FENCE RULES – OVERLAND (CITY), MISSOURI

OVERVIEW

This page covers residential fences within the incorporated City of Overland, Missouri, in St. Louis County. A mailing address outside the city does not bring property within its ordinary fence and construction jurisdiction.

Overland requires a permit for fences and screen plantings, with a published $35 fee and different survey requirements for new and replacement fences. Material matters: masonry, wood and vinyl have a six-foot limit, while chain-link has separate coating and district branches. Front yards generally allow only very low decorative fences or qualifying screen planting. Corner and through lots, parallel adjoining fences and water flow have their own conditions. Pool barriers follow the city’s adopted construction codes, and dangerous-animal enclosures have additional requirements. Replacing half of a nonconforming fence triggers current compliance. Updated November 2026.

Quick questionOverland answer
Permit or approvalA permit is required before erecting a fence or screen planting. The published fee is $35; other site approvals remain separate.
Typical fence heightMasonry, wood and vinyl: 6 feet. Uncoated chain-link: 4 feet; coated chain-link has separate district limits. Front decorative fences: 18 inches.
Placement & property linesSide/rear lines may be used subject to applicable rights, drainage and parallel-fence conditions. Front, corner and through lots have separate restrictions.
Common fence materialsWood: planed wood recognized. Vinyl/PVC: vinyl recognized. Chain-link: recognized with coating-, height- and district-specific limits.
Important local conditionsFence rules may be further affected by front yards, corner or through lots, adjoining fences, natural drainage, pools, dangerous animals, floodplain conditions, major land disturbance and recorded restrictions.
Official local resourceOverland fence permit instructions and application

The table summarizes ordinary rules. The sections below preserve the conditions, exceptions and site-specific branches that determine how each requirement applies.

GOVERNANCE

Overland is a third-class city. The City Council adopts zoning and construction requirements within city limits. The Community Development Director or designee administers fence permits and the stated interpretation and approval functions. The city adopts its own 2015 International Building Code, International Residential Code and International Property Maintenance Code, with local amendments. The residential code refers pool and spa design/construction to the 2015 International Swimming Pool and Spa Code. These municipal adoptions operate separately from the county’s function-specific rules.

The Building Commissioner administers the mapped floodplain program. Major land disturbance has a separate city adoption of St. Louis County Chapter 1114. The city’s nuisance authority expressly extends one-half mile beyond city limits; that provision does not extend every zoning, construction or fence specification beyond the city. Private title, easement and covenant matters remain separate from these public functions.

PERMIT AND APPROVAL REQUIREMENTS

• Fence and screen-planting permit: Section 400.360’s fence standards require a permit before erection or construction. The application to Community Development identifies dimensions, location and materials. The current packet requires two copies of a scaled site plan, owner/contractor information and applicant identification. The published fee is $35.

• Survey and inspections: A new fence requires a boundary survey stamped and sealed by a registered surveyor. A replacement fence or screen planting does not require one unless the Director requires it. The owner/applicant schedules the post-hole/footing inspection and final inspection. Current instructions place posts at least 30 inches below common grade in wet-mixed concrete.

• Replacement and nonconforming fences: A legally installed nonconforming fence may remain structurally sound and maintained. Replacement of 50 percent requires compliance with current fence standards. The existing fence does not establish a right to enlarge or replace it unchanged. The local residential-code amendment deletes R105.2 without substitution, so its former model fence exemption is not an independent permit waiver.

• Height approvals: Exceeding the listed fence/screen limits requires Planning and Zoning Commission site-plan approval in C-1, C-2, M-1, PD-R, PD-C, PD-M and PD-MxD, or a Board of Adjustment variance elsewhere. Approval is distinct from the ordinary permit.

• Mapped floodplain development: Construction and other development in the city’s mapped A and AE flood-hazard areas require a separate floodplain permit administered by the Building Commissioner. Flood-resistant construction, appropriate anchorage and drainage apply within their actual development scope; these are not floor-elevation requirements for every fence in the city.

• Major land disturbance: The city adopts county Chapter 1114 only as it pertains to major land disturbance: at least one acre, or a smaller part of a development ultimately disturbing at least one acre. This separate permit program does not make every small fence project subject to all county ordinary-land-disturbance provisions.

• Construction-site protection: For work governed by the residential code, structures open to unauthorized entry during construction require perimeter fencing and signs as directed by the Code Official. Where site grading, excavation or demolition occurs during or incident to covered construction, alteration or demolition, a Missouri-licensed land surveyor must demarcate each property corner before the permitted work begins; the stakes/devices remain for the work’s duration. The site plan must give sufficient grading/stormwater detail for code review.

• Residential-code application and inspection conditions: Under the residential-code amendments, a rejected application is abandoned if required information/corrections are not supplied within 30 days. Extra inspections or reinspections can be required for noncompliance, work not ready or inaccessible work, with applicable fees. No portion of a fee is refunded upon permit revocation or suspension, discontinuance or abandonment of the work.

• Pools and separate rights: Pool construction, its required enclosure and associated electrical work remain subject to the applicable construction permits and inspections. A fence permit does not authorize occupying a street right-of-way, interfering with utilities or disregarding recorded access rights.

FENCE PLACEMENT RULES

• Front yards: A front-yard fence is prohibited except a decorative fence at most 18 inches high and at least two feet from the front property line. Front screen planting may be at most four feet high and must remain at least ten feet from a public road or sidewalk.

• Side, rear, corner and through lots: A side/rear fence may extend to the property line subject to applicable rights and the parallel-fence conditions. On a corner or through lot, the fence may extend from the principal structure’s exterior wall line containing the primary entrance/exit while remaining at least five feet from the property line. The Director determines the applicable wall-line interpretation.

• Parallel adjoining fences: A new parallel fence abutting an existing fence requires removal of the existing fence with its owner’s permission, or at least two feet of separation and an access opening/gate for maintenance. Permission to remove the neighboring fence is separate from a municipal permit.

• Water flow and easements: Fences and screens may not impede or divert natural water flow unless the Director’s investigation finds no damage to adjoining property and improved drainage. Utility, drainage and access easements retain their actual location, scope and access rights; the fence rules do not establish a universal setback from every easement.

• Development screening: Section 400.450’s parking/loading and district-edge screening applies to its stated development conditions, including non-one/two-family district edges adjoining residential property. It can require continuous six- to eight-foot solid screening. Within 15 feet of a right-of-way, the specified screening is at most 3.5 feet; hedge/wall/berm treatment within ten feet of driveways is limited to three feet. These are not automatic requirements for every ordinary residential lot line.

• Boundaries and survey markers: A fence location must respect the actual boundary and recorded rights. Missouri Section 60.355 prohibits knowingly moving, removing, defacing or destroying the listed public-land-survey corners, property markers, benchmarks and horizontal-control monuments, except by a registered land surveyor. It provides a class B misdemeanor classification, monument-restoration liability and the affected owner’s reasonable surveying-cost and attorney-fee remedy. A permit or utility mark does not determine a property boundary.

• Fence-post excavation notice: Missouri’s underground-facility law covers private-property excavation, including hand digging, augering, boring and driving. Except for its limited statutory exclusions, notice through Missouri 811 is required at least two working days and no more than ten working days before the expected start. The period starts at midnight following receipt; Saturdays, Sundays and state or federal legal holidays are excluded. Notice identifies the excavator and responsible person, contact details, expected start, depth, excavation type, trenchless work or explosives where applicable, and sufficient site/location information. The limited tillage and temporary-marker exclusions do not exempt structural post holes.

• Operator responses and second notice: Participating operators ordinarily respond within two working days unless an extended start is agreed. Work cannot begin before the scheduled date unless all facilities have been confirmed located. Either side can request a marking-clarification meeting within two working days; trenchless work also triggers available depth information. If an operator fails to respond to proper original notice, the excavator gives the prescribed second notice before starting. The operator then has two hours to mark or contact the excavator with its marking time. A second notice by 2 p.m. requires marking that working day; later notice requires marking by 10 a.m. the next working day. Excavation may begin only under the statute’s failure-to-mark-or-contact conditions, with required care continuing.

• Notice life and markings: The notice expires at 11:59 p.m. 21 consecutive calendar days from the work start date. Work can continue within the notified area while the notice and visible markings remain valid. Failure to begin within the stated ten-working-day period requires a relocate request before beginning. Unusable marks require a remark request with the original timing. Reasonable care to preserve marks remains required; failure of care or unnecessary repeat marking can create reasonable remarking-cost liability. Separately owned private lines are not a promise of universal locating service.

• Care near underground facilities: The ordinary approximate-location strip is the facility width plus two feet on each side; stated unusual conditions can require a wider designated area. Before work, the excavator determines best practices for confirming horizontal and vertical location in the actual site conditions, using hand or soft digging when possible. An incorrectly located or unmarked facility must be reported through the center; the operator must contact the excavator or correct the location within two hours. Notice compliance does not remove careful-and-prudent excavation duties or grant land-entry rights.

• Damage, emergencies and highway excavation: Facility damage, dislocation or disturbance, including trace wires, encasements and protective stakes, must be reported to the notification center. Pipeline contact/damage causing a hazardous-liquid or gas release requires an immediate 911 call. Damage cannot be concealed or repaired without the facility owner’s authorization. The narrow temporary sewer-emergency repair allowance after notice does not remove reporting. A genuine excavation emergency permits necessary work with reasonable precautions and notice as soon as practical; the operator must mark or contact within two hours and state its marking time if unable to mark then. Excavation in a state highway or its right-of-way separately requires the commission’s permit, subject to the railroad-right-of-way exception.

• Conditional division-fence rights: Missouri’s general and local-option partition-fence laws are alternative systems with their own livestock, allocation, notice, contribution and repair/removal conditions. The local-option system requires the statutory county election and adoption order and excludes counties with all or partial open range. These laws are not a rule that every neighbor pays half of an ordinary yard fence. General-law repair entry concerns repair of the owner’s division-fence portion, not a general access corridor. Removal consent and the separate cultivated-field notice/damage provisions retain their own conditions. Government approval does not settle those rights.

FENCE HEIGHT AND VISIBILITY RULES

• Masonry, wood and vinyl: The listed maximum for these materials is six feet. It is not a single limit for every possible fence material or special enclosure.

• Chain-link and tennis courts: Uncoated chain-link is limited to four feet. Vinyl-coated chain-link is generally five feet, with six feet in C-1, C-2, M-1, PD-R, PD-C, PD-M and PD-MxD. Chain-link immediately around tennis courts can be 12 feet.

• Screen planting and front branches: Screen planting is generally limited to six feet, with the separate side/rear development-screening branch above. Front decorative fences and front screen plantings retain their lower limits and street separations.

• Commercial or industrial sight triangles: Section 400.290(F)’s 30-foot sight triangle applies to new commercial or industrial development. It is not a separate citywide residential-yard triangle. Ordinary homes remain subject to the front, corner/through-lot and other applicable placement conditions.

• Pool barrier height: The adopted pool-barrier framework generally requires at least 48 inches, measured from the outside grade with the specified perimeter/grade conditions. Its construction, gate and alternative-barrier conditions are below; the ordinary yard-fence limits alone do not establish a compliant pool enclosure.

MATERIAL AND CONSTRUCTION LIMITS

• Permitted and prohibited materials: The code recognizes decorative brick/stone, textured or pigmented concrete, planed wood, vinyl, chain-link including vinyl-coated chain-link, wrought iron and steel. Screen plantings consist of hedges or thick shrub growth, with larger vegetation/trees only where the development-screening provision expressly specifies them. Cloth, canvas, chicken wire and impermanent materials are prohibited, as are stockade fences in all districts. Sharp-pointed fences, including barbed wire, razor wire, concertina wire and spikes, are prohibited.

• Finished face and supports: The finished or good side faces outward and the rough side inward. Support posts and horizontal/vertical members must be screened from neighboring properties and the public as the Director finds applicable. The Director’s stated interpretation authority remains.

• Electric fences: The local provision prohibits electric fences with stated exceptions for “battery-charged fence” and fences buried/underground or invisible to the extent permitted by Section 67.301. The state electric-security program concerns its defined nonresidential security installations; it is not a general residential electric-fence permission. Community Development applies the local exception wording to the proposed installation.

• Maintenance: Fences must remain in good repair with paint/coating against decay, rot and rust; screen planting must be trimmed and free of weeds/debris. The adopted property-maintenance code requires fences and walls structurally sound and in good repair. Protective treatment includes the actual exceptions for decay-resistant wood and surfaces designed to stabilize by oxidation. Nuisance controls also address erosion/siltation, stagnant pools, animal conditions and debris.

• Pool covers and barrier scope: The 2015 pool code covers outdoor pools/spas and indoor swimming pools. Its Section 305.1 exceptions include a lockable ASTM F1346 spa/hot-tub safety cover and a powered ASTM F1346 swimming-pool cover. Cover categories and the independent property-maintenance duties below remain distinct.

• Pool height, ground gaps and openings: Barriers must be at least 48 inches above outside grade around the entire perimeter and for three feet horizontally outside. Bottom clearance is at most two inches over nonsolid grade or four inches over a solid surface. A barrier mounted above a pool/spa top has at most a four-inch gap. Openings cannot pass a four-inch sphere. Solid barriers have no climbing handholds/footholds except normal masonry tolerances and joints.

• Mesh pool barriers: Mesh must follow manufacturer instructions, with the bottom at most one inch from the surface. Panels cannot lift more than four inches or admit a four-inch sphere underneath; specified solid-surface gaps are at most four inches. Attachments are at least 45 inches above grade. Where a hinged gate is used with a mesh fence, it must comply with the pool gate requirements; deck sleeves must be nonconductive. Mesh fences cannot be installed on top of on-ground residential pools.

• Pool-barrier members and clear space: Where horizontal members are less than 45 inches apart, they belong on the pool side; vertical gaps and decorative cutouts are at most 1¾ inches. With horizontals at least 45 inches apart, vertical gaps can be at most four inches, while cutouts remain at most 1¾ inches. Chain-link openings are at most 1¾ inches; slats used to reduce openings to that size must be fastened at both the top and bottom. Diagonal openings are at most 1¾ inches and at most 45 degrees from vertical. A 36-inch outside clear zone separates climbable permanent equipment/structures, and the pool-side barrier is at least 20 inches from the water edge.

• Pool gates and latch releases: Gates must accommodate locking devices. Pedestrian gates open away from the pool and self-close/self-latch; service/utility gates are locked when unused. With double gates, one leaf is secured and the adjacent leaf has the compliant latch, with no opening over ½ inch within 18 inches of its release. Under the adopted pool code, a latch release less than 54 inches above grade belongs on the pool side at least three inches below the top, with no opening over ½ inch within 18 inches of the release.

• A building wall as a pool barrier: Access doors/screens and operable low windows with sills below 48 inches above the interior floor need the specified UL 2017 audible alarm. Alarm deactivation is generally at least 54 inches high; the accessible-unit branch is 48–54 inches. Alternatives include the stated ASTM F1346 cover or approved equivalent protection, such as self-closing/self-latching doors. This wall alternative is distinct from the powered-pool-cover exception.

• On-ground pools and natural boundaries: A qualifying on-ground pool wall or wall/top-mounted barrier provides at least 48 inches around the entire perimeter, complies with the barrier rules and is permitted/installed as the manufacturer requires. Steps or ladders must be capable of being secured, locked or removed to prevent access unless separately enclosed by a compliant barrier; resulting openings cannot pass a four-inch sphere. A natural-water boundary requires public shoreline access to be prohibited and the barrier to extend at least 18 inches beyond the water edge. Approved natural topography must provide equivalent protection.

• Existing private pools, hot tubs and spas: The independent property-maintenance rule covers private pools, hot tubs and spas containing more than 24 inches of water. It requires a complete enclosure at least 48 inches above outside finished ground, self-closing/self-latching gates and doors, and positive gate closure from six inches open. Existing enclosures cannot be removed, replaced or changed to reduce their effectiveness. This rule’s ASTM F1346 cover exception is for spas/hot tubs, not every pool. Its separate maintenance duties remain alongside the pool-code construction and latch rules.

• Ordinary dogs and livestock housing: Livestock/poultry cannot be housed or confined within 150 feet of a single-family dwelling on an adjoining lot; the specified animals cannot run at large. A dog is restrained by a controlled leash, an inescapable vehicle, or the owner’s structure/fenced yard, including an invisible fence from which it cannot escape. Tethering outside an inescapable structure/yard is not restraint.

• Dangerous-animal confinement: A dangerous animal requires secure indoor confinement or a locked pen/kennel/structure at least five by ten feet, with a secure top attached on all sides and a secure bottom or sides embedded at least 12 inches. Children must be excluded, adequate shelter provided and zoning/building requirements met. The enclosure ordinarily houses one animal, except a mother with offspring under three months. Signs, cleanliness and ventilation are required. These are dangerous-animal controls, not a minimum size for every pet yard.

• Livestock at large: Section 270.010 prohibits an owner from permitting horses, mules, asses, cattle, swine, sheep or goats to run at large outside the owner’s enclosure. A person may restrain such stock, and an officer with police powers must do so on the stated view/notice conditions. Written notice to a known owner is due within three days, stating feeding/keeping compensation and claimed damages. The owner owes reasonable taking-up/keeping/feeding compensation and actual damage. For a public-road/highway accident, the owner has the statutory defense of proving the animals escaped through no fault or negligence of the owner. Unknown ownership or failure to compensate after notice leads to the stray-law process.

• Covered household sewage lagoons: Missouri’s onsite sewage regime includes single-family lagoons and excludes systems regulated under Chapter 644. Section 701.031 excludes a qualifying single-family residential lot of at least three acres, or the separate residential-lot branch of at least ten acres with no single-family onsite system within 360 feet of another onsite system and no more than one residence per ten acres in the aggregate. The exclusions do not cover the specified lots adjacent to lakes operated by the Corps of Engineers or a public utility. All system points must be more than ten feet from adjoining lines, without effluent trespass, surface/groundwater contamination or a scientifically determined nuisance. Construction, operation, major modification and major repair otherwise follow the statutory/rule regime. More restrictive local standards remain possible; acreage alone is not permission to construct a lagoon.

• Covered lagoon fence construction: Where 19 CSR 20-3.060(6)(D)15 applies, the pond must have a fence at least four feet high, complete before dwelling occupancy. Welded, woven or chain-link material must use wire no smaller than 14 gauge; cattle/hog panels may substitute with tee-post line posts. Posts must be pressure-treated wood or galvanized/painted steel, driven, tamped or concrete-set. Line posts must be no more than ten feet apart, corner posts properly braced, and sound construction must leave no bottom gaps. The fence must be no closer to the operating water edge than the berm center, measured at the three-foot operating water level. A properly hinged four-foot-high gate of comparable material needs an effective latch.

• Lagoon recommendations and local requirements: The state rule recommends, rather than mandates, line-post depth of 18 inches, corner-post depth of 24 inches, setback no greater than 30 feet from the water edge, and gate width of 36–48 inches. These “should” provisions differ from the mandatory fence, spacing, bracing, gate and occupancy requirements. The state Department of Health and Senior Services administers the statutory standards where local government has not adopted them; an independently adopted local ordinance can impose additional or stricter requirements.

• Licensed family childcare homes: For a licensed family childcare home, the outdoor play area must be on or adjoining the premises and accessible without hazards. Fencing is required where necessary against traffic, water or other hazards. For homes initially licensed after the rule’s effective date, and for new fences at existing facilities, the fence must be at least 42 inches high. Fences must prevent children from crawling/falling through or becoming entrapped.

• Licensed-home pools and animals: Swimming and wading pools at licensed family childcare homes must be fenced to prevent child access. For the rule’s initial-license cohort, the fence must be at least 42 inches with a locked gate. An aboveground pool may instead have that fence around its top and barricaded steps. Hazardous animals must be securely penned where children cannot reach them. These licensed-home rules do not replace other applicable local pool and animal requirements.

PRIVATE RESTRICTIONS

Recorded covenants, subdivision restrictions, homeowners-association architectural rules, private easements and enforceable boundary, maintenance or cost agreements can impose obligations separate from public requirements. Their actual wording and applicable Missouri law determine their reach; there is no universal private fence height or material rule for every property.

Government approval does not determine the property boundary, confer ownership of a shared fence, settle cost allocation or authorize interference with another person’s access. Public statutory partition-fence duties remain separate from private agreements. An existing fence’s age or position alone does not settle title, and a gate does not automatically legalize a fence across an easement.

REVIEW AND ENFORCEMENT CONTEXT

Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:

• Permit and site review: Fence/screen permits, surveys, inspections, replacement compliance and separate floodplain or major-land-disturbance approvals.

• Placement and materials: Front and corner/through-lot location, parallel fences, drainage, height branches, finished faces and prohibited materials.

• Special enclosures and maintenance: Pool barriers/gates, dangerous-animal confinement, livestock housing, covered lagoons, licensed-home enclosures and deteriorated fences.

• Separate private matters: Covenant, ownership, boundary, easement and shared-cost disputes remain distinct from municipal review and nuisance enforcement.

USING THIS INFORMATION

This page provides general orientation on how residential fence rules are structured and applied within the City of Overland, Missouri. Updated November 2026.

In addition to local fence rules, certain Missouri laws apply statewide. See Statewide Fence Laws in Missouri.

It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with the identified municipality, including its actual municipal or county class, charter, adopted program or special district, and each function’s verified territory, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Missouri law. Applicable requirements depend on the property’s actual facts and the respective authority of the identified offices. Private agreements and recorded rights remain separate from government approvals. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern.