FENCE RULES – MIDWEST CITY (CITY), OKLAHOMA
OVERVIEW
This page applies to residential fence work within the City of Midwest City, Oklahoma. A Midwest City mailing address does not establish that a property lies within the incorporated city limits. Updated November 2026.
Midwest City requires a permit before residential fence construction. For single-family and two-family properties, ornamental fencing past front or side building lines may reach four feet only with at least half its area open; taller fencing there needs Board of Adjustment approval. Rear-yard fences may reach eight feet. The City expressly allows wood, vinyl, chain-link and several other materials, but imposes detailed slat, steel-panel, coating and post restrictions. Sight triangles must remain free of fences, and normal surface drainage cannot be blocked. Conditional animal-enclosure distances matter on acreage. Private pools have overlapping local enclosure and maintenance provisions, with different cover exceptions that should not be treated as one universal waiver.
| Quick question | Midwest City answer |
|---|---|
| Permit or approval | A City permit is required before any residential fence is constructed. Include material and dimension information. Ordinary repair and separate Board of Adjustment approval have their own conditions. |
| Typical fence height | Past front/side building lines: ornamental fencing up to four feet with at least fifty percent open area; taller needs Board approval. Rear yards: eight feet. No separate universal interior-side-yard maximum is stated in this fence subsection. |
| Placement & property lines | The front/side ornamental allowance can extend to property lines, subject to visibility and other restrictions. Keep fences out of rights-of-way and sight triangles, preserve easements and do not obstruct drainage. |
| Common fence materials | Wood: expressly approved with applicable slat and post limits. Vinyl/PVC: vinyl expressly approved, subject to applicable construction limits. Chain-link: expressly approved. Material approval does not waive openness or placement rules. |
| Important local conditions | Fence rules may be further affected by building-line frontage, Board-approved exceptions, corner visibility, drainage channels, floodplain development approval, floodplain-adjacent subdivision conditions, retaining-wall easements, patio-home access easements, pools, animal enclosures, lot size and private restrictions. |
| Official local resource | Midwest City Permits and Inspections |
The table is for quick reference; the corresponding sections below contain the conditions and exceptions. Before purchasing materials or beginning construction, read the applicable sections and official links and confirm site-specific requirements with Engineering and Construction Services, Community Development and the responsible office for each separate issue.
GOVERNANCE
The City administers municipal construction, zoning and property-maintenance requirements within its incorporated limits. Engineering and Construction Services handles permit and inspection administration, while Community Development administers the applicable zoning and subdivision provisions. The Board of Adjustment decides the specified fence exceptions; the City Engineer has the right-of-way and sight-triangle roles assigned in those exceptions and serves as the floodplain administrator for separate floodplain development approval. Animal-enclosure rules and private-pool rules remain separate from ordinary fence zoning.
Local sections 9-5 and 9-66 retain 2018 construction-code adoption language. Oklahoma’s 2024 International Residential Code with Oklahoma amendments became effective September 14, 2026 as the state technical baseline. An older local adoption does not lower the statewide minimum or replace the City’s express residential fence-permit requirement.
Property maintenance has parallel adoption provisions: Section 9-5(i), amended in August 2025, expressly adopts the 2018 International Property Maintenance Code with section 9-16 amendments. Housing section 20-1 separately adopts the latest edition upon publication of its Code and Commentary, with section 20-2 amendments; the 2024 Code and Commentary has been published. Both provisions remain in the municipal code. Their common fence-upkeep requirements and differing pool-cover exceptions are explained below, together with the separate section 39-20 pool enclosure rule. A later edition’s exception does not by itself cancel that standalone local rule.
The official municipal code contains the zoning, building, animal and pool provisions. Approval under one system does not decide private ownership, release an easement or excuse a separate applicable requirement.
PERMIT AND APPROVAL REQUIREMENTS
• Residential fence construction: Appendix A section 5.2.3 requires a City permit before any residential fence is constructed. The owner must provide material and dimension information with the application. A generic model-code height exemption does not replace this express local requirement.
• Permit administration: The City’s permit process reviews plans against construction codes, zoning and ordinances; required fees are paid and the permit issued before work. Keep the approved plans and permit at the site and submit changes for review rather than departing from the approved work. Use the City’s Permits and Inspections resource for current application and inspection instructions.
• Fence fee: Section 9-47 lists a fifty-dollar flat fence fee. Its separate state-fee provision remits four dollars and fifty cents for permits associated with the adopted codes in section 9-5. Confirm the actual invoice and any applicable charges rather than treating the listed fence line as every possible total. The subdivision provision’s ten-dollar screening-fence or wall permit and its approved-plan or minor-subdivision waiver concern that separate screening context, not the ordinary residential fence fee.
• Repair and replacement: Section 9-7’s residential permit provision preserves an exception for ordinary repairs that violate no code and refers to section 9-2. Section 9-2 addresses homeowner work; the definition in section 9-1 describes same-or-equivalent replacements or renewals of systems or structures within a building and its service equipment, without the stated health or safety effects. That language does not promise an exemption for replacing an outdoor fence. The detailed structural, equipment and egress exclusions in section 9-6 belong to the separately amended International Building Code. Appendix A section 5.2.3 still expressly requires a permit before residential fence construction and supplies no numeric same-location or percentage-replacement exemption. Confirm the treatment of proposed fence repair with the City before work.
• Fence beyond front or side building lines over four feet: Obtain Board of Adjustment approval before installation under section 7.8.2(G), in addition to the fence permit. The request is an exception processed through the appeals procedure. If at least fifty percent of property owners within three hundred feet object, approval requires a three-quarters vote of the Board’s total membership. Approval carries the access, visibility, gate and placement conditions below.
• Board-approved frontage fence conditions: Maintain public-safety access; the owner assumes losses when responding safety services remove impediments such as locks, chains or animals. Keep the fence structurally sound, attractive and in good repair. Front-yard fencing cannot be sight-proof through construction or ornamentation and must preserve clear vision when backing onto a street. Provide at least one gate with an unobstructed three-foot clear width; an arch over it must keep at least seventy-eight inches of clearance. Dedicate any additional right-of-way or sight triangles required by the City Engineer before permit issuance. The further gate, hydrant and paving-clearance conditions are stated in the placement section.
• Retaining walls: Under zoning sections 5.10.1–5, apply for and obtain permit approval before beginning any retaining wall; a separate permit is unnecessary if the wall is shown and approved on a site plan. A wall higher than two feet must comply with Midwest City standards or be designed and sealed by a professional engineer. Measure from the top of the footing to the top of the wall. All retaining walls must satisfy standard engineering practices and the applicable subdivision ordinance. A fence project incorporating a wall must address the wall rules separately.
• Floodplain development permit: Chapter 13 applies to areas of special flood hazard within the City. Its definition of development includes man-made changes to improved or unimproved land, including structures, filling, grading and excavation. A fence or wall project there must address the separate floodplain development permit with the City Engineer as floodplain administrator. Section 13-37 calls for the administrator’s application and scaled plans showing the project’s location, dimensions and elevations relative to the hazard area, together with the extent of proposed watercourse or natural-drainage changes. If a watercourse is altered or relocated, maintain its flood-carrying capacity within the altered or relocated portion under section 13-36(b)(7). Provide the submissions applicable to the project; the occupied-building floor and floodproofing certifications are not universal fence paperwork. The section lists a twenty-five-dollar nonrefundable application fee. This approval is separate from the ordinary fence permit and the special subdivision fence design below.
FENCE PLACEMENT RULES
• Property lines and street rights-of-way: The ornamental front/side allowance can extend to the residence’s front and side property lines only within the applicable conditions. Fences and screening, including hedges, cannot extend into the street right-of-way. Locate the legal boundary independently of an old fence, hedge, tax map or pavement edge; the pavement edge does not define the right-of-way. Recorded utility and access rights remain relevant even where zoning permits a property-line fence.
• Board-approved frontage fences: Gates must avoid leaving vehicles in the paved right-of-way while opening or closing. Fencing cannot obscure or restrict a fire hydrant or fire connection. The applicant must determine the property boundaries; a fence built in the street right-of-way must be moved at the owner’s responsibility. If the right-of-way line is less than twelve feet from the paving edge, the approved fence must be set back at least twelve feet from that paving edge. These are the section 7.8.2(G) exception conditions, not a universal twelve-foot ordinary-yard setback.
• Sight triangles: No fence, wall, hedge or any portion of one may be located in the sight triangle. The geometries are given in the height and visibility section; a short or open fence is not automatically permitted inside the protected area.
• Surface drainage and open paved channels: No fence or wall may impede normal surface drainage. Section 13-71(c) permits fences immediately adjacent to an open paved storm-drainage channel or farther away in its channel-improvement context. It also requires City-specification channels and side slopes above the paved section shaped and sodded at four horizontal to one vertical or flatter. That channel provision does not release a recorded easement or waive right-of-way, sight-triangle or drainage-flow restrictions.
• Subdivision retaining walls near property lines: Section 38-54 applies to retaining walls built within five feet of a property or proposed property line in a subdivision; it is not a five-foot ordinary-fence setback. The wall must be on private property, outside existing or planned rights-of-way, and entirely on one lot rather than straddling the boundary. A wall may cross several properties only with each portion clearly associated with its own property. The section requires masonry or concrete, City design standards and City Engineer approval before an alternative design is constructed. An approved alternative to a required wall must also satisfy the preliminary-plat drainage requirements.
• Retaining-wall grading, access and maintenance: Follow the approved grading plan. Changing a subdivision wall’s grading or design requires plans showing the proposed changes for the entire subdivision and City Engineer approval. Prevent runoff from spilling over the wall onto neighboring property. Section 38-54.3(e) requires side-yard walls designed and built to two inches below the finished-floor elevation shown on the plat; Figure 49 shows a two-inch minimum below the upper finished floor, swales and at least two-percent positive drainage away from foundations. Its five-foot minimum private retaining-wall easement lies on the lower neighboring property, measured from the wall’s bottom where it meets the lowest ground, so the wall owner can access, maintain and repair it. Preserve that recorded access. Where required or requested by the City Engineer, the wall property also has a no-build zone: no structures or swimming pools there, with width set by the applicant’s structural professional engineer and approved by the City Engineer. The owner or applicable homeowners’ association remains responsible for wall maintenance. Check the approved plat and wall plan rather than treating either the easement or no-build zone as a universal yard-fence setback.
• Development in flood hazards and floodways: In an AE area without a designated regulatory floodway, proposed development combined with existing and anticipated development must demonstrate no more than a one-foot increase in base-flood water elevation at any point in the City. Section 13-36(b)(10) provides the stated FEMA conditional map-revision route for development increasing elevation beyond that limit. In an adopted regulatory floodway, section 13-55 prohibits encroachments, including other development, unless hydrologic and hydraulic analysis under standard engineering practice demonstrates no increase in flood levels during the base-flood discharge. Its separate exception requires the City first to apply for conditional FIRM and floodway revisions through FEMA. A fence permit alone does not authorize obstructing flood flow or using one of those revision paths.
• Existing patio homes with a zero side setback: Section 5.5 requires the opposite side setback to be at least ten feet and perpetually free of obstructions except the stated two-foot eave encroachment and normal landscaping. The configuration also requires a recorded five-foot maintenance/access easement on the property adjoining the zero lot line. Preserve that access and the actual approved layout when placing a fence; these dimensions are not setbacks for every Midwest City yard.
• Large-animal enclosures: Article III’s domestic-animal and fowl rules operate subject to zoning; dogs have their separate article. Horses, mules, donkeys, goats, sheep, cattle and similar large animals other than swine require at least one properly fenced acre. For one, two or three whole net enclosed acres, no more than two large animals per whole net acre may be kept. Above three acres, each additional one-fifth acre permits one additional large animal. The enclosure boundary must be at least seventy-five feet from the exterior of a church, business, school or residence other than the owner’s.
• Small-animal and fowl enclosures: Section 8-43 names small animals and fowl except dogs and cats and uses the threshold “any combination of twelve or more.” That branch requires at least two thousand square feet, with twelve or fewer additional animals or fowl for each additional one thousand square feet. Its enclosure must prevent quartering within forty feet of the exterior limits of a church, school, business or residence other than the owner’s. The provision is not a universal twelve-animal cap for every lot.
• Animal enclosures and private wells: The enclosure’s exterior limits must be at least fifty feet from any private water well. Animal-enclosure separation distances are conditional rural-home siting requirements, not ordinary yard-fence setbacks.
• Swine enclosures: Swine are prohibited on parcels of less than forty acres, excluding roadway easements. A qualifying tract may keep no more than twenty grain-fed or three garbage-fed swine, confined at least two hundred feet from a church, school, business or residence not occupied by the owner or keeper. The shipment, sale, transit or other-purpose exception applies only when the swine remain in the City no longer than twelve hours. The tract, numbers and distance requirements remain subject to applicable zoning.
• A survey crossing an existing division fence: Under 4 O.S. section 150.1, when an owner’s survey reflects a property line across an existing boundary or division-line fence, the owner must notify the adjacent owner before damaging or removing the fence or authorizing establishment, location or relocation of improvements, including utilities, on the disputed property. The notice must include the survey, requested relief and notice of possible attorney fees and costs, and must be served as provided for service of process in 12 O.S. section 2004. If no agreement is reached within thirty days after receipt, the owner may bring an action in the district court where the property lies to establish title. The district court must enter temporary relief as necessary to maintain the status quo while the action is pending. Thirty days does not authorize self-help removal or impose a thirty-day deadline to sue; the prevailing party is entitled to attorney fees and costs.
• Improvements found on another owner’s land: Title 4 section 149 provides that a person who built a fence later found by division lines to be on another person’s land may not remove it until paying that landowner the damages caused by its location. If the builder fails to pay and remove the improvement within six months after establishment of the division line and after thirty days’ removal notice from the landowner, the provision makes it part of the real estate belonging to the landowner. Fence viewers may determine disputed damages. Except for substantial buildings, a fence or other improvement made from timber or other material taken from that land cannot be removed until the landowner is paid the material’s value, as determined by fence viewers, and a fence cannot be removed while removal would expose the other party’s crop; removal must await a reasonable time after the crop is secured. Section 152 permits a fence on the line partly on each side and states that its owner has the same removal right as if it were wholly on that owner’s land, provided the fence is no more than five feet from the line. That provision must be read with the other removal and disputed-title protections; section 153 preserves other title proceedings and agreements. Obtain legal advice before relying on these provisions to remove a disputed fence.
Before digging — covered work and exclusions: Under 63 O.S. §142.2, excavation means digging, compressing or removing earth, rock or other material in or on the ground using mechanized equipment or blasting, including such work as augering, boring, drilling, grading and trenching. Moving earth with tools powered only by people or animals is excluded, except in a private or public easement or right-of-way. A separate exclusion covers human-powered burial of a communications provider’s communication lines in such an easement or right-of-way only when the depth is no greater than 12 inches and the work is within 12 inches of that provider’s terminal. The agricultural exclusion covers cultivation for agricultural purposes and augering, dozing by noncommercial dozer operators or digging for postholes, farm ponds, land clearing or other normal agricultural purposes; it is not a blanket exception for any residential posthole. The Act also excludes an individual excavating on that individual’s own property who is not in the excavating business for hire, except in a private or public easement or right-of-way. Do not extend that owner exception to a hired contractor or easement/right-of-way work.
Covered excavation notice and responses: Section 142.6 requires notice before covered demolition, explosives or excavation in a highway, street, alley or other public ground or way, on or near an operator’s underground facilities, or in a private easement. Notify the area’s operators identified through the notification center; an operator known to have no facilities in the area need not be notified, but the excavator remains responsible for facility damage if the notification center was not notified. Give notice at least 48 hours before work, excluding the notification date, Saturdays, Sundays and legal holidays. Check positive responses at the notification center before excavation or demolition to ensure all operators have responded and all potentially affected facilities have been marked. A watch-and-protect response prohibits excavation within 10 feet of the operator’s facility markings without the operator or designated representative present to observe. The notice expires 14 calendar days from the excavation start date; work cannot continue afterward unless a subsequent notice has been submitted under the notice requirements.
Hydrocarbon markings and emergency work: An excavator with actual knowledge of unmarked hydrocarbon and hazardous-liquid underground facilities in the proposed work area must not begin excavation or demolition until notice is given and those facilities are marked. Preserve all hydrocarbon and hazardous-liquid markings throughout the work; notify the notification center if they are no longer visible or are removed and the facilities have not been exposed. Section 142.6’s emergency exception applies when life, health or property is endangered: immediate excavation requires reasonable facility-protection precautions and prompt notice to all operators in the emergency area.
Practical digging precautions: Contact OKIE811 before excavation as a safety step even when a statutory exclusion may apply, unless the project involves no digging. A locate request is not boundary evidence, easement permission or a substitute for permits; private service lines may need separate locating.
FENCE HEIGHT AND VISIBILITY RULES
• Past front or side building lines in single-family and two-family districts: Ornamental fences may reach the front and side property lines if no more than four feet high measured from ground level and at least fifty percent of the total fence area is open to allow visibility into the yard. Chain-link and picket fencing are examples. A fence there over four feet needs the Board approval and conditions described above.
• Rear yards: The fence subsection sets an eight-foot maximum measured from ground level. It does not state a separate universal maximum for every interior side-yard fence behind the building lines. The four-foot frontage rule and its approval route depend on the fence’s actual relationship to front or side building lines.
• Street corners: Measure twenty-five feet along the front and exterior-side lot lines from their intersection, and extend the connecting hypotenuse to the curb to form the protected sight triangle. The fence rule prohibits a fence, wall, hedge or any portion within it.
• Private driveways serving parking for six or more vehicles: Section 5.6.3(B) uses twenty-five-foot measurements along the front lot line and exterior pavement edges of the driveway approach, extends each hypotenuse to the curb, and includes the driveway between the two triangles. This parking-capacity trigger is not every ordinary home driveway.
• Other sight-area controls: Within the right-of-way part, only grasses may be maintained; parking, walls, fences, signs, structures and other plant growth are prohibited. In the remaining sight area, the listed obstructions are barred from ground level to ten feet, with traffic-directional signs no higher than thirty inches excepted; vegetation cannot exceed thirty inches at maturity. Height is measured from the adjacent public-street or private-drive elevation, whichever is higher. The stated exceptions cover traffic-control signs and lighting standards and one private sign pole no more than one foot in diameter. Parking in single-family and two-family driveways is separately excluded from this ordinance; that is not a fence exception. On one-way streets and streets with divided medians, the sight triangle applies only on the side with oncoming traffic.
• Subdivision lots adjoining the one-hundred-year floodplain: Section 38-44(g) sets a site-specific fence standard of six to eight feet measured at grade, no more than fifty percent opacity, and ornamental metal with masonry columns or a masonry base no higher than three feet. Rear or side placement is subject to Community Development Director review, and the lot owner maintains it. These continuing subdivision conditions are not the ordinary citywide front-yard or rear-yard rule.
MATERIAL AND CONSTRUCTION LIMITS
• Approved single-family and two-family materials: Section 5.2.3(B)(3) recognizes wood, vinyl and metal slats with a depth of at least five-eighths inch; wrought iron or aluminum wrought-iron-like fences; brick or stone; chain-link; and qualifying ribbed steel panels. Material approval does not cancel a frontage openness or other site requirement.
• Ribbed steel dimensions: Ribs must be one to one and one-half inches deep, two and one-half to three and one-half inches wide, with six to twelve inches between rib centers. Panels must be twenty-two- or twenty-four-gauge steel, properly primed and factory coated. Cap the tops and keep them level following the lay of the land. Poles cannot extend above the panels. Submit the specifications with the fence-permit application.
• Metal coatings: All metal fencing must have a factory-applied coating. Recognized finishes are powder coating, polyvinylidene fluoride (PVDF), thermal-set silicone polyester or another factory coating approved by City staff.
• Prohibited materials and projecting posts: The single-family and two-family list prohibits sheet metal, plastic, corrugated metal panels and plywood, and prohibits stockade, described as wood, posts. Only post or pole caps may project above the fence line. The same subsection expressly approves vinyl and qualifying ribbed steel; the generic plastic and corrugated-metal prohibitions should be applied with those specific approved categories, rather than presented as a ban on every vinyl or ribbed-steel fence. Submit the actual product and dimensions for approval.
• Small-lot dangerous fencing: On lots smaller than one acre, electrified fences or walls, barbed wire and other substances reasonably capable of bodily harm are prohibited. A larger lot’s absence from that particular prohibition is not blanket approval of every electric or hazardous fence or relief from zoning and animal rules.
• Animal-confinement construction: The fence must harmonize with the buildings and immediate surroundings in neatness and appearance, prevent escape and animals running at large, and comply with applicable zoning. The animal-enclosure acreage and separation requirements above have their own scope; they do not convert every household boundary fence into an animal enclosure.
• Upkeep and surface condition: Owners must keep fence materials attractive, free of rust, in good repair, safe and sanitary. Both adopted property-maintenance editions require accessory fences and walls structurally sound and in good repair. Local amendments to section 304.2 require fence exteriors in good condition and correction of peeling paint; rusting or corroding metal must be stabilized and coated, except surfaces designed to stabilize by oxidation. The amendment’s separate wood-treatment sentence concerns wood on a dwelling, with its stated cedar or redwood siding exception; it is not a blanket command to paint every wood fence.
• Qualifying annexed agricultural land under state law: 11 O.S. section 21-103(J) exempts qualifying annexed agricultural land from municipal land-use and building-construction restrictions only to the extent the use or construction relates to agricultural purposes. Its alternatives are parcels of five acres or more used for agriculture and annexed on or after July 1, 2003, or parcels of forty acres or more used for agriculture before annexation and remaining in uninterrupted agricultural use. Ordinances under section 43-101.1 are excepted. A separate conduct clause applies where there is no residence within fifty feet of the parcel boundaries: municipal conduct rules that would not address an offense under state law do not apply, subject to the statute’s municipal water, wastewater or sewer environmental-compliance condition. Section 21-103(K) preserves airport, spaceport and military-installation operational protections and section 43-101.1 ordinances. Acreage alone does not exempt an ordinary residential fence project; verify agricultural use, annexation history and the statutory limits.
• Standalone private-pool enclosure rule: Section 39-20 requires a complete enclosure for a private pool, hot tub or spa containing water more than twenty-four inches deep. It must be at least forty-eight inches above finished ground on the side away from the water. Gates and doors must self-close and self-latch; releases below fifty-four inches from the gate bottom must be on the pool side. The gate must successfully close and latch from six inches open. An existing enclosure cannot be altered to reduce its effectiveness. The local hot-tub or spa exception requires a safety cover lockable by key, combination or another safety lock and capable of supporting at least seventy-five pounds at its center.
• Parallel pool-maintenance provisions: Both the 2018 and 2024 property-maintenance section 303.2 have the same more-than-twenty-four-inch, forty-eight-inch barrier, fifty-four-inch latch-release, six-inch closure and no-reduction-in-safety branches. Their cover exceptions differ: the 2018 provision excepts ASTM F1346 safety-covered spas or hot tubs; the 2024 provision specifies lockable ASTM F1346 spa/hot-tub covers and also a working, control-switch-operated ASTM F1346 swimming-pool power cover. Those edition-specific exceptions do not cancel section 39-20 or its separate lockable, seventy-five-pound-supporting spa/hot-tub cover conditions. A pool power cover is therefore not a published universal waiver of all City enclosure requirements.
• State residential pool enclosure: Oklahoma IRC section R328 applies to residential pools, spas and hot tubs requiring a permit. R328.2 requires swimming pools to be completely enclosed by a fence or barrier at least four feet high, or a screen enclosure; openings must not pass a four-inch-diameter sphere. Its exceptions concern pools, spas and hot tubs on lots in excess of two acres, and a swimming pool with a power safety cover or a spa with a safety cover complying with ASTM F1346. Exactly two acres does not satisfy the acreage exception, and the spa-cover wording is not an automatic exception for every hot tub or ordinary pool cover. These exceptions are stated in R328.2 and do not cancel the separate Midwest City enclosure provisions.
• State residential pool gates: R328.3 separately requires exterior pedestrian access doors or gates to be self-closing and self-latching; other access doors or gates must be self-latching. If the release is less than fifty-four inches from the bottom, it must be on the pool side at least three inches below the top, with no openings greater than one-half inch within eighteen inches of the release. The section states an exception for gates equipped with a locking device. Confirm the applicable approved gate arrangement with Engineering and Construction Services; that exception is not a blanket waiver of pool security or the City’s separate closing-and-latching rules. The state’s nonmandatory Appendix BQ is not automatically an additional mandatory pool code.
• Oklahoma rural lawful fences: For the Title 4 lawful-fence framework, section 154 recognizes three substantial rails, or three boards at least six inches wide and three-quarters inch thick, fixed to substantial posts no more than ten feet apart for rails or eight feet for boards, in good repair; fence viewers may recognize an equivalent fence. The ordinary stated height is fifty-four inches, with the bottom rail, wire or board sixteen to twenty inches above ground. The barbed-wire alternative is three barbed wires or four wires of which two are barbed, posts no more than two rods apart with two stays, or one rod apart without stays, a top wire fifty-four to fifty-eight inches high and a bottom wire sixteen to twenty inches above ground. These rural standards do not override Midwest City’s animal-enclosure, dangerous-wire, zoning or placement rules.
• Partition-fence maintenance and tighter construction: Title 4 section 142 requires partition fences kept in good repair throughout the year unless both owners agree otherwise in writing. Section 154 permits a party wanting a tighter partition fence to add material at that party’s expense and later remove the added material. If both adjoining owners or occupants use the fence to restrain swine, goats or sheep, each must keep that party’s share sufficiently tight to restrain them.
• Equal boundary and division-fence maintenance: Under 60 O.S. section 70, coterminous owners are mutually and equally bound to maintain their boundaries and monuments and the fences between them. Its exception permits one owner to leave the land open as a public common; if that owner later encloses it, the owner must refund a just proportion of the division fence’s value at that time. Title 4 section 143 separately protects an owner who neither wants enclosure nor uses the land other than as commons from compelled contribution, but requires contribution under that article when the land is enclosed or used otherwise. These conditions do not automatically make a suburban neighbor liable for half the cost of every newly chosen privacy fence.
• Partition-fence disputes and fence viewers: Under Title 4 sections 139–141, either party to a dispute over erection or maintenance may apply to three disinterested freeholder fence viewers. Each party selects one and those two select the third. If a party fails or refuses to appoint a viewer within three days after the other party’s request, the county sheriff must appoint that party’s viewer on application by the party that requested the fence viewers. Each viewer is allowed one dollar per day, paid by the interested parties. After due notice, the viewers may assign each owner’s share and the time to build or repair it. If the required work is not done, the complainant may do it; the viewers must judge it sufficient and certify its value and their fees. After a demand remains unpaid for one month, the complainant may recover the certified amount by civil action with one percent monthly interest. This is a conditioned statutory procedure, not permission to bill a neighbor without the required allocation, work, certification and demand.
• Land previously enclosed in common: Under sections 144–145, where separately owned lands were enclosed together without a partition fence and one owner wants separate occupation, fence viewers may divide and assign the line if the other will not cooperate or build a sufficient share. They may assign in writing a reasonable construction period within six months, considering the season. After making that owner’s own share, the cooperating party may make the defaulting party’s share and use the statutory recovery route. In that common-enclosure situation, an owner proposing to open a strip at least sixteen feet wide for use as a public common must first give the other party six months’ notice.
• Joining an existing partition fence after enclosing land: Under section 146, an owner enclosing previously unenclosed land must, before joining an existing partition fence, pay half its value as determined by fence viewers or elect to rebuild and make half the fence. Failure to pay for thirty days after notice and demand permits the statutory recovery; failure to rebuild for two months after electing that option produces the stated liability. This prior-unenclosed-land joinder rule is different from automatic half-payment for every replacement fence.
• Recorded divisions and nonresident owners: Under section 147, a division between owners of improved lands made by fence viewers or written agreement and recorded with the county clerk binds owners, heirs and assigns to support their assigned portions. Section 148 includes the occupant or tenant as “owner” where the actual owner does not reside in the county, but the proceedings do not bind that owner unless notified. Section 151 also allows fence viewers to determine other questions within the article concerning fence rights and building, maintenance or removal duties. Apply this rural and partition-fence framework with the actual property facts, agreements and other legal proceedings; it does not override local zoning or decide a disputed title.
PRIVATE RESTRICTIONS
Recorded covenants, homeowners’ association architectural standards, deed restrictions, private easements and boundary, maintenance or cost agreements may apply independently of public approval. Check the actual parcel’s documents before changing height, materials, placement or gate access. Recorded patio-home maintenance access and approved subdivision screening obligations should not be overlooked when replacing an existing fence.
A permit, inspection or utility locate does not establish title, determine fence ownership or allocate neighbor costs. A written and recorded partition-fence division between owners of improved lands under 4 O.S. section 147 can bind owners and successors. Public statutory duties and removal protections are discussed above separately from private agreements; private approval does not excuse public noncompliance.
REVIEW AND ENFORCEMENT CONTEXT
Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:
• Public approval review: Residential fence permits, material and dimension submissions, Board-approved frontage exceptions, retaining walls, subdivision-wall grading and access conditions, and applicable approved subdivision conditions.
• Placement and maintenance complaints: Right-of-way or sight-triangle encroachments, blocked drainage, unsafe or deteriorated fences, coatings and prohibited materials.
• Conditional site review: Animal-enclosure separations and acreage, private-pool barriers and covers, patio-home and retaining-wall access easements, floodplain development permits and hydraulic limits, and floodplain-adjacent lot screening.
• Private review and disputes: Association architectural decisions and boundary, ownership or shared-cost disputes follow the relevant private documents and legal processes, separately from City permitting and code enforcement.
USING THIS INFORMATION
This page provides general orientation on how residential fence rules are structured and applied within the City of Midwest City, Oklahoma. Updated November 2026.
In addition to local fence rules, certain Oklahoma laws apply statewide. See Statewide Fence Laws in Oklahoma.
It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with municipal or unincorporated location, the authority responsible for each issue, current code requirements and amendments, zoning and site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural or livestock conditions, fence ownership and shared-fence duties, excavation requirements, and private restrictions subject to Oklahoma law. Before purchasing materials or beginning construction, confirm current requirements and site-specific limitations with Midwest City Engineering and Construction Services and Community Development and the responsible office for each applicable issue, and review applicable private agreements. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern. For legal advice or legal interpretation, consult a licensed attorney.