FENCE RULES – SEAGOVILLE (CITY), TEXAS

OVERVIEW

This guide covers residential fences within the corporate limits of the City of Seagoville, Texas, in Dallas and Kaufman counties.

Seagoville requires permits for new fences and larger repairs or changes. Interior side and rear fences generally may reach eight feet, while fences in front of the residence building line and on residential corner lots must meet decorative-design rules. Wood and vinyl are listed materials; new chain-link fencing is identified as black vinyl-coated, with a separate replacement allowance for existing residential chain-link. Steel posts, fire-access openings and clear sight areas are important construction requirements. Drainage easements prohibit fences, and utility easements require utility approvals. Agricultural properties, required subdivision screens and pool enclosures have additional conditions. Updated November 2026.

Quick question	Seagoville answer
Permit or approval	Permit required for new fencing and changes exceeding five panels; six-or-more-panel repairs or replacements require a permit. Submit a site plan.
Typical fence height	Interior side and rear: eight feet. Ordinary residential decorative fencing: 48 inches and at least 50% open, or the specified 42-inch solid masonry alternative. One-acre lots and agricultural fencing have separate conditions.
Placement & property lines	Front building lines, corners, visibility and recorded easements control placement. No general fence setback from every property line is stated; no part may encroach over another owner’s or public property.
Common fence materials	Wood: listed, with steel-post and construction rules. Vinyl/PVC: vinyl is listed; approval applies to the actual product. Chain-link: black vinyl-coated is listed for new fences; existing residential chain-link may be replaced with the same material.
Important local conditions	Fence rules may be further affected by corner lots, one-acre decorative designs, agricultural use and exemptions, pools, drainage or utility easements, required subdivision screens, floodplain conditions and approved development plans.
Official local resource	Seagoville Building Permits and Inspections

The table above is for quick reference; the corresponding sections below explain the additional conditions. Before purchasing materials or starting construction, read the sections that apply to your property, review the linked official sources and confirm site-specific questions with the Building Official or the responsible office identified below.

GOVERNANCE

Seagoville is a home-rule city with a council-manager government. The City Council adopts the municipal fence, zoning, subdivision and construction-code requirements. Article 21.08 of the Seagoville fence ordinance addresses fence permits, location, materials, repair and inspections; zoning and subdivision provisions add visibility, easement and required-screen conditions. The article defines a fence as a wall or structure more than 24 inches high intended to enclose, screen, restrict access to or decorate a lot, building or structure.

The Building Official approves fence materials and plans; the Building Inspection Department handles inspections, and the Permitting Department handles permit applications. Code Enforcement addresses fence maintenance and violations. The Board of Adjustment hears the fence appeals described below. The City Manager or designee administers floodplain requirements; the City Engineer handles the identified drainage, retaining-wall and subdivision matters. Public Works administers regulated stormwater submissions. Each utility, including city utilities, has a separate role when a utility easement is involved.

Seagoville adopts the 2024 International Residential Code and 2024 International Swimming Pool and Spa Code, with local amendments. The fence article contains its own permit requirements. Approved planned-development zoning and site plans may change screening or landscaping conditions for an individual property.

• Agricultural property: The fence article exempts fences in an AG-zoned district only when the property also has an agricultural exemption and is used for agricultural purposes, except where a provision specifically applies to AG property. These are three combined conditions. Separate pipe-rail, barbed-wire, mesh and electric-fence provisions have their own conditions below. Detached one-family homes are permitted in the AG district. State agricultural-operation protections have separate statutory qualifications; AG zoning alone does not establish immunity.

• State limits on city agricultural regulation: Under Agriculture Code §§251.005(c) and 251.0055, a city requirement applies to an agricultural operation within its corporate limits only under the statutory conditions. Clear and convincing evidence must show that less restrictive means cannot address the requirement’s purpose and that it is necessary to protect residents in the immediate vicinity, or persons on public property in the immediate vicinity, from imminent danger of explosion; flooding; vermin or insect infestation; physical injury; spread of an identified contagious disease directly attributable to the operation; removal of lateral or subjacent support; an identified water-supply contamination source; radiation; improper toxic-material storage; crops or vegetation causing traffic hazards; or firearms/other weapons discharge subject to Local Government Code §229.002. The City Council must find by resolution that the requirement is necessary to protect public health, based on a previously obtained and reviewed city health officer/consultant report identifying the hazards, necessity and manner of regulation, effects on generally accepted agricultural practices and any required explanation for restricting a practice identified as posing no public-health threat. The requirement must also avoid the statute’s specific prohibitions.

• Specific agricultural exceptions: Section 251.0055 restricts city prohibitions on generally accepted agricultural practices except through that process; protects growing/harvesting vegetation for animal feed, livestock forage or wildlife-management forage subject to the vegetation-height exception; and protects necessary pesticide/other vermin or disease-bearing-insect control. A city may not require the operation to have the specified constitutional agricultural, farm, ranch, wildlife-management or timber-use designation, or require the owner/lessee to mow, bale, shred or hoe material on an adjacent public-road right-of-way. An agricultural vegetation-height maximum must allow at least 12 inches and apply only within ten feet of a boundary adjoining a public sidewalk/street/highway or another owner’s property containing an inhabited structure. A city dog-restraint requirement does not apply while a dog protects livestock on property controlled by the property owner. A city may require the specified written wildlife-management plan to establish that wildlife-management activities constitute an agricultural operation. These state conditions are distinct from the fence article’s local exemption.

• Agricultural improvements: Agriculture Code §251.006 includes qualifying pens, barns, fences and other improvements designed for sheltering, restricting or feeding animal/aquatic life, storing produce/feed, or storing/maintaining agricultural implements or equipment. Agricultural land includes land qualifying for agricultural-use appraisal and other land where agricultural operations exist or may occur. An owner, lessee or occupant of agricultural land is not liable to the state, a governmental unit, or the owner, lessee or occupant of other agricultural land for construction or maintenance of such an improvement when its construction was not expressly prohibited by statute or a governmental requirement adopted in accordance with §251.005 in effect when it was built. A qualifying improvement is not a nuisance and is not otherwise subject to suit or injunction. Enforcement of state or federal statutes remains reserved.

PERMIT AND APPROVAL REQUIREMENTS

• Fence permit: Obtain a permit before installing a fence or making alterations, additions or changes exceeding five panels. Six-or-more-panel repairs or replacements expressly require a permit. A fence permit is valid for no longer than 180 days. Repairs and maintenance must use similar materials. Pay the fee under the city’s current master fee schedule before issuance; starting covered construction, erection or relocation before obtaining the permit doubles the fee without excusing compliance.

• Application and plans: Provide a site plan showing lot size, all improvements and proposed fence location. Identify fence style, material, design and height; show utility, drainage and other easements with their width and length; and supply information required by the applicable fence provisions. Residential decorative fencing requires a site plan, and the Building Official may require a survey. Decorative fencing must use new material and receive approval.

• Contractor or homeowner work: A hired fence contractor must be registered with the city. An owner may personally build a fence at an owner-occupied residential homestead after obtaining and paying for the permit, using compliant materials and work and securing inspection approval. Anyone other than that owner working on the fence must hold city fence-contractor registration.

• Inspection: When a permitted fence is complete, notify the Building Inspection Department within ten days. The department accepts compliant work or issues a deficiency notice. Correct deficiencies within 30 days; an additional 30 days may be granted for good cause.

• Easement approvals: Fences are prohibited in drainage easements. In a utility easement, submit approval letters from every utility using or authorized to use it, including city utilities. Recorded plat restrictions and access rights also apply.

• Floodplain development: Manmade changes such as structures, fill, grading and excavation within the mapped special flood-hazard area require the applicable floodplain development permit. Discuss a fence project in that area with the Floodplain Administrator before work. Floodway conditions are described below.

• Other affected work: City permission and any other agency permission having jurisdiction are required before deepening, widening, filling, rerouting or otherwise changing a ditch, channel, stream or drainageway. A swale needed to convey the 100-year flow requires plan approval and necessary easement dedication. Retaining-wall design/construction requires City Engineer approval under the applicable subdivision provisions. Work in the public right-of-way has separate permit or registration requirements; this is distinct from a fence wholly on private property.

• Pool enclosures: Pool fences and enclosures must comply with applicable law and the city’s adopted, amended pool code. Required enclosures and safety devices must be maintained. The ordinary fence-permit requirements also apply to covered fence work. Confirm the applicable pool-barrier design, gate hardware, permitted alternatives and requirements for an existing or altered pool with the Building Official before construction. The townhouse-district rules below also apply where relevant.

• Stop-work orders: Work contrary to the fence article or performed dangerously must stop upon official notice. The written notice ordinarily states the conditions for resuming work; an emergency can justify stopping work before written notice.

• Appeals: A directly affected person may appeal an official fence decision or notice to the Board of Adjustment by written application within 20 days after service. The board meets within 20 days of filing or at the stated periodic meeting. An ordinary appeal stays enforcement; an imminent-danger notice is excluded.

FENCE PLACEMENT RULES

• Front and corner locations: In single-family, duplex, apartment, townhouse and mobile-home-subdivision zoning, a fence in front of the required residence building line must qualify as residential decorative fencing. Residential corner lots must meet the decorative-design requirement. A residential front-yard fence existing before July 2023 may be repaired or replaced after damage, with replacement within 90 days of the damage.

• Boundaries and public property: Keep the fence, guide wires, braces and every other part off and from protruding over another owner’s property or city/state property. Establish the legal boundary and actual right-of-way before setting posts; the curb, paving edge and existing fence may differ from those lines. No general property-line setback replaces the specific building-line, easement and visibility restrictions.

• Meters and cleanouts: Residential decorative fencing may not obstruct city access to a water meter or city cleanout. Keep at least a four-foot opening or gate providing emergency fire access to all side and rear yards.

• Recorded easements: Check the actual plat and easement instruments. City or utility easements can allow removal of interfering fences and access for system work. Recorded dedication conditions may prohibit fences across shown easements, even when the fence article separately offers a utility-letter process. Visibility, access and maintenance easements prohibit fences or vegetation that endanger sight lines; dedicated fire lanes must remain free of fences and other obstructions.

• Required subdivision screens: An existing required screening device that is damaged or destroyed must be repaired or replaced with the same materials and restored appearance. Do not put wood or other privacy fencing immediately behind or abutting approved alternative screening made of living landscaping, berms, retaining walls or open fence sections. Required screens can have a maintenance easement of at least five feet on the private-lot side dedicated to the homeowners/property owners association; check the actual recorded location. Required screening walls are maintained by the city-approved association. Required screening must attain at least six feet and 90% opacity within three years of initial installation or planting; preserve the approved living-screen and maintenance conditions.

• Retaining walls: The property owner maintains retaining walls. A retaining wall may not be built in any utility or drainage easement without City Engineer approval. This wall-specific approval provision does not remove the fence prohibition in drainage easements.

• Drainage and stormwater: Keep private drainage facilities free of flow obstructions. Land adjoining a natural channel or creek not maintained by the city must preserve free flow, including removal of debris, overgrowth, fallen limbs/trees and unapproved structures. Property-line swale maintenance is the owner’s responsibility. Respect recorded stormwater-facility maintenance/access easements, which bind later owners. Prevent concrete/mortar debris, obstructing materials and harmful construction sediment from reaching the storm-drain system under the city’s discharge rules.

• Floodways: Regulatory floodway encroachments generally require hydrologic/hydraulic evidence of no increase in base-flood levels. Obtain the applicable floodplain determination and development permit before placing an obstruction; ordinary fence permission does not clear a floodway encroachment.

• Joint or attached fences: Under Agriculture Code §§143.121–.123, do not remove a jointly owned dividing fence, or a fence attached to another person’s fence, without mutual consent or the applicable statutory process. A person owning an interest in an attached fence may withdraw it after six months’ written notice to the specified other owner or representative. An owner whose fence is wholly on that owner’s land may require disconnection of an attached fence after the corresponding six-month written notice. Ownership, attachment and proper notice recipients matter; ordinary fence removal has no universal six-month rule.

• Agricultural and owner-operated excavation exceptions: Utilities Code §251.156(a)(4) excepts activities on private property connected with agricultural operations, defined by the referenced Tax Code §23.51(2) activities, from §251.151 notice. Section 251.156(a)(6) separately excepts excavation by or for a person who owns, leases or holds a mineral leasehold interest in the property AND operates every underground facility at the excavation site. Owning the land alone does not meet that second exception. These excavator-notice exceptions differ from §251.003’s facility exemptions, including a line solely on its owner’s property serving only that owner or tenant. Private lines may therefore need separate locating; a notice exception does not establish that all utilities are marked or waive a separate pipeline duty.

• Construction affecting a pipeline: Health and Safety Code §§756.121–.123 separately addresses building, structures, driveways or other construction located on, across, over or under a pipeline easement/right-of-way, or physically impacting or creating risk to the pipeline. Before covered building, repair, replacement or maintenance, notify the operator and meet a statutory alternative: the operator determines no increased public or pipeline-damage risk; if it determines increased risk, pay before proceeding the reasonable, necessary and documented cost of protective fortifications, barriers, conduits or other necessary changes/improvements; proceed under an existing written agreement; or undertake prompt regulated-utility work required by a natural disaster. A contrary written agreement with the affected pipeline owner/operator can govern applicability. The subchapter excludes municipal construction on municipally owned property unless for private commercial use, and the specified navigation-district/port-authority property. These are separate conditions from an 811 request, not a universal pipeline setback.

• Before digging posts: Request a Texas811 utility locate, follow the ticket’s lawful start instructions, check both responses and markings, resolve missing or conflicting information through the ticket process, protect marks and dig carefully. Utilities Code Chapter 251 generally covers mechanized or explosive excavation reaching 16 inches or more, subject to its actual exclusions and notice exceptions above. Ordinary notice must be given within the statutory 14-day advance window and at least 48 hours before work, excluding weekends and legal holidays. Separate Railroad Commission pipeline rules also cover manual excavation beyond 16 inches; their ticket/refresh provisions generally use 14 working days unless the excavator and operator have a qualifying longer written agreement signed and dated, and records are kept four years. A locate does not grant property/easement permission or replace permits or separate pipeline construction requirements. Report facility damage immediately to the operator and use emergency services when danger warrants.

FENCE HEIGHT AND VISIBILITY RULES

• Measurement and ordinary side/rear height: Fence height is measured from ground level at the fence base to its uppermost part. Interior-lot side-yard fences may be up to eight feet; rear-yard fences may be up to eight feet, subject to the article’s applicability and the special conditions below.

• Residential decorative design: Ordinary residential decorative fencing may be wrought iron, vinyl or wood, or wrought iron combined with rock, brick or stone columns. Maximum height is 48 inches with at least 50% open area. The solid alternative is no more than 42 inches, using brick, stone or rock and same-material columns. The residential decorative definition requires at least a four-foot gate.

• Lots of one acre or more: The separate decorative definition permits a six-foot maximum with at least 50% open area, using its listed wrought iron, vinyl, wood, black vinyl-coated chain-link or wrought-iron/rock/stone-column design. Its solid masonry alternative remains 42 inches with same-material columns. Decorative gates may reach ten feet; an attached crossbar requires 14 feet of height clearance and 24 feet of width for fire access. Front-building-line and residential-corner clauses still specify residential decorative design, so obtain Building Official approval of the applicable design before using the one-acre dimensions in those locations.

• Sloping ground: Where significant slope toward adjacent grade prevents a constructed six-foot fence from providing an effective level six-foot enclosure, the Building Official may waive the height restriction to provide an effective six-foot fence consistent with surrounding conditions.

• Garage/carport access: The fence definition specifies a ten-foot visibility triangle measured from the property-line corner in both directions on both sides of a residential rear/side garage or carport access drive. It cross-refers to the zoning alley-intersection provision. The zoning driveway/public-street rule below separately uses 25 feet.

• Street, driveway and alley triangles: The zoning sight-distance requirements require unobstructed cross-visibility between 30 inches and eight feet above ground. At two alleys or an alley/public street, measure at least ten feet along each side from the intersection and join the endpoints. At two public streets, or a private driveway/public street, measure at least 25 feet along the rights-of-way or driveway curbline/street right-of-way and join the endpoints. Trees are allowed only with limbs and foliage outside the cross-visibility zone. Developed detached single-family/two-family lots remain subject to visibility and maintenance rules even when exempt from new-landscaping requirements.

• Pavement edge and corner visibility: Fences and walls must be at least three feet from the edge of street pavement under the landscaping/visibility provision, in addition to right-of-way restrictions. On corner lots with required front and side yards, no fence, wall, structure, sign, tree, shrub or hedge may endanger traffic by obstructing the view; a bank preventing clear view must be moved.

• Platted visibility easements: Subdivision visibility-easement clips use separate dimensions: arterial/arterial, 40 by 40 feet; collector or residential street onto arterial, 25 by 25 feet; collector/residential street intersections, ten by ten feet; alley/street, ten by ten feet; alley/alley, 20 by 20 feet. The 25-foot branch also covers private multifamily/nonresidential driveways onto streets. Fixed items, fences and walls within these easements are limited to 30 inches, maintaining cross-visibility from 30 inches to eight feet. Apply the recorded easement as well as the separate zoning triangles.

• Existing required subdivision screens: The special required-screen range is six to eight feet. Decorative columns or similar features may add up to two feet, totaling ten feet, when those elements occupy no more than 10% of the wall length in elevation. Greater height requires commission approval on the applicable screening plans. Preserve approved screen conditions when repairing or replacing one.

• AG front/side livestock fencing: The AG-specific front/side barbed or metal/wire livestock fence may not exceed six feet above adjacent grade. This is separate from ordinary residential decorative fencing.

MATERIAL AND CONSTRUCTION LIMITS

• Listed materials: The fence article lists wood privacy, wood split rail, vinyl, black vinyl-coated chain-link, brick/masonry, rock/stone, decorative fencing, cementitious panels, wrought iron, wrought iron combined with rock/stone/brick, and visual screening. All fencing materials require Building Official approval. Existing residential chain-link may be replaced with the same materials. Decorative designs have the more specific material, openness and new-material conditions above.

• Prohibited substitutes: Products made for other uses may not be used as fencing. Named examples include plywood, pallets, R-panels, corrugated steel and fiberglass panels.

• Posts and wood panels: Wood posts are prohibited under the fence article. Wood privacy panels require at least three cross runners. New installation in an existing neighborhood/residential district and repair or replacement of six or more panels requires Schedule 40 steel pipe posts buried two feet in concrete. Replace damaged posts. Apply the article’s actual agricultural exemption and AG-specific rules where relevant.

• Agricultural pipe, barbed wire and mesh: Pipe rail is allowed on lots of at least one acre that are AG-zoned or have the specified agricultural exemption from the Dallas or Kaufman appraisal district. Barbed wire is limited to AG-zoned or qualifying appraisal-exempt property. Mesh is allowed only with pipe rail or barbed wire on those qualifying properties. The separate AG front/side livestock-fence provision permits heavy-duty steel T-posts or steel pipe, with no wood posts.

• Electric agricultural fences: Electric fencing is limited to AG-zoned property of at least one acre. Use properly stretched copper or aluminum wire at least 16 gauge on uniform straight posts no more than ten feet apart, with glass, plastic or porcelain insulators; glass bottles are prohibited. Only one electric wire is allowed, inside the fence and 18–36 inches above ground. Use a factory charger bearing a UL-approved seal, secured at least 24 inches above ground, with copper ground wire to an approved ground rod. DC or AC power may be used. AC supply requires an electrical permit, underground ENT conduit to an approved weather-type box/GFCI plug and no extension cord; the provision specifies 115-volt AC supply, output no greater than 24 volts DC and overload fuse. Warning signs every 100 feet must be in English and Spanish, with one-inch white letters on red, on a 12-by-six-inch sign.

• Pool barriers: Maintain a compliant pool enclosure and safety devices under the city’s adopted pool code. For a pool in the TH townhouse district, a permanent four-foot fence or wall must surround the pool, with a gate locked when unused; City Plan Commission approval also applies; the commission may set pool/equipment distances from property lines to protect neighboring peace and comfort. Pool lighting must eliminate direct rays on adjoining premises, and equipment must be located and screened against interference with adjoining occupants. Confirm the applicable barrier height, openings, gate/latch hardware, dwelling-door protections and allowed alternatives with the Building Official. Multiunit or association pools have a separate Health and Safety Code Chapter 757 branch; new pools in that branch must also meet the locally adopted pool code.

• Animal enclosures at homes: A dog kept on the owner’s premises must be contained by a substantial fence of sufficient strength and height to prevent escape, kept inside the house, or secured under the animal ordinance’s restraint alternative, subject to other applicable animal law. A dangerous dog must be restrained by an immediately controlled leash or a secure enclosure: locked, excluding the public including children, preventing escape/release, clearly marked and conforming to Animal Control requirements. Each enclosure entrance requires a sign stating “beware of dangerous dog.”

• Livestock and poultry at rural residences: The animal ordinance requires at least one fenced acre of accessible roaming space for livestock, including cows, horses, mules, jacks, jennies, goats and sheep. It permits one mother-and-offspring-under-six-months unit per acre and requires livestock further than 100 feet from the nearest private residence or public building. Six or fewer hens may be kept on less than one fenced acre, with their structure/enclosure at least 25 feet from those buildings. The rooster rule combines greater-than-one-acre wording with an at-least-one-fenced-acre branch; confirm an exactly-one-acre proposal with Animal Control. It requires at least six hens, allows at most one rooster per six hens and 20 chickens total per acre, and requires more than 100 feet from those buildings. A required FFA/4-H student project may receive a written, inspection-based City Manager/designee exception for up to 90 days per calendar year, withdrawable for nuisance; sanitation and other retained animal provisions still apply. Keep animal pens/enclosures sanitary and free of offensive or fly-breeding conditions.

• Special home equipment or storage: Where an approved wind-energy system uses fencing to secure equipment/access doors, it must prevent unauthorized entry; locked access is an alternative where appropriate. Collector antique/special-interest vehicle exceptions require ordinary-public-view screening, using a fence, rapidly growing trees, shrubs or other appropriate means, together with the applicable orderly/non-health-hazard conditions. The abandoned/junked trailer, boat, RV, camper or farm-equipment branch also has an enclosed-building or public-view-screening exception; screening does not authorize every otherwise prohibited use.

• Upkeep: Keep fences vertical and in good condition. Repair or replace damaged, removed, rotted, leaning or missing portions with comparable material within 30 days of the event. Keep vegetation from growing into the fence, remove graffiti and replace damaged posts. A separate violation letter allows 15 days from the letter to correct the stated violation. Structurally unsound fences and hazardous fence/debris conditions can also fall under nuisance and dangerous/substandard-building procedures.

PRIVATE RESTRICTIONS

Recorded covenants, association architectural requirements, private easements and boundary, maintenance or cost-sharing agreements can independently affect the design and placement of a fence. Obtain required association approval as well as city permits. Seagoville states that it does not enforce protective covenants or deed restrictions. Public plat/common-element maintenance provisions remain separate. A city permit does not decide fence ownership, boundary disputes or who pays.

Texas Property Code §§202.022–202.023 limits certain association restrictions. Section 202.022 protects a qualifying nonclimbable enclosure for a pool, spa or other water feature: transparent mesh or clear panels in a metal frame, no more than six feet high and compliant with applicable safety law. Associations may regulate appearance and colors within the statute but may not prohibit its protected black transparent-mesh/black-frame form. The six-foot definition is not a city pool-barrier minimum.

Subject to its retained controls, §202.023 prohibits an association from adopting or enforcing a restrictive covenant that prevents an owner from building or installing security measures, including security cameras, motion detectors or perimeter fencing. The retained controls include fence type; obstructions of licensed areas, sidewalks and drainage; driveway-gate setbacks of at least ten feet from the right-of-way when the driveway intersects a laned roadway; and a front-building-line prohibition when the governing covenant provides it. It excludes condominiums under Chapters 81/82 and Chapter 215 master mixed-use associations. Owners may maintain qualifying perimeter or front-building-line fences installed before September 1, 2025, notwithstanding subsection (c); that maintenance protection does not automatically cover expansion or replacement. The front-building-line prohibition has exceptions for a protected address or a law-enforcement-documented enhanced security need; those exceptions do not erase every other retained control.

REVIEW AND ENFORCEMENT CONTEXT

Fence issues are typically reviewed during permit or approval review when required, and through complaint-based code enforcement. Examples include:

• Permits and inspections: New fences, larger panel repairs, contractor registration, site plans, approved materials and completion inspections.

• Location and design: Front/corner decorative fencing, height, steel posts, fire access, visibility triangles and encroachment.

• Site and safety conditions: Drainage/utility easements, recorded screens, retaining walls, floodplain or drainage changes, pool enclosures, animal containment and unsafe or deteriorated fences.

Stop-work orders and fence appeals follow the procedures in Permit and Approval Requirements above. Private association enforcement, ownership disputes and private maintenance agreements remain separate.

USING THIS INFORMATION

This page provides general orientation on how residential fence rules are structured and applied within the City of Seagoville, Texas. Updated November 2026.

In addition to local fence rules, certain Texas laws apply statewide. See Statewide Fence Laws in Texas.

It is not legal advice and does not replace official statutes, ordinances, orders, permits, certificates, development approvals, applicable building-code requirements, surveys, recorded documents or professional guidance. Rules and interpretations may change, and application may vary with municipal or unincorporated location, applicable extraterritorial authority, zoning or special-area status, code adoption and amendments, site conditions, subdivision or plat conditions, easements, rights-of-way, drainage and floodplain requirements, historic or design districts, pool use, agricultural operations and stock laws, fence ownership or attachment, coastal or public-access conditions, utility and pipeline excavation requirements, and private restrictions subject to Texas law. Before purchasing materials or beginning construction, confirm current requirements and site-specific limitations with the Building Official and the responsible office for each applicable issue, and review applicable private agreements. If this page conflicts with controlling law, adopted regulations or official requirements, the controlling authorities govern. For legal advice or legal interpretation, consult a licensed attorney.