FENCE RULES – PLATTE (COUNTY), MISSOURI

OVERVIEW

This page covers residential property in unincorporated Platte County, Missouri, including homes on rural acreage. Incorporated municipalities administer their own land-use and building requirements; a Platte County mailing address alone does not establish county permit jurisdiction.

Platte County regulates ordinary affixed fence construction through its zoning permit provisions and sets a six-foot maximum in its agricultural and residential districts. Several residential districts also require fences to meet the front-yard setback, while other listed districts allow front-yard encroachment. Corner visibility, retaining walls and outward-facing fence surfaces add design rules. Pool barriers, onsite wastewater lagoons, stream buffers, mapped floodplain work and county road rights can substantially change the project. Ordinary nonstructural repair has a separate permit exception, but reconstruction is not automatically repair. Updated November 2026.

Quick questionPlatte County answer
Permit or approvalConstruction or reconstruction of a structure affixed to the ground falls under the county permit rule. Ordinary nonstructural repairs are excepted; portable designs and disputed repair classifications depend on the work.
Typical fence heightSix feet maximum in the listed agricultural and residential districts. Corner visibility and retaining-wall combinations can be more restrictive; protective barriers have separate minimums.
Placement & property linesListed residential districts require front-yard setbacks, generally 25–35 feet depending on district and plat date. Other listed districts allow front-yard encroachment. Boundary, street and easement geometry still controls.
Common fence materialsWood: no separate ordinary-yard classification communicated. Vinyl/PVC: no separate ordinary-yard classification communicated. Chain-link: no separate ordinary-yard classification communicated; pool and lagoon barriers have specific standards.
Important local conditionsFence rules may be further affected by corner sightlines, retaining walls, required screens, pools, farm animals, stream buffers, floodplain, road rights, onsite systems, utilities and recorded restrictions.
Official local resourcePlatte County Planning and Zoning permit information

The sections below distinguish ordinary yard-fence rules from conditions tied to the property’s district, approved plans, water features or residential use.

GOVERNANCE

Platte County is a first-class statutory county. The County Commission adopts county orders. Planning and Zoning, including the Director and Codes Coordinator, administers county zoning, construction and floodplain requirements within the applicable county territory. Municipal approvals remain separate for property inside an incorporated municipality.

The county identifies the 2018 International Residential Code and International Swimming Pool and Spa Code, as amended, along with other adopted construction codes. Its residential-code adoption deletes Section R105.2 and directs exempt-work matters to the amended Zoning Order. Consequently, an unamended model-code fence exemption does not establish a county exemption. Public Works administers county right-of-way work, and the Platte County Health Department Sanitarian administers local onsite wastewater requirements.

PERMIT AND APPROVAL REQUIREMENTS

• Affixed fences and ordinary repairs: Section 400.750C of the county Zoning Order requires a permit for construction, reconstruction, renovation, remodeling, moving, demolition, structural alteration or change of use of a building or structure affixed to the ground, and for covered changes in bulk or nonbuilding use. An ordinary ground-affixed fence construction or reconstruction project falls within that rule. Ordinary nonstructural repairs are excepted. Replacing posts or rebuilding a run is not automatically that exception. A portable enclosure or unusual repair depends on its attachment and scope.

• Application and timing: The application identifies the legal description, owner and applicant, use and work, with applicable site, erosion and elevation plans and health, sewer, water or road approvals. The county accepts portal applications and states that complete building applications are acted on within five working days. Construction does not begin before permit issuance and payment. Work started without a required permit is subject to a doubled fee, except an emergency determined by the official, and may receive a stop-work order.

• Permit duration and revisions: The permit packet requires work to begin within 180 days and not cease for more than 180 days. Changes require approval before work; structural revisions require an engineer’s seal. The packet separately assigns two years to new residential construction and six months to other construction, with limited project-specific extensions. Those project categories do not turn a fence into a new-house permit; the issued permit identifies its applicable term.

• Pools and protective barriers: The county lists the amended 2018 pool code and a $75 pool permit. Its current application calls for a property-line site plan, a licensed surveyor if there is a setback discrepancy, construction and elevation details, applicable structural or gunite details, electrical and equipment schematics, area and value. The signed affidavit must be notarized by final inspection. A surveyor-prepared plan may be required through that review. The pool barrier is a separate safety requirement, not satisfied merely because an ordinary fence is six feet or less.

• Mapped floodplain development: Chapter 410 floodplain requirements apply to the county-jurisdiction numbered and unnumbered A and AE special-flood-hazard areas shown on the April 2, 2015 flood maps and amendments. The Planning and Zoning Director administers a separate permit before construction or other development, including filling, grading, excavation and storage. The application identifies land, use, work, value, floodway or fringe status, base-flood and proposed elevations, plans and signature. Existing easements and covenants are not abolished by floodplain approval.

• Floodway design and review: Until a floodway is designated, proposed development combined with existing and anticipated development in a numbered A or AE zone cannot increase the base-flood surface more than one foot anywhere in the community. In a regulatory floodway, encroachment requires standard engineering hydrologic and hydraulic analysis demonstrating no increase. Covered work uses anchoring, flood-resistant materials and construction methods; altered watercourse capacity must be maintained. Appeals and variances go through the Board of Zoning Adjustment, with Circuit Court review. The agricultural or storage-building variance provisions are not an automatic fence waiver.

• Larger ground disturbance: A project disturbing at least one acre, excluding agriculture, requires the county land-disturbance permit, approved sediment and erosion plan and applicable performance guarantee. Immediate emergency protection, agriculture, federal or state projects and specified mowing, brush-hogging or tree cutting without grading or root removal have exceptions; clearcutting is not included in that vegetation exception. The Director has 30 days for written review; failure to act permits work as filed unless an extension was agreed. Other permits remain separate. Missouri’s construction-stormwater program also covers smaller work within a common development or sale plan cumulatively disturbing at least one acre.

• Erosion controls and restoration: The county land-disturbance permit expires one year after issuance. If work will continue beyond that date, the permittee must reapply to the county for a new permit before the existing permit expires. Required inspections and erosion controls continue during work. Permanent vegetation must achieve 70 percent density over 100 percent of the disturbed area, including restoration of adjoining land disturbed by the permit holder. Controls remain until vegetation is established; temporary controls are removed after permanent stabilization. Separate stream, drainage and stormwater requirements still apply.

• Smaller permitted projects: Under Section 400.535F, disturbance under one acre associated with a structure requiring a building permit must still meet county sediment and erosion requirements. The permit holder maintains lot-specific controls, inspects them at least weekly and after each rainfall, corrects deficiencies immediately and keeps sediment out of storm drains. Large vegetated rural sites with single-family or accessory construction may not need specific controls when disturbance is more than 100 feet from every property line or watercourse; controls are required if sediment leaves the site. Temporary sediment fencing is maintained and promptly repaired or replaced, with deposits removed to preserve capacity; accumulation should not exceed half its height. Waste and tracked debris must be controlled, and disturbed controls reinstalled after utility work. These requirements concern construction protection, not the permanent yard-fence material or height.

• County road corridors: Work impacting an unincorporated county right-of-way requires a Public Works Special Use permit. The county directs Highlands of Weatherby and The Masters applications to Planning and Zoning. Apply at least 30 days before work; completed applications have a review period of up to 31 days. The site information identifies location, dimensions, fences, easements, other features, start and duration. The minimum nonrefundable fee is $75, with applicable review and inspection charges. A preconstruction inspection accompanies the application, and the owner gives installation and final-inspection notices.

• Onsite wastewater permits: The local onsite wastewater ordinance and attached standards cover construction, installation and modification of systems under 3,000 gallons per day in unincorporated county territory. Submit the soil, site and layout information and fee to the Health Department Sanitarian first. The Sanitarian may issue a written no-permit determination; an owner does not independently assume an acreage exemption. Current local permit and repair requirements remain separate from suspension of the state’s $90 application fee.

• Onsite decisions, inspections and appeals: Within five working days the local process provides approval, a written no-permit determination, denial or proposed modifications. A permit lasts one year and may be renewed for another year by a written request filed with the Sanitarian at least 30 days before expiry; transfers are processed as an application. Give at least 24 hours’ notice before the preburial inspection. Do not operate a malfunctioning system. A written appeal to the Health Officer stating the specific disagreement is due within 45 days of the Sanitarian’s decision; the hearing is held within 30 days of filing, and the Health Officer supplies a written decision within 15 days of the hearing’s conclusion.

• Historic and special-use properties: An ordinary countywide residential historic fence-design approval is not communicated in the county’s published fence provisions. That does not override a designation, approved development plan, special-use condition or recorded restriction on the property. Farm animals and licensed residential uses have their own requirements below.

FENCE PLACEMENT RULES

• Residential front-yard setbacks: Fences and freestanding walls must meet the applicable front-yard setback in R-25, R-15, R-12, R-10, R-7, RTD and RMD. The stated front setbacks are 35 feet in R-25, R-15 and R-12, and 30 feet in R-10, RTD and RMD. In R-7, platted lots recorded after October 17, 2022 have a 25-foot front setback; other R-7 lots have 30 feet. A double-frontage lot must meet the street-front requirement on both streets.

• Street measurement and encroachment districts: The ordinary front-yard measurement begins at the street right-of-way line. Where dedicated right-of-way is less than 50 feet wide, the prescribed starting line is 25 feet from the street-easement centerline. Major thoroughfares use the future right-of-way line in the Major Street Plan. Fences in AG, RE, R-80, R-40, CH and PI may encroach into front-yard setbacks; that permission does not expressly extend to freestanding walls, subject to other applicable restrictions. The provision does not expressly assign PO or CN to either front-yard branch. Ordinary side- and rear-yard building setbacks are not automatically fence setbacks; boundaries, easements and applicable site conditions remain controlling.

• Stream-buffer widths: The county subdivision regulations apply stream buffers to new development and redevelopment in unincorporated territory, except specified previously approved plats, site plans and special-use plans. Buffer widths on each side, measured from the stream centerline, are 50 feet for a 25–40-acre basin, 75 feet for a 40–160-acre basin, 125 feet for a 160–5,000-acre basin and 150 feet for a basin over 5,000 acres. The listed ranges share boundary values; the applicable classification at those exact values belongs to the county’s site review. The separate streamside zone extends 25 feet from the bankfull edge, associated with approximately a two-year rainfall event. These different origins are not interchangeable.

• Stream-buffer exceptions and existing work: The corridor-buffer requirement excludes basins under 25 acres and manmade ditches in street rights-of-way. Specified remnants shorter than 300 feet adjoining existing sewers may be enclosed. Unstable banks and steep slopes may require wider protection. Isolated reductions need evidence that full width is impractical, bank stability addressed, and Planning and Zoning Commission approval. Stream armoring does not itself reduce the buffer; the Director’s limited structure-protection or restoration waiver has Board of Zoning Adjustment appeal. Work at an existing facility cannot move closer to the stream and must address bank stability even where formal buffer designation is not required.

• Uses and maintenance within buffers: Conservation, passive crossings, utilities, flood controls and agriculture have conditional allowances. Streamside planting is native vegetation. Other low-impact riparian uses require the Director’s approval and do not include parking; recreational fields may encroach no more than one-quarter of the buffer. The owner maintains the area unless the county accepts maintenance. A fence proposal within a buffer therefore needs its use and disturbance evaluated rather than an assumed ordinary-yard allowance.

• Easements and drainage: Subdivision provisions generally call for rear or side utility easements at least ten feet wide, with the side-easement alternative perpetual and unobstructed, and storm-drainage easements at least 15 feet wide. Those plat-design dimensions do not establish every historic easement’s width or a universal fence offset. The plat, recorded grant, drainage function and maintenance access control the fence’s relationship to the easement.

• Right-of-way notices and safe work: Covered Special Use work requires written notice to affected utilities at least ten business days in advance, with evidence accompanying the application; the Director receives 24-hour start notice. Owners and occupants within 500 feet receive 48-hour notice, and traffic closures require 72 hours. The five-day facility-relocation notice under Section 229.350 applies where its conditions arise. Overnight excavations need safe covers, barricades, lights or orange safety fencing and adequate passage. Do not obstruct gutters or waterways.

• Right-of-way restoration and responsibility: The permit requires record or as-built drawings and restoration by its specified date, less than 30 days after completion unless extended. Nonutility work requires performance and payment security unless waived, with a six-month maintenance responsibility and hold-harmless provisions. The user pays for damage. These corridor obligations do not grant ownership or authorize a private permanent fence across public road rights.

• Public road rights: For covered noncharter-county roads, Missouri Section 229.150 prohibits willful and knowing obstruction or damage through specified acts, including fencing across or upon the right-of-way, obstructing drainage and planting hedges within road lines. Its specified Natural Resources Conservation Service soil/water-conservation and precision-land-grading exceptions have their own conditions. Road rights are not measured solely by the pavement edge.

• Road-obstruction procedure: The road overseer or county highway engineer may give tracked written notice requiring removal, approved repair or reasonable-cost payment. After 30 days from tracked delivery without compliance, the authority may petition the associate circuit court with a cost estimate. An opportunity for hearing and a granted petition precede entry. Authorized restoration is limited to the necessary work to substantially match adjacent roads or ditches. The statute provides restoration, court and reasonable attorney costs and a tax-collected lien, with an owner-attorney-fee branch when the county does not prevail.

• Survey markers: Missouri Section 60.355 protects the listed public-land-survey corners, boundary markers, benchmarks and horizontal-control monuments from knowing removal, movement, defacement or destruction, with an exception for a registered land surveyor. The statute provides a class B misdemeanor classification, restoration-cost liability and the affected owner’s stated surveying-cost and attorney-fee remedy. A fence permit does not authorize moving a protected marker.

• Excavation notice: Fence-post excavation, including covered hand digging, augering or driving, is subject to Missouri’s underground-facility law. Section 319.026 requires notice to the notification center at least 2 working days, but not more than 10 working days, before the expected start. The statutory period begins at midnight following receipt; Saturdays, Sundays and legal holidays are not working days. Notice identifies the excavator, responsible person, location, expected start, depth and type of excavation, and the other required site/contact information. The notice service is Missouri 811. Utility locating does not establish property boundaries or grant permission to enter another property.

• Responses and an unanswered notice: Under Section 319.030, participating operators ordinarily respond within two working days unless an extension is agreed. Early excavation requires the law’s confirmation that all facilities have been located. If an operator has not responded after a proper original notice, the excavator must give the prescribed second notice before beginning. The operator then has two hours to mark or contact the excavator; a second notice received by 2 p.m. requires marking that working day, and a later notice requires marking by 10 a.m. the next working day. Only the statute’s failure-to-mark-or-contact conditions allow excavation after that process. An unanswered first notice is not immediate permission to dig, and careful work remains required.

• Ticket life and markings: The notice has an operational life ending at 11:59 p.m. 21 consecutive calendar days from the start date of work. Work may continue within the described area while the notice remains valid and markings remain visible. If work cannot begin within ten working days as described in the request, a relocate request is required before starting. Unusable marks require a remark request with the original notice timing. Excavators must reasonably preserve markings; unnecessary repeat marking caused by a failure of care can create cost liability.

• Care near facilities: The statutory approximate-location strip is ordinarily no wider than the facility width plus two feet on each side. When reinforced concrete, multiple adjacent facilities or other specified unusual conditions interfere with locating, the operator designates a wider approximate area to the best of its ability. Before excavation, the excavator determines best practices for confirming horizontal and vertical location in the actual site conditions; hand or soft digging is used when possible. An incorrectly located or unmarked facility must be reported through the notification center, and the operator must respond within two hours by contact or correct locating. The limited exclusions for specified tillage or temporary markers are not a general exemption for structural fence-post holes.

• Damage and emergency work: Damage, dislocation or disturbance of a facility or its protective items, including trace wires, encasements and protective stakes, must be reported to the notification center. Pipeline contact or damage causing a hazardous-liquid or gas release requires an immediate 911 call. The excavator must not conceal damage or attempt repairs without the facility owner’s authorization. Emergency temporary sewer repairs after notification are narrowly allowed to prevent further damage; they do not remove the reporting duty. A genuine excavation emergency permits necessary work with all reasonable precautions to protect facilities and notice as soon as practical. Within two hours of receiving the emergency notice, the operator must mark or contact the excavator with available information and, if unable to mark within that time, state when marking will occur. Separate Missouri Department of Transportation permission applies to excavation in a state highway or its right-of-way under Section 319.025, subject to its railroad-right-of-way exception.

• Division fences: Missouri’s general and local-option partition-fence systems have different contribution, repair and removal conditions. Local option requires the county election and adoption order and has open-range exclusions. The applicable county system determines the contribution, repair and removal rights. Ordinary yard fencing does not create an automatic right to half-cost payment or a ten-foot new-construction entry corridor. Applicable statutory repair-entry rights concern the division fence and the relevant system; private agreements are separate.

• Protected burial grounds: Missouri Sections 214.131–214.132 protect fences and railings around qualifying nonpublic abandoned family or private burial grounds with no interment for at least 25 years. Knowing damage or removal is prohibited. A qualifying landlocked site retains reasonable ingress and egress for usual visits during reasonable hours, with the sheriff or chief county law officer’s stated enforcement role. A perimeter fence does not erase that access.

FENCE HEIGHT AND VISIBILITY RULES

• Agricultural and residential maximum: Section 400.360C sets a six-foot maximum for fences and freestanding walls in AG, RE, R-80, R-40, R-25, R-15, R-12, R-10, R-7, RTD and RMD. AG is expressly included; agricultural zoning does not supply unlimited height. That paragraph does not specify a grade-measurement origin. The separate road-crown sightline rule and retaining-wall combination rule below retain their own measurement conditions.

• Other zoning districts: PO, CN and CH fences have an eight-foot maximum and require a site development plan. PI permits eight feet, or ten feet for special screening or buffering with a setback of at least two-thirds the fence height from the property line and a site plan. These are district-specific alternatives, not residential-district height allowances.

• Corner visibility: On a corner lot with required front and side yards, a fence, wall, sign, structure or plant growth cannot obstruct sightlines between two and six feet above the adjacent roadway crown within the specified triangle. Measure 25 feet along the front and exterior-side lot lines from their intersection and connect the endpoints. This is a visibility restriction within that geometry, not a six-foot permission throughout the triangle.

• Retaining walls and nearby fences: A retaining wall over 30 inches above grade needs a safety barrier, such as a guardrail or qualifying shrubs. A fence, freestanding wall or guardrail atop such a wall cannot exceed four feet. A fence or freestanding wall within three feet of the retaining wall counts as atop it. The wall-and-barrier relationship is separate from the ordinary six-foot yard maximum. Qualifying shrubs reach at least 36 inches with year-round foliage and density acceptable to the Enforcement Officer.

• Pool barrier baseline: The county’s adopted pool-code framework is the amended 2018 International Swimming Pool and Spa Code. Its Section 305 model baseline requires a barrier at least 48 inches above grade measured on the side away from the pool, throughout the perimeter and for three feet horizontally outside. A qualifying lockable ASTM F1346 spa or hot-tub cover, or powered pool safety cover, provides the stated exception to Sections 305.2–305.7. The county’s adopted amendments and approved design govern the pool project; an ordinary yard fence is not automatically a compliant pool barrier.

• Home sewage lagoons: Where the adopted onsite standard applies, the lagoon fence must be at least four feet high and complete before dwelling occupancy. It is located at or landward of the berm center relative to the water edge at the three-foot-deep operating water level. Three feet describes operating water depth, not a horizontal fence setback. The rule recommends a fence setback no greater than 30 feet from the water edge.

• Livestock fencing: Missouri’s lawful livestock-fence standards serve animal-containment and partition-law purposes, rather than setting a yard-fence maximum. Under the general system, Section 272.020 recognizes securely fastened posts and wire or boards at least four feet high, posts firmly set no more than 12 feet apart, mutually agreed by adjoining owners or determined by the associate circuit court, with spacing resisting horses, cattle and similar stock. Local option has its different board, four-barbed-wire and equivalent-fence designs and contribution rules. Their application depends on the county system and use.

• Licensed family childcare homes: The outdoor play area must be on or adjoining the premises and accessible without hazards. Fencing is required where necessary to protect against traffic, water or other hazards. For homes initially licensed after the rule’s effective date and for new fences at existing facilities, the fence is at least 42 inches high. Fences must prevent crawling or falling through and entrapment. Separate pool fencing prevents child access; the rule’s initial-license cohort requires at least 42 inches and a locked gate. An aboveground pool may use that fence around its top with barricaded steps. Hazardous animals must be securely penned inaccessible to children.

• Permitted captive cervids: For deer or other cervids held under the state permit regime, the enclosure and posts reach at least eight feet throughout, with gates meeting the standard and locked and latched. This is a captive-animal enclosure requirement, not a rule for an ordinary garden fence intended to keep wild deer out.

MATERIAL AND CONSTRUCTION LIMITS

• Ordinary yard materials and finished face: Wood: no separate ordinary-yard material classification communicated. Vinyl/PVC: no separate ordinary-yard classification communicated. Chain-link: no separate ordinary-yard classification communicated. The ordinary fence provisions do not communicate a separate metal, barbed-wire or electric-fence material schedule; that is not affirmative approval of every design. The fence face must point toward the exterior of the lot. Protective barriers and required screens have their own construction conditions.

• Retaining-wall construction: Retaining walls in all uses must meet acceptable engineering standards and be terraced whenever possible. Their safety barrier and nearby fence-height conditions described above remain applicable. An unamended model-code retaining-wall permit exemption does not substitute for the county’s zoning and adopted-code requirements.

• Required screens and approved plans: The owner must erect, maintain, repair and replace landscaping and screens required by approved plans, permits, occupancy approvals, subdivisions, special permits, variances or zone changes. A screen volunteered in an application can become a condition of approval. Registered-mail violation notice provides 30 days to correct. A nonresidential edge adjoining residential property has its own six-foot-high, ten-foot-wide screening requirement cutting off a six-foot horizontal sightline while preserving the sight triangle; that is not an automatic screening duty for every homeowner.

• Pool openings and solid surfaces: The 2018 Section 305 baseline limits the bottom gap to two inches over nonsolid grade or four inches over a solid surface. A barrier mounted atop a pool has a maximum four-inch gap to the pool structure. Openings cannot pass a four-inch sphere. Solid barriers cannot have climbable indentations or protrusions other than ordinary construction joints and masonry tolerances. Keep a 36-inch clear zone outside from climbable equipment or structures, and at least 20 inches between the poolside barrier and the water edge.

• Pool rails, chain link and diagonal members: Where horizontal rails are less than 45 inches apart, place them poolside; vertical-member spaces and decorative cutouts cannot exceed 1¾ inches. With rails at least 45 inches apart, vertical spaces may be four inches, while decorative cutouts remain limited to 1¾ inches. Chain-link openings are limited to 1¾ inches; slats fastened at top and bottom may reduce larger openings. Diagonal-member openings cannot exceed 1¾ inches, with diagonal members no more than 45 degrees from vertical. These are pool-barrier conditions, not ordinary-yard chain-link restrictions.

• Pool mesh barriers: The Section 305 mesh design follows manufacturer instructions, with the bottom no more than one inch above the surface or grade and not liftable more than four inches. It cannot allow a four-inch sphere under a panel; the specified solid-surface gap is also limited to four inches. Attachment devices are at least 45 inches above grade. Hinged gates meet the gate provisions, and deck sleeves are nonconductive. Mesh cannot be mounted atop an onground pool.

• Pool gates and releases: Gates must accommodate a lock. Pedestrian gates open outward away from the pool and self-close and self-latch; utility or service gates stay locked when unused. Double or multiple gates need one fixed leaf and an adjacent self-latching leaf, with openings no larger than one-half inch within 18 inches of the release. A release below 54 inches above grade is on the pool side at least three inches below the top, with no opening over one-half inch within 18 inches of the release.

• Dwelling walls and onground pools: Where a dwelling wall forms the pool barrier, direct-access doors and operable windows with sills less than 48 inches above the indoor finished floor need the Section 305 UL 2017 alarm arrangement. In dwellings or structures not required to be Accessible units, Type A units or Type B units, the operable alarm-deactivation parts are at least 54 inches above the finished floor. In dwellings or structures required to be Accessible, Type A or Type B units, those parts are 48–54 inches above the finished floor. A qualifying ASTM F1346 cover or an approved equivalent, such as self-closing and self-latching doors, is an alternative under that section. An onground pool wall may serve as the barrier if its bottom is on grade and its top is at least 48 inches above grade around the entire perimeter, the wall complies with Section 305.2 and the manufacturer permits that use. Where a barrier is mounted on top of the pool wall, the top of the combined wall and barrier must be at least 48 inches above grade around the entire perimeter, and both the wall and top-mounted barrier must comply with Section 305.2. Top-mounted barriers follow the manufacturer’s instructions. Ladders or steps must be secured, locked, removed or enclosed by a compliant barrier, without leaving an opening that passes a four-inch sphere.

• Natural pool boundaries: The Section 305 natural-water-edge alternative requires no public access along that shoreline and a barrier extending at least 18 inches beyond the water edge. A natural topographic feature used as an equivalent barrier requires governing-body approval. Neither alternative is a general exemption for a yard near a pond or steep slope.

• Lagoon wire, posts and gate: The applicable lagoon standard requires welded, woven or chain-link material with wire no smaller than 14 gauge; cattle or hog panels may substitute with tee-post line posts. Posts are pressure-treated wood or galvanized/painted steel, driven, tamped or concrete-set. Line posts are no more than 10 feet apart; corner posts must be properly braced. Sound construction leaves no bottom gaps. A properly hinged, four-foot-high gate of comparable material needs an effective latch. Line-post depth of 18 inches, corner-post depth of 24 inches and gate width of 36–48 inches are recommendations, not mandatory dimensions.

• Lagoon location and effluent: The local standard places the lagoon shoreline at least 75 feet from property lines, increased as needed to keep effluent onsite. Minimum separations include 200 feet to the nearest existing residence, 100 feet to the served residence, 100 feet to potable water or a pump-suction line and 50 feet to a stream, watercourse or lake. Its table lists 15 feet to a swimming pool and 200 feet to an adjoining dwelling. Site requirements and local codes may modify minimum distances. One pond serves one single-family home; lots under three acres are described as not generally suitable, not absolutely prohibited. An effluent outlet is at least 100 feet from a line, or uses the stated 150-foot terraced-swale alternative. Controlled irrigation applies if that approach is unsuccessful or permeable soil is under 12 inches deep.

• Acreage and local onsite authority: State Section 701.031 has a qualifying single-family three-acre exclusion and a ten-acre branch with no single-family residential onsite system within 360 feet of another system and no more than one single-family residence per ten acres in the aggregate. Specified Corps of Engineers or public-utility lake lots are excluded from that relief. Every system point must be more than ten feet from adjoining lines, without effluent trespass, water contamination or a scientifically determined nuisance. Section 701.047 preserves stricter local requirements. In Platte County, the Sanitarian’s written permit or no-permit determination governs the local process; acreage alone is not the owner’s authorization.

• Farm-animal uses: Section 400.325’s special-use provisions cover cattle, horses, goats, sheep, chickens, ducks and rabbits, with AG, RE, R-80 and OSP excluded from that section. In covered districts, the larger livestock category requires five acres including two continuous pasture acres. Covered poultry or rabbits require 15,000 square feet and a rear-yard location; roosters are not allowed on lots under five acres. Covered animals must be fenced under Section 400.360C, with homeowners association approval or covenant proof where applicable and no nuisance. Those use conditions do not eliminate the fence-height rule in an agricultural district.

• Livestock at large: Section 270.010 prohibits owners from permitting horses, mules, donkeys, cattle, swine, sheep or goats to run at large outside their enclosure. Any person may restrain them; an officer with police powers must do so. Written notice to a known owner is due within three days and states feeding/keeping compensation and damages claimed. Reasonable taking-up, keeping and feeding costs and actual damages are provided. For a public-road accident, an owner who proves the animals escaped through no fault or negligence has the statutory defense. Unknown owners or unpaid notified compensation lead to the stray-law process.

• State-park livestock boundaries: For a qualifying boundary beside a state park or historic site, the state participation program addresses livestock or commercial-game intrusion. A written Fencing Request Form and director/designee approval precede participation; a written decision is due within 60 days. A required boundary survey is shared equally. On approval the division supplies construction materials; the owner constructs, and the owner and successors maintain the fence. The fence follows the verified boundary unless a written variance is approved. Construction cannot alter elevations to drain wetlands or impound water on department land. Facility-manager permission governs vehicles, equipment and herbicides affecting park vegetation; limited brush work extends no more than three feet onto park land and overhanging branches may be trimmed at the boundary up to eight feet high. Removal needs written consent except temporary repair. Poisonous-crop land and fencing already required by another law or judgment do not receive the stated participation.

• Captive-animal enclosure construction: Permitted captive-cervid fencing uses woven or high-tensile woven wire no smaller than 12½ gauge, welded wire no smaller than 6 gauge, chain link no smaller than 9 gauge, or wood planks. Vertical-wire/plank spacing is no more than 6½ inches and ground clearance no more than three inches. Stacked fences require at least six-inch overlap and attachment no more than three feet apart, or combination/attachment no more than 12 inches apart. The rule requires clearing woody vegetation under six inches in diameter at breast height for six feet inside and outside on controlled land; post-June 30, 2019 enclosures/additions have the separate all-woody-vegetation clearing condition. Dead trees taller than their distance to the fence must be felled on controlled land. Water crossings, terrain and maintenance must prevent escape and entry. Defined nonnative large cats and bears have a separate permit and federal-standard regime, with its specified exemptions; ordinary pet fencing does not establish authorization to keep them.

PRIVATE RESTRICTIONS

Recorded declarations, homeowners association architectural requirements, easements and boundary or maintenance agreements operate separately from government approvals. More restrictive private covenants and applicable public requirements survive county subdivision or permit approval. Their terms can govern material, height, location, gates and maintenance; a county permit does not approve a violation of those rights.

An access easement can be affected by a fence or gate even without complete blockage, depending on its grant and interference with permitted use, equipment access and maintenance. Providing a gate key is not an automatic resolution. A fence’s age or presence alone does not establish ownership of disputed land. A surveyor’s real-property report disclaiming a boundary survey and construction use is different from a fence-location boundary survey.

REVIEW AND ENFORCEMENT CONTEXT

Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:

• Permit and zoning review: Affixed fence construction, reconstruction, repair classification, district height, front-yard placement, corner visibility, retaining walls and approved screens reviewed through Planning and Zoning.

• Site and protective barriers: Pool barriers, mapped floodplain development, land disturbance and stream-buffer conditions reviewed through the applicable county permit or site process.

• Road rights: County right-of-way work, notices, safe passage and restoration administered through the responsible road office.

• Sanitary review: Onsite-system construction, modification, malfunction and lagoon protection reviewed by the Health Department.

• Excavation duties: Excavation notice, facility protection and damage-reporting duties under Missouri law.

• Separate private matters: Covenants, easements, ownership and shared-fence disagreements governed by applicable private instruments and legal rights.

USING THIS INFORMATION

This page provides general orientation on how residential fence rules are structured and applied within unincorporated Platte County, Missouri. Updated November 2026.

In addition to local fence rules, certain Missouri laws apply statewide. See Statewide Fence Laws in Missouri.

It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with the identified municipality, including its actual municipal or county class, charter, adopted program or special district, and each function’s verified territory, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Missouri law. Applicable requirements depend on the property’s actual facts and the respective authority of the identified offices. Private agreements and recorded rights remain separate from government approvals. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern.