FENCE RULES – ST. CHARLES (COUNTY), MISSOURI
OVERVIEW
This page covers residential fencing in unincorporated St. Charles County, Missouri. Incorporated cities have their own zoning; a St. Charles mailing address or a county-provided inspection service does not make county zoning apply inside a city.
For residential districts and subdivisions in agricultural districts, St. Charles County generally allows six-foot side and rear fences but prohibits fencing in the required front yard, with specific corner- and through-lot exceptions. The adopted building code exempts fences not over seven feet from a building permit, while zoning and other approvals remain separate. Wood, vinyl/PVC and chain-link are not prohibited ordinary materials; solid metal panels are. Corner visibility, pools, drainage, watercourse buffers and animal enclosures can change the design. On agricultural acreage, the land’s use and sewage system affect which requirements apply. Updated November 2026.
| Quick question | St. Charles County answer |
|---|---|
| Permit or approval | The adopted residential code exempts fences not over 7 feet from a building permit. The county permit page uses an over-6-foot threshold; Building and Code Enforcement resolves that difference for a proposal. Land-use and site approvals are separate. |
| Typical fence height | In residential districts and agricultural subdivisions: 6 feet along sides/rear; no fence in the required front yard except the stated corner/through-lot branches. |
| Placement & property lines | Side/rear lot-line placement is allowed without protruding onto adjacent land or right-of-way. Front yards, corner sight areas and special site restrictions still control. |
| Common fence materials | Wood: not prohibited as an ordinary material. Vinyl/PVC: not prohibited. Chain-link: not prohibited; pool opening rules are additional. Solid metal panels are prohibited in the stated residential/subdivision scope. |
| Important local conditions | Fence rules may be further affected by corner and through lots, pools, public rights-of-way, drainage, watercourse buffers, floodplains, agricultural use, animal enclosures and existing onsite systems. |
| Official local resource | St. Charles County residential permits and Building and Code Enforcement |
The table summarizes the ordinary framework. The sections below explain its applicability, exceptions and site-specific requirements.
GOVERNANCE
St. Charles County operates under its charter as a first-class charter county. Its Unified Development Ordinance governs unincorporated territory. Planning and Zoning administers land-use and floodplain approvals; Building and Code Enforcement, within Community Development, administers the adopted residential, pool, property-maintenance and onsite-sewage codes. The county uses locally amended 2021 construction codes, including direct adoption of the 2021 International Swimming Pool and Spa Code.
The county provides some building or onsite-sewage services to contracting cities. The county’s Parcel Permit Lookup Tool identifies delegated service for a parcel; that arrangement does not transfer county zoning into a city. Weldon Spring land-use approval, for example, is separate from county building review. The County Engineer and Director of Development Review have the stated sight-distance approval roles, and road/right-of-way work follows the responsible road authority.
PERMIT AND APPROVAL REQUIREMENTS
• Fence building permits and replacement: The adopted residential code covers construction, alteration, replacement and repair. Its amended R105.2 expressly exempts fences not over 7 feet from a building permit. The county’s residential-permit webpage instead lists fences over 6 feet and pool barriers as permit work. For a fence between those thresholds, Building and Code Enforcement is the office to resolve the published difference before work. The zoning maximum remains six feet in the residential/subdivision settings below; the building exemption does not authorize a taller fence.
• Separate land-use approval: The county land-use process requires approval for construction, alteration or repair of buildings and structures and nonagricultural regrading below 5,000 square feet. Nonfloodplain electrical and septic repairs are exceptions. Applications include a plot plan and work description. A building-permit application also serves as the land-use application; where no building permit is needed, a separate land-use application is used when land-use approval is required. Planning and Zoning determines its application to the proposed fence and site.
• Plans, installers and fees: Where a fence permit is required, the county calls for contractor names, plans, estimated cost and a plot plan showing property lines, easements and relevant septic-system details, followed by applicable inspections. Fence installers need the county license before permit-required work. The fee provision sets $60 or estimated construction cost multiplied by the current fee multiplier, whichever is greater. Estimated cost is the higher of the applicant’s estimate or the division’s estimate under the specified valuation method. Fees may be adjusted annually.
• Floodplain development: In a designated flood-hazard area, §405.325 requires a separate permit for each improvement before covered development, substantial improvement or nonagricultural regrading. The cited agricultural-levee repair exception is not a general fence exception. Planning and Zoning administers the application. The floodplain permit follows the building-permit term, or lasts 2 years when there is no building permit. Floodway encroachments require an engineer’s certification that flood levels will not increase.
• Land disturbance: A land-disturbance permit is required for disturbance of 5,000 square feet or more. Listed exceptions require no change in drainage patterns or sedimentation onto neighboring property. They include qualifying agricultural/horticultural work following soil-conservation recommendations, gardening at one- or two-family dwellings, specified vegetation replacement of no more than 10,000 square feet with erosion controls, utilities, and work covered by a road-right-of-way special permit. For disturbance of 5,000 square feet or more, fence work must meet an applicable exception to avoid this permit. Smaller projects may still fall under the separate land-use process.
• Work in a public right-of-way: A special-use permit is required before any work in a public right-of-way, including work by an individual property owner. A road permit does not establish a right to place a fence where zoning prohibits encroachment.
FENCE PLACEMENT RULES
• Residential districts and agricultural subdivisions: The fence geometry and ordinary-material rules in §405.415 apply in residential districts and subdivisions in agricultural districts. Unsubdivided agricultural acreage has a different scope. In the covered areas, a fence may follow a side or rear lot line, but no part may protrude onto neighboring property or a right-of-way.
• Required front yards: Fencing is prohibited in the required front yard, the space between the front lot line and the minimum setback line. A recorded plat’s setback controls; otherwise district standards apply. Required front-yard depths are 50 feet in RR, 35 feet in R1A, 25 feet in R1B/R1C, 20 feet in R1D/R1E, and 25 feet in R2. The A district uses 50 feet, reduced to 25 feet for lots of record smaller than 1 acre; AT uses 50 feet. R3A/R3B use 20 feet from the external development-site limits. Planned districts and manufactured-home parks have their own development/buffer provisions. These lines identify the required yard; the following fence-specific exceptions still apply.
• Corner-lot fence exceptions: A fence beside the principal structure on a corner lot may be up to 6 feet high and at least 1 foot from the street right-of-way if erected before January 1, 2010. A separate exception allows the same one-foot setback and six-foot height where no principal structures in the same block face that street. Sight-clearance requirements remain applicable.
• Through lots: A lot extending between two streets generally follows the preceding restrictions. A fence may be 1 foot from the right-of-way on the other street frontage if all principal structures in the same block face the same street and direction and no vehicular access to the other street exists in that block. Both conditions are required.
• Pool and deck location: Pools, hot tubs, spas and incidental pumps/filters cannot occupy the required front yard. A pool and deck must be at least 5 feet from side lines and 10 feet from the rear line; on A/RR lots of at least 3 acres, both side and rear distances are 10 feet. On a lot with two or more frontages, the nonfacing front may contain the pool/deck and required barrier if no principal structure in the same block faces that street/direction. The pool/deck must then be 10 feet from that right-of-way. These pool/deck distances are separate from fence placement.
• Drainage and pipeline easements: A proposed structure cannot redirect stormwater onto previously unburdened neighboring property or leave inadequate stormwater conveyance. Pipeline easements must remain clear of trees, bushes and structures; buildings and accessory structures are prohibited there except consented street/utility crossings. The separate 25-foot building setback is not a general fence setback. Recorded easements and plat restrictions may control additional parts of the lot.
• Natural-watercourse buffers: Mapped natural watercourses generally have buffers where clearing, grading, construction and vegetation disturbance are prohibited without the specified approval. Measure from the bank edge: 50 feet along the main branches of Dardenne, Peruque, Femme Osage, Big and McCoy creeks, and 25 feet along other watercourses left natural. Primarily agricultural/farming land is excluded except for the stated berm and dam controls. Listed alterations need express written approval. The narrow accessory-structure adjustment requires a lot smaller than 3 acres existing on January 30, 2002, all its structures already existing on that date, no other variance, the minimum necessary encroachment and no substantial impairment of the stated buffer policy and standards.
• Boundaries and survey markers: A survey establishes the boundary; an old fence, hedge or mowing line does not establish it by itself. A surveyor’s real-property report is not a boundary survey for locating a new fence. Missouri §60.355 protects public-land corners, property markers, benchmarks and survey-control monuments from knowing movement, removal, defacement or destruction, except by a registered land surveyor. Violation is a class B misdemeanor. The statute provides restoration-survey costs and the affected owner’s stated attorney-fee remedy.
• Before digging fence-post holes: Missouri’s underground-facility law covers digging, augering and driving on private land as well as public property. Under §319.026, notice to the notification center is required at least 2 working days, but no more than 10 working days, before expected excavation. Missouri 811 is the notice service. The two-working-day period begins at midnight following receipt; Saturdays, Sundays and legal holidays do not count. The notice supplies the excavator and responsible-person contacts, location, expected start, depth, type of work and other required details. Utility marks do not establish a property boundary or permission to use another person’s land.
• Locate responses: Operators ordinarily respond within two working days unless the excavator agrees to extend the scheduled start. Work cannot start before the scheduled date unless all facilities have been confirmed located. If an operator has not responded to a proper original notice, §319.030 requires a second no-response notice before excavation. The operator then has 2 hours to mark or contact the excavator with when marking will occur. A notice received by 2 p.m. requires marking that working day; a later notice requires completion by 10 a.m. the next working day. Only failure of the statutory mark-or-contact requirement permits starting under that exception. Careful and prudent excavation remains required.
• Ticket life and usable markings: Under §319.025, the notice remains operational through 11:59 p.m., 21 consecutive calendar days from the work start date. If work does not begin within ten working days of the request, a relocation request is required before starting. Preserve visible marks; unusable marks require a remark request using the original notice period. The ordinary approximate-location strip is the facility width plus 2 feet on each side, with a wider designation for the specified unusual locating conditions. Determine appropriate practices for confirming horizontal and vertical location and use hand or soft digging where possible. An unmarked or incorrectly located facility must be reported through the notification center; the operator has two hours to contact the excavator or locate it correctly.
• Damage during excavation: Report facility damage, dislocation or disturbance, including damage to trace wires, protective encasements or stakes, to the notification center. Contact or damage causing a hazardous-liquid or gas release requires an immediate 911 call. Do not conceal damage or attempt repairs without the facility owner’s authorization. The narrow allowance for emergency temporary sewer repairs after reporting is to prevent further damage and does not cancel notification. For an excavation necessary because of a statutory emergency, all reasonable precautions to protect facilities remain required, and notice must be given as soon as practical. Within two hours, the operator must mark or contact the excavator with immediately available information and, if unable to mark within that period, state when it will mark. Excavation in a state highway or its right-of-way also requires the Missouri Highways and Transportation Commission permit under §319.025, subject to its railroad-right-of-way exception.
• Removing a division fence: Under Missouri’s general partition-fence system, §272.120 requires all owners’ consent before removal of a division fence, except to open a public road or highway. Section 537.350 separately requires six months’ written notice to the adjoining field owner for its partition-fence removal or opening branch where the adjoining fields are cultivated. It also addresses voluntarily opening or throwing down another enclosure’s doors, bars, gates or fences and leaving them open or down. The consent and written-notice duties are separate. Section 537.350 provides $5 plus double actual damages and costs. Section 537.360 limits covered recovery to single damages and costs when there was probable cause to believe the land or thing was the defendant’s own. Specialized watercourse/log-driving exceptions are separate from ordinary yard-fence removal.
FENCE HEIGHT AND VISIBILITY RULES
• Rural fields where livestock are kept: Where Missouri’s general partition-fence system applies, §§272.010–272.020 require a lawful fence for fields and enclosures where animals are kept. A lawful fence consists of posts and wire or boards at least 4 feet high, agreed upon by adjoining owners or determined by the associate circuit court. Posts must be firmly set no more than 12 feet apart, with wire or boards securely fastened and spaced to resist horses, cattle and similar livestock. County local-option rules and private agreements can affect shared-fence duties; these agricultural provisions do not raise a local residential fence-height limit.
• Side and rear fences: In residential districts and agricultural subdivisions, side and rear fences may be at most 6 feet high, with no general openness requirement. Height runs from established grade to the topmost fence section; on a slope, the fence follows the ground contour. Masonry pillars used with ornamental iron may be up to 25 percent higher than the attached fence, including decorations and appurtenances, and no wider than 24 inches.
• Street corners and driveways: In the designated sight areas, objects over 3 feet above street grade that obstruct vision are prohibited unless approved by the County Engineer or Director of Development Review. Vegetation may overhang with at least 7 feet of clearance above ground. A street-corner triangle joins points 30 feet along the intersecting property lines, extended where the corner is rounded. At a street and driveway or alley, the triangle instead joins points 10 feet along the intersecting pavement edges.
MATERIAL AND CONSTRUCTION LIMITS
• Livestock outside the enclosure: Missouri §270.010 prohibits an owner from permitting horses, mules, asses, cattle, swine, sheep or goats to run at large outside the owner’s enclosure. Anyone may restrain them, and law officers must. If the owner is known, written notice must be given within 3 days, stating feeding/keeping compensation and claimed damages. The owner owes reasonable taking-up, keeping and feeding compensation plus actual damage. For a public-road or highway accident, the statute preserves a defense where the owner establishes no fault or negligence. The stray-law route applies when the owner is unknown or a notified owner fails to pay taking-up, feeding and keeping compensation; unpaid damages alone do not trigger that route.
• Wood: Wood is not prohibited as an ordinary fence material in the residential/subdivision provisions. The fence must meet the applicable yard, construction and maintenance rules.
• Vinyl/PVC: Vinyl and PVC are not prohibited ordinary materials under those provisions; height, location and any special barrier requirements still apply.
• Chain-link: Chain-link is not prohibited for an ordinary yard fence. A pool enclosure must also meet its smaller opening and anti-climbing requirements.
• Materials and finished side: Covered residential/subdivision fences must use the same or harmonious materials. Solid metal-panel fences are prohibited. Vertical and horizontal supports and crossmembers must face inside the lot.
• Barbed wire and electrical fences: In R districts, barbed-wire and aboveground electrical fences are prohibited in yards. This restriction is tied to the residential zoning classification; it does not prohibit all agricultural fencing or define the rules for belowground pet-containment systems.
• Fence and wall maintenance: Fences and walls must remain structurally sound and in good repair. Exterior surfaces must be in good condition and free of organic growth. Wood other than decay-resistant wood needs protection; peeling, flaking, fading or chipped paint must be corrected. Rust-prone metal needs treatment except surfaces designed to stabilize by oxidation. The local scope exception requires assessor-classified agricultural land used exclusively for agricultural production, or such agricultural land used for conservation/hunting at least 500 feet from assessor-classified residential land. A county finding of danger overrides that exception.
• Pool covers and construction fencing: Outdoor pools and spas and indoor swimming pools need compliant barriers under the adopted 2021 International Swimming Pool and Spa Code. A spa or hot tub with a qualifying lockable ASTM F1346 safety cover, or a pool with a qualifying powered ASTM F1346 safety cover, is exempt from §§305.2–305.7. In-ground pool and spa sites still require construction fencing at least 4 feet high, from excavation until the permanent barrier is complete.
• Pool barrier height and openings: A barrier under §305.2 must be at least 48 inches high, measured above grade on the side away from the pool around the entire perimeter and for 3 feet horizontally outside. The bottom gap is at most 2 inches over grass or gravel or 4 inches over a solid surface, measured on the side away from the pool or spa. If mounted on a pool wall, the gap between the wall top and barrier bottom is at most 4 inches. Openings cannot pass a 4-inch sphere. Solid barriers cannot provide handholds or footholds beyond normal construction tolerances and tooled masonry joints.
• Pool fence members and chain-link: When horizontal-member tops are less than 45 inches apart, horizontal members must face the pool, and vertical-member gaps and decorative cutouts are limited to 1¾ inches. When horizontal-member tops are at least 45 inches apart, vertical gaps may be 4 inches, but decorative cutouts remain limited to 1¾ inches. Chain-link openings cannot exceed 1¾ inches. Slats used to reduce chain-link openings must be fastened at the top and bottom. Diagonal-member openings are limited to 1¾ inches, and diagonal members cannot exceed 45 degrees from vertical.
• Removable mesh pool fencing: Mesh other than chain-link must follow manufacturer installation instructions. Its bottom must be no more than 1 inch above the deck, installed surface or grade. Clearance between the mesh bottom and solid surface must not allow the fence to lift more than 4 inches from grade or decking. No 4-inch sphere may pass beneath any panel, and the maximum bottom-to-solid-surface clearance is 4 inches from grade or decking. Each section’s attachment device must be at least 45 inches above grade; the code gives a hook-and-eye latch with a spring-actuated retaining lever as an example of attachment security. Hinged gates follow §305.3. Patio-deck post sleeves must be nonconductive. Mesh fencing cannot be mounted atop an onground residential pool, and its inside face must be at least 20 inches from the nearest pool or spa water edge.
• Pool gates and doors: Access gates and doors must accommodate a lock. Pedestrian gates and doors open outward, away from the pool or spa, and self-close and self-latch. Nonpedestrian utility or service gates and doors remain locked when not in use. Double or multiple doors and gates need at least one secured leaf and a self-latching adjacent leaf.
• Residential pool latch heights: An outside-accessed latch release that is not self-locking must be at least 54 inches above the finished floor or ground surface. For a self-locking key, electronic or combination mechanism, both the lock control and latch release must be no higher than 54 inches above the finished floor or ground surface. At private pools, a self-latching gate with its sole release on the pool or spa side must place that release at least 3 inches below the gate top. Openings in the door, gate and barrier within 18 inches of an inside latch release cannot exceed ½ inch in any dimension.
• Equipment outside a pool barrier: Equipment on the same lot, including pumps, filters and heaters, must be at least 36 inches from the outside of the barrier when located outside that barrier.
• A building wall used as the pool barrier: Where a dwelling or structure wall provides direct access to the pool, §305.4 allows specified protective alternatives. The alarm option covers doors, gates and the specified windows with sills below 48 inches above the indoor finished floor, using a UL2017 audible water-hazard entrance alarm. The window provision covers operable windows. Alarm-deactivation controls must be at least 54 inches above the finished floor in dwellings not required to be Accessible, Type A or Type B units; in those accessible categories they must be 48–54 inches above the finished floor. Alternatives include a listed and labeled ASTM F1346 safety cover or approved equivalent protection, such as self-closing, self-latching doors.
• An onground pool wall used as the barrier: A pool wall used alone must have its bottom on grade and its top at least 48 inches above grade around the entire pool perimeter, meet §305.2 and be approved by the manufacturer for barrier use. A wall with a top-mounted barrier must place the top of the barrier at least 48 inches above grade around the entire pool perimeter, with both wall and barrier complying with §305.2. Access ladders or steps must be capable of being secured, locked or removed to prevent access, unless enclosed by a separate complying barrier. Openings created by securing, locking or removing them cannot pass a 4-inch sphere. Top-mounted barriers must follow manufacturer instructions.
• Natural pool-barrier alternatives: The natural-water-edge exception applies only where public access to the shoreline is not permitted and the required barrier extends at least 18 inches beyond the water edge. A natural-topography barrier needs governing-body approval and protection equivalent to §§305.2–305.5.
• Existing pools, spas and hot tubs: The county’s property-maintenance code separately covers private pools, spas and hot tubs containing water more than 24 inches deep. It requires a 48-inch fence or barrier above finished ground level, measured on the side away from the pool and self-closing, self-latching gates. A release below 54 inches above the gate bottom must be on the pool side. A gate must positively close and latch when released 6 inches from the gatepost. An existing enclosure cannot be altered, removed or replaced to reduce its effectiveness. Exceptions cover qualifying ASTM F1346 spa/hot-tub covers and private-pool power covers working with the control switch. Pools and covers must remain clean, sanitary and in good repair without stagnant water.
• Hen enclosures: Residential lots of at least 10,000 square feet may keep up to 8 hens; a rooster requires a residential parcel of at least 5 acres. The secure enclosure must be in the rear yard, use wire mesh, wire grid or chicken wire no higher than 6 feet, and provide at least 10 square feet per hen. Keep the enclosure and coop at least 10 feet from property lines and 25 feet from another residence. The enclosure must be in good repair and prevent passage over, under or through, including head or mouth passage. No runoff or nuisance is allowed. The coop’s separate minimum is 4 square feet per animal, with a 100-square-foot maximum; those are not the fenced-yard area requirements.
• A dog subject to dangerous-dog confinement: The applicable order or agreement requires the dog indoors, behind a secure fence, or in a secure locked pen or structure. A pen or structure must be at least 5 by 10 feet, with strong sides and a secure top. If no bottom is secured to its sides, the sides must extend at least 12 inches into the ground. Provide adequate shelter, prevent easy exit and exclude other animals except a mother with her young under three months. Warning notices are required at each entrance and each enclosure side. The pen specifications apply to that confinement option, not to indoor confinement.
• Local onsite sewage and new lagoons: The county onsite-wastewater program covers unincorporated and contracting areas. It permits installation, alteration, expansion and repair. Changing/cleaning filters, adjusting head pressures and like-for-like replacement of pumps, aerators or blowers are excepted. New systems normally need 3 acres, subject to specific local approval exceptions; public sewer is considered available when within 200 feet of the property line. The county prohibits new lagoons and excludes lagoons and wetlands from new alternative systems. Any lagoon-fence discussion below concerns an applicable existing lawful lagoon.
• State onsite-system acreage conditions: Missouri §701.031 excludes the owner of a single-family-residence lot of at least 3 acres, or the owner of a residential lot of at least 10 acres with no single-family-residence onsite sewage system within 360 feet of any other onsite sewage system and no more than one single-family residence per ten acres in the aggregate, from the stated state onsite provisions only when the remaining conditions are met. The exclusion does not cover lots adjacent to lakes operated by the Corps of Engineers or a public utility. Every point of the system must be more than 10 feet from any adjoining property line. No effluent may enter adjoining property, contaminate surface water or groundwater, or create a nuisance as determined by a readily available scientific method. Section 701.047 permits more restrictive local standards. These state conditions do not waive the separate local sewage program. The state’s $90 onsite application fee is suspended from August 28, 2026; local fees are not suspended by that state action.
• An existing lawful lagoon: Where the state lagoon rule applies, the pond area needs a fence at least 4 feet high, made of welded, woven or chain-link wire no smaller than 14 gauge. Cattle or hog panels may be substituted with tee line posts. Posts must be pressure-treated wood, galvanized and/or painted steel, and driven, tamped or set in concrete. Line posts must be no more than 10 feet apart; corner posts must be properly braced. The suggested depths are 18 inches for line posts and 24 inches for corner posts. Construction must be sound with no bottom gaps or openings.
• Lagoon fence location and gate: The fence cannot be closer to the water’s edge at the 3-foot operating depth than the center of the berm. Placement exactly on the berm center is not required. The rule recommends that setbacks not exceed 30 feet from the water’s edge. A properly hinged 4-foot-high gate of comparable material needs an effective latch. A 36–48-inch gate width is recommended for mowing and maintenance access. The fence must be complete before dwelling occupancy. Post depths, maximum water-edge setback and gate width are recommendations; fence height, bracing, maximum line-post spacing and effective enclosure are requirements. These provisions do not authorize a new lagoon where local law prohibits one.
• Licensed family child-care outdoor areas: For licensed family child-care homes, an outdoor play area must be available on or adjoining the property, convenient and accessible without hazard. Fencing is required where needed to protect children from traffic, water or other hazards. Homes initially licensed after the rule’s effective date, and new fences installed at existing facilities, need a fence at least 42 inches high. Independently, all fences must prevent children from crawling or falling through, or becoming entrapped.
• Licensed family child-care pools: Swimming and wading pools must be fenced to prevent children’s access. For family homes initially licensed after the rule’s effective date, the pool fence must be at least 42 inches high with a locked gate. The state rule allows an above-ground-pool option of a 42-inch fence around the pool top with barricades at the steps to the pool deck. Applicable local pool rules can be stricter; the licensing provision does not reduce their requirements.
PRIVATE RESTRICTIONS
Recorded easements, covenants, subdivision restrictions, homeowners-association rules and private boundary or maintenance agreements can add obligations. County §405.040 preserves private easements and covenants while allowing stricter public development requirements. A county permit does not decide ownership, establish a boundary, authorize interference with an easement, or settle a neighbor’s share of fence costs. A gate does not by itself make a fence across an access easement lawful.
Agricultural partition-fence cost allocation depends on the applicable Missouri system, property use and agreements. It is not a general rule that neighbors must split the cost of every residential privacy fence. Parcel-specific planned-development and recorded design conditions can apply even where no general private-home historic-fence certificate process is provided.
REVIEW AND ENFORCEMENT CONTEXT
Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:
• Permits and site work: Building and land-use review, pool barriers, floodplain development, land disturbance and work in public rights-of-way.
• Placement and visibility: Required front yards, corner and through-lot exceptions, sight triangles, easements, watercourse buffers and drainage.
• Safety and maintenance: Damaged fences, dangerous features, pool gates, animal enclosures and applicable existing lagoon fences.
• Private rights: Boundary, ownership, covenant, access and contribution disputes remain separate from county code administration.
USING THIS INFORMATION
This page provides general orientation on how residential fence rules are structured and applied within unincorporated St. Charles County, Missouri. Updated November 2026.
In addition to local fence rules, certain Missouri laws apply statewide. See Statewide Fence Laws in Missouri.
It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with the identified municipality, including its actual municipal or county class, charter, adopted program or special district, and each function’s verified territory, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Missouri law. Applicable requirements depend on the property’s actual facts and the respective authority of the identified offices. Private agreements and recorded rights remain separate from government approvals. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern.