge.
• Pool gates and latches: Doors/gates must accommodate a lock. Pedestrian gates open outward, away from the pool, self-close and self-latch. Service/utility gates stay locked when unused. A double/multiple gate has at least one leaf secured in place and the adjoining leaf secured by a self-latch. At residential pools, a non-self-locking release accessible outside must be at least 54 inches above finished floor/ground; self-locking controls/releases may be no higher than 54 inches. Where the only release is pool-side, it must be at least 3 inches below the top of the gate. Openings within 18 inches of an inside release must be no larger than ½ inch.
• A dwelling wall as pool barrier: Where doors, gates or low operable windows in a wall give direct pool access, the code provides protective alternatives. The alarm option uses a listed/labeled UL 2017 water-hazard entrance alarm on the doors/gates and operable windows with sills below 48 inches above the indoor finished floor, including their screens. In dwellings not required to be Accessible units, Type A units or Type B units, the operable parts of alarm-deactivation switches are at least 54 inches above the finished floor. In dwellings required to be Accessible, Type A or Type B units, those operable parts are 48–54 inches above the finished floor. Structures other than dwellings also use the stated 48–54-inch finished-floor range. A listed/labeled ASTM F 1346 safety cover or approved protection giving at least equivalent protection is another stated option. A wall with an ordinary unprotected door is not sufficient.
• Onground pool walls and natural barriers: A pool wall alone may form the barrier only where its bottom is on grade, its top is at least 48 inches above grade around the whole pool, it meets Section 305.2 and the manufacturer allows that use. Where a barrier is mounted on the wall, the top of the combined wall and barrier must be at least 48 inches above grade around the entire pool perimeter; both wall and barrier must comply with Section 305.2, and the barrier follows manufacturer installation instructions. Access ladders/steps must be securable, lockable or removable unless separately enclosed; their removal/securing may leave no opening passing a 4-inch sphere. Where a pool abuts natural water, no barrier is required between it and the shoreline only if no public shoreline access is allowed and the barrier extends at least 18 inches beyond the water edge. Natural topography requires governing-body approval and protection at least equivalent to the specified barriers.
• Tree-protection fencing: For projects subject to tree protection, the Kirkwood Tree Manual establishes a protected zone at least 10 feet from the exterior of the trunk. Enclose the entire zone throughout the project; no excavation, spoil/equipment storage, parking, equipment operation, grading or other disturbance is allowed inside. Use 3-foot green mesh on 5-foot heavy-duty green steel T-posts driven at least 18 inches. Posts should be no more than 8 feet apart. Weatherproof signs at least 8½ by 11 inches must read “WARNING – TREE PROTECTION ZONE,” have no holes through the paper and be displayed at 20-foot intervals visible from all directions. Approved ground-level concrete post bases may be used on retained paving. In tree lawns along public ways, enclose the planting strip and yard while leaving streets/sidewalks open.
• Significant trees, clearcutting and public trees: A significant tree is at least 6 inches in diameter at 4½ feet above ground, in fair or better condition, excluding invasive/undesirable species. A heritage tree is a significant tree at least 18 inches in diameter, or a smaller exceptional/historic tree designated by the Urban Forester. Removing at least 4,500 square feet of canopy from a parcel within 24 months is clearcutting; qualifying invasive, undesirable, storm-damaged or less-than-fair trees are excluded only with evidence supplied in advance. Clearcutting requires a Tree Clearing Permit and approved plan/study. Public-tree pruning/removal outside owner clearance obligations requires Urban Forester permission; a maintenance permit lasts 30 days and a certified arborist is required unless waived. A nonhazardous public-tree removal request goes through Urban Forestry Commission review and the Urban Forester’s final decision; approval may be conditioned on an approved replacement tree at least 2 inches in caliper or the stated replanting fee. A denied application does not authorize removal.
• Tree fees and required replacement: Clearcut permit fees are $500 per significant tree and $1,000 per heritage tree in fair or better condition proposed for removal; unpermitted clearcutting carries a $2-per-square-foot canopy fee. For projects subject to the tree-development provisions, single-family lots need 35-percent canopy coverage; preserved heritage canopy receives 150-percent credit. New large/medium/small trees count 750/500/250 square feet; screening trees count 25 square feet each, up to 350 square feet. Replacement frontage trees are provided at least one per 50 feet of frontage, approximately 5–10 feet from public right-of-way and at least 25 feet from its intersection at a corner. Planting is at least 5 feet from a property line and 10 feet from a utility-easement center unless Forestry approves otherwise. Canopy shortfall replanting fees are $1.33 per square foot. Damage requiring removal of a protected tree requires an updated study/map and replacement or a $500-per-adjusted-diameter-inch replanting fee. Trees credited for coverage must meet the species/health requirements; existing trees must be live, healthy, over 6 inches in diameter and in good/fair condition. New deciduous trees are at least 2 inches in caliper and evergreens at least 8 feet high. A required plan maps work, removals and protection; the arborist study appraises public trees, on-site trees over 6 inches and adjacent trees within 10 feet of the property line, with numbered trees and canopy maps. These are conditional tree-development duties, not a charge on every fence.
• Temporary protection by public ways: Excavation in or adjoining a public street, sidewalk, alley or public place needs a substantial fence/barricade at least 3 feet high or other permit-specified protection. At night, warning lights are required: one for an obstruction no longer than 10 feet, two if over 10 but under 50 feet, and an additional light for each further 50 feet or part. A pedestrian detour around sidewalk construction must be at least 3 feet wide, with a continuous barrier where adjacent to a vehicle lane. These are work-site protections, not ordinary permanent-fence dimensions.
• Properties using onsite wastewater: If a property actually uses onsite wastewater, applicable state onsite requirements and any lawfully applicable stricter local health requirements remain separate from the city fence permit. The state acreage exclusions and any local health requirements depend on their actual statutory conditions and governing program; no local waiver is implied. For a sewage lagoon subject to 19 CSR 20-3.060(6)(D)15, complete the protective fence before dwelling occupancy, with a height of at least 4 feet. Welded, woven or chain-link wire must be 14 gauge or heavier; cattle or hog panels with T-line posts are a stated alternative. Pressure-treated wood or galvanized/painted steel posts must be driven, tamped or set in concrete. Line posts must be no more than 10 feet apart, corners must be braced, and the fence must have no bottom gaps. A properly hinged gate must be at least 4 feet high, comparably constructed and effectively latched. City approval does not waive these duties.
• Lagoon position and recommendations: The fence may be no closer to the water’s edge than the berm center, measured at a 3-foot operating water depth; three feet is water depth, not a horizontal fence setback. The rule recommends line-post depth of 18 inches, corner-post depth of 24 inches, a fence no more than 30 feet from the water edge and a 36–48-inch gate width. Those recommendations are distinct from the mandatory height, spacing, bracing, bottom closure, gate and before-occupancy requirements.
PRIVATE RESTRICTIONS
Recorded covenants, subdivision restrictions, homeowners-association architectural rules, private easements and enforceable boundary or maintenance agreements may add obligations. The instrument’s terms and applicable Missouri law determine those rights; municipal approval does not waive them.
A permit does not establish a boundary, ownership of a shared fence, an adjoining owner’s contribution or a right to interfere with an easement. The age or location of an existing fence alone does not settle title. Public partition-fence duties remain separate from private agreements.
REVIEW AND ENFORCEMENT CONTEXT
Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:
• Permit and property review: Construction/reconstruction permits, replacement conformity, designated-property Landmarks approval and separately triggered grading, tree or floodplain review.
• Placement and visibility: Street and sidewalk clearances, corner/through-lot frontage differences, drainage obstruction, hydrant access and recorded rights.
• Construction and maintenance: Restricted materials, inward-facing supports, pool barriers/gates, tree-protection fencing and unsafe or deteriorated enclosures.
• Private matters: Boundary, covenant, ownership, easement and contribution disputes remain separate from city code enforcement.
USING THIS INFORMATION
This page provides general orientation on how residential fence rules are structured and applied within the City of Kirkwood, Missouri. Updated November 2026.
In addition to local fence rules, certain Missouri laws apply statewide. See Statewide Fence Laws in Missouri.
It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with the identified municipality, including its actual municipal or county class, charter, adopted program or special district, and each function’s verified territory, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Missouri law. Applicable requirements depend on the property’s actual facts and the respective authority of the identified offices. Private agreements and recorded rights remain separate from government approvals. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern.